Endress+Hauser Levelflex FMP53 FOUNDATION Fieldbus User manual

Products Solutions Services
Operating Instructions
Levelflex FMP53
FOUNDATION Fieldbus
Guided wave radar
BA01053F/00/EN/03.15
71293317
01.01.zz (Device software)

Levelflex FMP53 FOUNDATION Fieldbus
2 Endress+Hauser
TAG No.: XXX000
Ser. No.: X000X000000
Order code 00X00-XXXX0XX0XXX
www.endress.com/deviceviewer Endress+Hauser Operations App
Serial number
A0023555

Levelflex FMP53 FOUNDATION Fieldbus Table of contents
Endress+Hauser 3
Table of contents
1 Important document information .... 6
1.1 Document function ..................... 6
1.2 Symbols .............................. 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Tool symbols .................... 6
1.2.4 Symbols for certain types of
information .................... 7
1.2.5 Symbols in graphics ............... 7
1.2.6 Symbols at the device ............. 8
1.3 Supplementary documentation ............. 9
1.3.1 Safety Instructions (XA) ........... 10
2 Basic safety instructions ........... 13
2.1 Requirements for the personnel ........... 13
2.2 Designated use ....................... 13
2.3 Workplace safety ...................... 14
2.4 Operational safety ..................... 14
2.5 Product safety ........................ 14
3 Product description ................ 15
3.1 Product design ........................ 15
3.1.1 Levelflex FMP53 ................ 15
3.1.2 Electronics housing .............. 16
3.2 Registered trademarks .................. 17
4 Incoming acceptance and product
identification ..................... 18
4.1 Incoming acceptance ................... 18
4.2 Product identification .................. 18
4.2.1 Nameplate .................... 19
5 Storage, Transport ................ 20
5.1 Storage conditions ..................... 20
5.2 Transport product to the measuring point .... 20
6 Mounting ......................... 21
6.1 Mounting requirements ................. 21
6.1.1 Suitable mounting position ........ 21
6.1.2 Applications with restricted
mounting space ................. 23
6.1.3 Notes on the mechanical load of the
probe ........................ 25
6.1.4 Special mounting conditions ....... 26
6.2 Mounting the device ................... 32
6.2.1 Required mounting tools .......... 32
6.2.2 Mounting the "Sensor remote"
version ....................... 32
6.2.3 Turning the transmitter housing .... 33
6.2.4 Turning the display module ........ 34
6.3 Post-installation check .................. 35
7 Electrical connection .............. 36
7.1 Connection conditions .................. 36
7.1.1 Terminal assignment ............. 36
7.1.2 Cable specification ............... 37
7.1.3 Device plug connectors ........... 38
7.1.4 Power supply .................. 39
7.1.5 Overvoltage protection ........... 39
7.2 Connecting the device .................. 40
7.2.1 Pluggable spring-force terminals .... 41
7.3 Post-connection check .................. 41
8 Operation options ................. 43
8.1 Overview ............................ 43
8.1.1 Local operation ................. 43
8.1.2 Operation with remote display and
operating module FHX50 .......... 43
8.1.3 Remote operation ............... 44
8.2 Structure and function of the operating
menu .............................. 46
8.2.1 Structure of the operating menu .... 46
8.2.2 User roles and related access
authorization .................. 47
8.2.3 Write protection via access code ..... 48
8.2.4 Disabling write protection via access
code ......................... 49
8.2.5 Deactivation of the write protection
via access code ................. 49
8.2.6 Write protection via write protection
switch ........................ 50
8.2.7 Enabling and disabling the keypad
lock ......................... 52
8.3 Display and operating module ............ 53
8.3.1 Display appearance .............. 53
8.3.2 Operating elements .............. 56
8.3.3 Entering numbers and text ........ 57
8.3.4 Opening the context menu ......... 59
8.3.5 Envelope curve on the display and
operating module ............... 60
9 Integration into a FOUNDATION
Fieldbus network .................. 61
9.1 Device Description (DD) ................. 61
9.2 Integration into the FOUNDATION Fieldbus
network ............................ 61
9.3 Device identification and addressing ........ 61
9.4 Block model .......................... 62
9.4.1 Blocks of the device software ....... 62
9.4.2 Block configuration when device is
delivered ...................... 63
9.5 Assignment of the measured values
(CHANNEL) in an AI Block ............... 63
9.6 Index tables of Endress+Hauser parameters .. 64
9.6.1 Setup Transducer Block ........... 64

Table of contents Levelflex FMP53 FOUNDATION Fieldbus
4 Endress+Hauser
9.6.2 Advanced Setup Transducer Block ... 65
9.6.3 Display Transducer Block .......... 66
9.6.4 Diagnostic Transducer Block ....... 67
9.6.5 Expert Configuration Transducer
Block ........................ 68
9.6.6 Expert Information Transducer
Block ........................ 70
9.6.7 Service Sensor Transducer Block .... 71
9.6.8 Service Information Transducer
Block ........................ 71
9.6.9 Data Transfer Transducer Block ..... 71
9.7 Methods ............................ 73
10 Commissioning via wizard ......... 74
11 Commissioning via operating
menu ............................. 75
11.1 Installation and function check ............ 75
11.2 Setting the operating language ............ 75
11.3 Configuration of a level measurement ...... 76
11.4 Recording the reference curve ............ 78
11.5 Configuration of the on-site display ........ 79
11.5.1 Factory settings of the on-site
display for level measurements ..... 79
11.5.2 Adjustment of the on-site display ... 79
11.6 Configuration management .............. 80
11.7 Protection of the settings against
unauthorized changes .................. 81
12 Commissioning (block-based
operation) ........................ 82
12.1 Function check ....................... 82
12.2 Block configuration .................... 82
12.2.1 Preparatory steps ............... 82
12.2.2 Configuring the Resource Block ..... 82
12.2.3 Configuring the Transducer Blocks ... 82
12.2.4 Configuring the Analog Input
Blocks ........................ 83
12.2.5 Additional configuration .......... 83
12.3 Scaling of the measured value in an AI Block .. 83
12.4 Language selection .................... 84
12.5 Configuration of a level measurement ...... 85
12.6 Configuration of the on-site display ........ 86
12.6.1 Factory settings of the on-site
display for level measurements ..... 86
12.7 Configuration management .............. 86
12.8 Configuration of the event behavior
according to the FOUNDATION Fieldbus
specification FF912 .................... 88
12.8.1 Groups of events ................ 89
12.8.2 Allocation parameters ............ 91
12.8.3 Configurable area ............... 94
12.8.4 Transmission of the event meassages
to the bus ..................... 95
12.9 Protection of the settings against
unauthorized changes .................. 95
13 Diagnostics and troubleshooting ... 96
13.1 General trouble shooting ................ 96
13.1.1 General errors .................. 96
13.1.2 Parametrization errors ........... 97
13.2 Diagnostic information on local display ...... 98
13.2.1 Diagnostic message .............. 98
13.2.2 Calling up remedial measures ..... 100
13.3 Diagnostic event in the operating tool ...... 101
13.4 Diagnostic messages in the DIAGNOSTIC
Transducer Block (TRDDIAG) ............ 101
13.5 Diagnostic list ....................... 101
13.6 Event logbook ....................... 102
13.6.1 Event history .................. 102
13.6.2 Filtering the event logbook ....... 102
13.6.3 Overview of information events .... 102
13.7 Firmware history ..................... 104
14 Maintenance .................... 105
14.1 Exterior cleaning ..................... 105
14.2 Cleaning the probe .................... 105
14.2.1 Cleaning the probe in the tank ..... 105
14.2.2 Cleaning the probe outside the
tank ........................ 106
15 Repairs .......................... 107
15.1 General information on repairs ........... 107
15.1.1 Repair concept ................ 107
15.1.2 Repairs to Ex-approved devices .... 107
15.1.3 Replacement of an electronics
module ...................... 107
15.1.4 Replacement of a device ......... 107
15.2 Spare parts ......................... 108
15.3 Return ............................. 108
15.4 Disposal ........................... 108
16 Accessories ...................... 109
16.1 Device-specific accessories .............. 109
16.1.1 Weather protection cover ........ 109
16.1.2 Mounting bracket for the electronics
housing ..................... 110
16.1.3 Weld-in adpater ............... 110
16.1.4 Protective cover ................ 111
16.1.5 Calibration kit ................. 111
16.1.6 Remote display FHX50 .......... 112
16.1.7 Overvoltage protection .......... 113
16.2 Communication-specific accessories ....... 114
16.3 Service-specific accessories .............. 114
16.4 System components ................... 114
17 Operating menu .................. 115
17.1 Overview of the operating menu (display
module) ........................... 115
17.2 Overview of the operating menu (operating
tool) .............................. 122
17.3 "Setup" menu ........................ 128
17.3.1 "Mapping" wizard ............... 135

Levelflex FMP53 FOUNDATION Fieldbus Table of contents
Endress+Hauser 5
17.3.2 "Analog input 1 to 5" submenu ..... 136
17.3.3 "Advanced setup" submenu ........ 138
17.4 "Diagnostics" menu .................... 180
17.4.1 "Diagnostic list" submenu ......... 182
17.4.2 "Event logbook" submenu ......... 183
17.4.3 "Device information" submenu ..... 184
17.4.4 "Measured values" submenu ....... 186
17.4.5 "Analog input 1 to 5" submenu ..... 187
17.4.6 "Data logging" submenu .......... 189
17.4.7 "Simulation" submenu ........... 192
17.4.8 "Device check" submenu .......... 197
Index ................................. 199

Important document information Levelflex FMP53 FOUNDATION Fieldbus
6 Endress+Hauser
1 Important document information
1.1 Document function
These Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and
storage, to mounting, connection, operation and commissioning through to
troubleshooting, maintenance and disposal.
1.2 Symbols
1.2.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
NOTE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is
grounded via a grounding system.
Protective ground connection
A terminal which must be connected
to ground prior to establishing any
other connections.
Equipotential connection
A connection that has to be connected
to the plant grounding system: This
may be a potential equalization line
or a star grounding system depending
on national or company codes of
practice.
1.2.3 Tool symbols
Symbol Meaning
A0013442
Torx screwdriver
A0011220
Flat blade screwdriver

Levelflex FMP53 FOUNDATION Fieldbus Important document information
Endress+Hauser 7
Symbol Meaning
A0011219
Cross-head screwdriver
A0011221
Allen key
A0011222
Hexagon wrench
1.2.4 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation
Reference to page
Reference to graphic
,… ,
Series of steps
Result of a sequence of actions
Help in the event of a problem
Visual inspection
1.2.5 Symbols in graphics
Symbol Meaning
1, 2, 3 ... Item numbers
,… ,
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
-
Hazardous area
Indicates a hazardous area.
.
Safe area (non-hazardous area)
Indicates the non-hazardous area.

Important document information Levelflex FMP53 FOUNDATION Fieldbus
8 Endress+Hauser
1.2.6 Symbols at the device
Symbol Meaning
Safety instructions
Observe the safety instructions contained in the associated Operating Instructions.
Temperature resistance of the connection cables
Specifies the minimum value of the temperature resistance of the connection cables.

Levelflex FMP53 FOUNDATION Fieldbus Important document information
Endress+Hauser 9
1.3 Supplementary documentation
Document Purpose and content of the document
Technical Information
TI01002F (FMP53)
Planning aid for your device
The document contains all the technical data on the device and provides
an overview of the accessories and other products that can be ordered for
the device.
Brief Operating Instructions
KA01108F (FMP53, FOUNDATION
Fieldbus)
Guide that takes you quickly to the 1st measured value
The Brief Operating Instructions contain all the essential information
from incoming acceptance to initial commissioning.
Description of Device Parameters
GP01015F (FMP5x, FOUNDATION
Fieldbus)
Reference for your parameters
The document provides a detailed explanation of each individual
parameter in the operating menu. The description is aimed at those who
work with the device over the entire life cycle and perform specific
configurations.
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate
or scan the 2-D matrix code (QR code) on the nameplate.

Important document information Levelflex FMP53 FOUNDATION Fieldbus
10 Endress+Hauser
1.3.1 Safety Instructions (XA)
Depending on the approval, the following Safety Instructions (XA) are supplied with the
device. They are an integral part of the Operating Instructions.
Feature 010 Approval Available for Feature 020: "Power Supply; Output"
A 1) B 2) C 3) E 4)/G 5) K 6)/L 7)
BA ATEX II 1G Ex ia IIC T6 Ga FMP53 XA00496F XA01125F XA01126F XA00516F -
BB ATEX II 1/2G Ex ia IIC T6 Ga/Gb FMP53 XA00496F XA01125F XA01126F XA00516F -
BC ATEX II 1/2G Ex d[ia] IIC T6 Ga/Gb FMP53 XA00499F XA00499F XA00499F XA00519F XA01133F
BD ATEX II 1/3G Ex ic[ia] IIC T6 Ga/Gc FMP53 XA00497F XA01127F XA01128F XA00517F -
BG ATEX II 3G Ex nA IIC T6 Gc FMP53 XA00498F XA01130F XA01131F XA00518F XA01132F
BH ATEX II 3G Ex ic IIC T6 Gc FMP53 XA00498F XA01130F XA01131F XA00518F -
BL ATEX II 1/3G Ex nA[ia] IIC T6 Ga/Gc FMP53 XA00497F XA01127F XA01128F XA00517F XA01129F
B2 ATEX II 1/2G Ex ia IIC T6 Ga/Gb, 1/2D Ex ia IIIC Da/Db FMP53 XA00502F XA00502F XA00502F XA00522F -
B3 ATEX II 1/2G Ex d[ia] IIC T6 Ga/Gb, 1/2 D Ex t IIIC
Da/Db
FMP53 XA00503F XA00503F XA00503F XA00523F XA01136F
B4 ATEX II 1/2G Ex ia IIC T6 Ga/Gb, Ex d[ia] IIC T6 Ga/Gb FMP53 XA00500F XA01134F XA01135F XA00520F -
C2 CSA C/US IS Cl.I,II,III Div.1 Gr.A-G, NI Cl.1 Div.2, Ex ia FMP53 XA00530F XA00530F XA00530F XA00571F XA00530F
C3 CSA C/US XP Cl.I,II,III Div.1 Gr.A-G, NI Cl.1 Div.2, Ex d FMP53 XA00529F XA00529F XA00529F XA00570F XA00529F
FB FM IS Cl.I,II,III Div.1 Gr.A-G, AEx ia, NI Cl.1 Div.2 FMP53 XA00531F XA00531F XA00531F XA00573F XA00531F
FD FM XP Cl.I,II,III Div.1 Gr.A-G, AEx d, NI Cl.1 Div.2 FMP53 XA00532F XA00532F XA00532F XA00572F XA00532F
IA IEC Ex ia IIC T6 Ga FMP53 XA00496F XA01125F XA01126F XA00516F -
IB IEC Ex ia IIC T6 Ga/Gb FMP53 XA00496F XA01125F XA01126F XA00516F -
IC IEC Ex d[ia] IIC T6 Ga/Gb FMP53 XA00499F XA00499F XA00499F XA00519F XA01133F
ID IEC Ex ic[ia] IIC T6 Ga/Gc FMP53 XA00497F XA01127F XA01128F XA00517F -
IG IEC Ex nA IIC T6 Gc FMP53 XA00498F XA01130F XA01131F XA00518F XA01132F
IH IEC Ex ic IIC T6 Gc FMP53 XA00498F XA01130F XA01131F XA00518F -
IL IEC Ex nA[ia] IIC T6 Ga/Gc FMP53 XA00497F XA01127F XA01128F XA00517F XA01129F
I2 IEC Ex ia IIC T6 Ga/Gb, Ex ia IIIC Da/Db FMP53 XA00502F XA00502F XA00502F XA00522F -
I3 IEC Ex d [ia] IIC T6 Ga/Gb, Ex t IIIC Da/Db FMP53 XA00503F XA00503F XA00503F XA00523F XA01136F
KA KC Ex ia IIC T6 Ga FMP53 XA01169F - XA01169F - -
KB KC Ex ia IIC T6 Ga/Gb FMP53 XA01169F - XA01169F - -
KC KC Ex d[ia] IIC T6 FMP53 - - XA01170F - -
MA INMETRO Ex ia IIC T6 Ga FMP53 XA01038F XA01038F XA01038F - XA01038F
MC INMETRO Ex d[ia] IIC T6 Ga/Gb FMP53 XA01041F XA01041F XA01041F - XA01041F
MH INMETRO Ex ic IIC T6 Gc FMP53 XA01040F XA01040F XA01040F - XA01040F
NA NEPSI Ex ia IIC T6 Ga FMP53 XA00634F XA00634F XA00634F XA00640F XA00634F
NB NEPSI Ex ia IIC T6 Ga/Gb FMP53 XA00634F XA00634F XA00634F XA00640F XA00634F
NC NEPSI Ex d[ia] IIC T6 Ga/Gb FMP53 XA00636F XA00636F XA00636F XA00642F XA00636F
NG NEPSI Ex nA II T6 Gc FMP53 XA00635F XA00635F XA00635F XA00641F XA00635F
NH NEPSI Ex ic IIC T6 Gc FMP53 XA00635F XA00635F XA00635F XA00641F XA00635F
N2 NEPSI Ex ia IIC T6 Ga/Gb, Ex iaD 20/21 T85…90°C FMP53 XA00638F XA00638F XA00638F XA00644F XA00638F

Levelflex FMP53 FOUNDATION Fieldbus Important document information
Endress+Hauser 11
Feature 010 Approval Available for Feature 020: "Power Supply; Output"
A 1) B 2) C 3) E 4)/G 5) K 6)/L 7)
N3 NEPSI Ex d[ia] IIC T6 Ga/Gb, DIP A20/21 T85…90°C
IP66
FMP53 XA00639F XA00639F XA00639F XA00645F XA00639F
8A FM/CSA IS+XP Cl.I,II,III Div.1 Gr.A-G FMP53 XA00531F
XA00532F
XA00531F
XA00532F
XA00531F
XA00532F
XA00572F
XA00573F
XA00531F
XA00532F
1) A: 2-wire; 4-20mA HART
2) B: 2-wire; 4-20mA HART, switch output
3) C: 2-wire; 4-20mA HART, 4-20mA
4) E: 2-wire; FOUNDATION Fieldbus, switch output
5) G: 2-wire; PROFIBUS PA, switch output
6) K: 4-wire 90-253VAC; 4-20mA HART
7) L: 4-wire 10,4-48VDC; 4-20mA HART
For certified devices the relevant Safety Instructions (XA) are indicated on the
nameplate.

Important document information Levelflex FMP53 FOUNDATION Fieldbus
12 Endress+Hauser
Ex-marking in case of connected FHX50 remote display
If the device is prepared for the remote display FHX50 (product structure: feature 030:
Display, Operation", option L or M), the Ex marking of some certificates changes according
to the following table 1):
Feature 010 ("Approval") Feature 030 ("Display, Operation") Ex-marking
BG L or M ATEX II 3G Ex nA [ia Ga] IIC T6 Gc
BH L or M ATEX II 3G Ex ic [ia Ga] IIC T6 Gc
B3 L or M ATEX II 1/2G Ex d [ia] IIC T6 Ga/Gb,
ATEX II 1/2D Ex ta [ia Db] IIIC Txx°C Da/Db
IG L or M IECEx Ex nA [ia Ga] IIC T6 Gc
IH L or M IECEx Ex ic [ia Ga] IIC T6 Gc
I3 L or M IECEx Ex d [ia] IIC T6 Ga/Gb,
IECEx Ex ta [ia Db] IIIC Txx°C Da/Db
1) The marking of certificates not mentioned in this table are not affected by the FHX50.

Levelflex FMP53 FOUNDATION Fieldbus Basic safety instructions
Endress+Hauser 13
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before beginning work, the specialist staff must have read and understood the
instructions in the Operating Instructions and supplementary documentation as well as
in the certificates (depending on the application)
‣Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
‣Being instructed and authorized according to the requirements of the task by the
facility's owner-operator
‣Following the instructions in these Operating Instructions
2.2 Designated use
Application and measured materials
The measuring device described in these Operating Instructions is intended only for level
measurement of liquids. Depending on the version ordered the device can also measure
potentially explosive, flammable, poisonous and oxidizing materials.
Observing the limit values specified in the "Technical data" and listed in the Operating
Instructions and supplementary documentation, the measuring device may be used for the
following measurements only:
‣Measured process variables: level
‣Calculated process variables: Volume or mass in arbitrarily shaped vessels (calculated
from the level by the linearization functionality)
To ensure that the measuring device remains in proper condition for the operation time:
‣Use the measuring device only for measured materials against which the process-
wetted materials are adequately resistant.
‣Observe the limit values in "Technical data".
Incorrect use
The manufacturer is not liable for damage caused by improper or non-designated use.
Verification for borderline cases:
‣For special measured materials and cleaning agents, Endress+Hauser is glad to provide
assistance in verifying the corrosion resistance of wetted materials, but does not accept
any warranty or liability.
Residual risk
The electronics housing and its built-in components such as display module, main
electronics module and I/O electronics module may heat to 80 °C (176 °F) during operation
through heat transfer from the process as well as power dissipation within the electronics.
During operation the sensor may assume a temperature near the temperature of the
measured material.
Danger of burns due to heated surfaces!
‣For high process temperatures: Install protection against contact in order to prevent
burns.

Basic safety instructions Levelflex FMP53 FOUNDATION Fieldbus
14 Endress+Hauser
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
With divisible probe rods, medium may penetrate into the joints between the indivual
parts of the rod. This medium may escape when loosening the joints. In the case of
dangerous (e.g. aggressive or toxic) media this may cause injuries.
‣When loosening the joints between the individual parts of the probe rod: Wear
appropriate protective equipment according to the medium.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with the manufacturer.
Repair
To ensure continued operational safety and reliability,
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.
‣Use original spare parts and accessories from the manufacturer only.
Hazardous area
To eliminate a danger for persons or for the facility when the device is used in the
hazardous area (e.g. explosion protection, pressure vessel safety):
‣Based on the nameplate, check whether the ordered device is permitted for the
intended use in the hazardous area.
‣Observe the specifications in the separate supplementary documentation that is an
integral part of these Instructions.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet
state-of-the-art safety requirements, has been tested, and left the factory in a condition in
which they are safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC
directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.

Levelflex FMP53 FOUNDATION Fieldbus Product description
Endress+Hauser 15
3 Product description
3.1 Product design
3.1.1 Levelflex FMP53
1
2
3
A0013421
 1 Design of the Levelflex
1 Electronics housing
2 Process connection
3 Rod probe

Product description Levelflex FMP53 FOUNDATION Fieldbus
16 Endress+Hauser
3.1.2 Electronics housing
Esc
–+E
123
4
5
6
9
7
8
A0012422
 2 Design of the electronics housing
1 Electronics compartment cover
2 Display module
3 Main electronics module
4 Cable glands (1 or 2, depending on instrument version)
5 Nameplate
6 I/O electronics module
7 Terminals (pluggable spring terminals)
8 Connection compartment cover
9 Grounding terminal

Levelflex FMP53 FOUNDATION Fieldbus Product description
Endress+Hauser 17
3.2 Registered trademarks
FOUNDATIONTM Fieldbus
Registered trademark of the Fieldbus Foundation, Austin, Texas, USA
KALREZ®, VITON®
Registered trademark of DuPont Performance Elastomers L.L.C., Wilmington, USA
TEFLON®
Registered trademark of E.I. DuPont de Nemours & Co., Wilmington, USA
TRI CLAMP®
Registered trademark of Alfa Laval Inc., Kenosha, USA

Incoming acceptance and product identification Levelflex FMP53 FOUNDATION Fieldbus
18 Endress+Hauser
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
A0015502
DELIVERY NOTE
1 = 2
A0022480
Is the order code on the delivery
note (1) identical to the order
code on the product sticker (2)?
A0022486
A0015502
A0022489
Are the goods undamaged?
A0015502
DELIVERY NOTE
Made in Germany, 79689 Maulburg
A0022491
Do the nameplate data match
the ordering information on the
delivery note?
A0015502
A0022494
Is the DVD (operating tool)
present?
If required (see nameplate): Are
the Safety Instructions (XA)
present?
If one of the conditions does not comply, contact your Endress+Hauser distributor.
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
• Enter serial numbers from nameplates in W@M Device Viewer
( www.endress.com/deviceviewer ): All information about the measuring device is
displayed.
• Enter the serial number from the nameplates into the Endress+Hauser Operations App
or scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser
Operations App: all the information for the measuring device is displayed.

Levelflex FMP53 FOUNDATION Fieldbus Incoming acceptance and product identification
Endress+Hauser 19
4.2.1 Nameplate
20
21
22
24
25
23
26
12
3
4
5
6
7
8
9
10
19
18
17
16
15
14
Ext. ord. cd.:
Order code:
Ser. no.:
LN =
Lref =
Mat.:
Date:
FW: Dev.Rev.:
DeviceID:
Ta:
if modification
see sep. label
X =
MWP:
12
11
47 (1.85)
92 (3.62)
mm (in)
13
A0010725
 3 Nameplate of the Levelflex
1 Device name
2 Address of manufacturer
3 Order code
4 Serial number (Ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Process pressure
7 Gas phase compensation: reference distance
8 Certificate symbol
9 Certificate and approval relevant data
10 Degree of protection: e.g. IP, NEMA
11 Document number of the Safety Instructions: e.g. XA, ZD, ZE
12 2-D matrix code (QR code)
13 Modification mark
14 Manufacturing date: year-month
15 Permitted temperature range for cable
16 Geräterevision (Dev.Rev.)
17 Additional information about the device version (certificates, approvals, communication): e.g. SIL, PROFIBUS
18 Firmware version (FW)
19 CE mark, C-Tick
20 DeviceID
21 Material in contact with process
22 Permitted ambient temperature (Ta)
23 Size of the thread of the cable glands
24 Length of probe
25 Signal outputs
26 Operating voltage
Only 33 digits of the extended order code can be indicated on the nameplate. If the
extended order code exceeds 33 digits, the rest will not be shown. However, the
complete extended order code can be viewed in the operating menu of the device in
the Extended order code 1 to 3 parameter.

Storage, Transport Levelflex FMP53 FOUNDATION Fieldbus
20 Endress+Hauser
5 Storage, Transport
5.1 Storage conditions
• Permitted storage temperature: –40 to +80 °C (–40 to +176 °F)
• Use the original packaging.
5.2 Transport product to the measuring point
LWARNING
Housing or probe may be damaged or break away.
Risk of injury!
‣Transport the measuring device to the measuring point in its original packaging or at
the process connection.
‣Do not fasten lifting devices (hoisting slings, lifting eyes etc.) at the housing or the
probe but at the process connection. Take into account the mass center of the device in
order to avoid unintended tilting.
‣Comply with the safety instructions, transport conditions for devices over 18kg
(39.6lbs) (IEC61010).
A0014267