Endress+Hauser Memocheck Sim CYP03D User manual

Products Solutions Services
BA00481C/07/EN/15.13
71233207
valid from:
Software version 1.00.03
Operating Instructions
Memocheck Sim CYP03D
Testing tool for analysis measuring points

Endress+Hauser
CYP03D
Table of contents
1 Document information . . . . . . . 4
1.1 Safety messages . . . . . . . . . . . . . . . . . . . . . 4
1.2 Symbols used . . . . . . . . . . . . . . . . . . . . . . . 4
2 Basic safety instructions . . . . . . 5
2.1 Requirements for the personnel . . . . . . . 5
2.2 Designated use . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Workplace safety . . . . . . . . . . . . . . . . . . . . 5
2.4 Operational safety . . . . . . . . . . . . . . . . . . . 5
2.5 Product safety . . . . . . . . . . . . . . . . . . . . . . 6
3 Device description . . . . . . . . . . . 7
3.1 Measuring system . . . . . . . . . . . . . . . . . . . 7
3.2 IECEx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 ATEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Quick wiring guide in Ex areas . . . . . . . . . 9
3.5 Temperature classes . . . . . . . . . . . . . . . . 10
4 Incoming acceptance and
product identification . . . . . . . 11
4.1 Incoming acceptance . . . . . . . . . . . . . . . . 11
4.2 Product identification . . . . . . . . . . . . . . . 11
4.3 Scope of delivery . . . . . . . . . . . . . . . . . . . 12
4.4 Certificates and approvals . . . . . . . . . . . 12
5 Operation options . . . . . . . . . . 13
5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 Structure and function of the operating
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Commissioning. . . . . . . . . . . . . 18
6.1 Switching on the measuring device . . . . 18
6.2 Configuring the operating language and
getting started . . . . . . . . . . . . . . . . . . . . . 18
6.3 Configuring the measuring device . . . . . 20
6.4 Advanced settings . . . . . . . . . . . . . . . . . . 24
7 Diagnostics . . . . . . . . . . . . . . . . 38
8 Maintenance. . . . . . . . . . . . . . . 39
8.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.2 Battery replacement . . . . . . . . . . . . . . . . 39
8.3 Calibration and qualification . . . . . . . . . . 39
9 Repair. . . . . . . . . . . . . . . . . . . . . 40
9.1 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.2 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.3 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10 Accessories . . . . . . . . . . . . . . . . 41
10.1 Memosens data cable . . . . . . . . . . . . . . . . 41
10.2 Storage case . . . . . . . . . . . . . . . . . . . . . . . . 41
11 Technical data. . . . . . . . . . . . . . 42
11.1 Environment . . . . . . . . . . . . . . . . . . . . . . . 42
11.2 Mechanical construction . . . . . . . . . . . . . 42
12 Appendix . . . . . . . . . . . . . . . . . . 43
Index. . . . . . . . . . . . . . . . . . . . . . 45

Document information CYP03D
4Endress+Hauser
1 Document information
1.1 Safety messages
The structure, signal words and safety colors of the signs comply with the specifications of ANSI
Z535.6 ("Product safety information in product manuals, instructions and other collateral
materials").
1.2 Symbols used
Safety message structure Meaning
DANGER
!
Causes (/consequences)
Consequences if safety
message is not heeded
Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the situation will result in a fatal or serious
injury.
WARNING
!
Causes (/consequences)
Consequences if safety
message is not heeded
Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the situation can result in a fatal or serious
injury.
CAUTION
!
Causes (/consequences)
Consequences if safety
message is not heeded
Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more
serious injuries.
NOTICE
Cause/situation
Consequences if safety
message is not heeded
Action/note
This symbol alerts you to situations that can result in damage
to property and equipment.
Additional information, tip
Permitted or recommended
Forbidden or not recommended

CYP03D Basic safety instructions
Endress+Hauser 5
2 Basic safety instructions
2.1 Requirements for the personnel
Installation, commissioning, operation and maintenance of the measuring system must only
be carried out by specially trained technical personnel.
The technical personnel must be authorized to perform the tasks by the owner-operator.
The electrical connection may only be established by an electrical technician.
The technical personnel must have read and understood these Operating Instructions and
must follow the instructions they contain.
Faults at the measuring point may only be rectified by authorized and properly trained
personnel.
Repairs not described in the Operating Instructions provided may only be carried out
directly at the manufacturer's or by the Service Organization.
2.2 Designated use
If the device is used for any purpose other than that described, this poses a threat to the safety
of people and the entire measuring system and is thus not permitted.
The manufacturer does not accept liability for damage caused by improper or non-designated
use.
2.3 Workplace safety
As the user, you are responsible for observing the following safety regulations:
• Installation guidelines
• Local standards and regulations
Electromagnetic compatibility
The product has been tested for electromagnetic compatibility in accordance with the applicable
European standards for industrial environments.
The electromagnetic compatibility indicated only applies to a product that has been connected
as described in these
Operating Instructions.
2.4 Operational safety
Prior to commissioning the entire measuring point, check that all connections are correct.
Make sure that electric cables and hose connections are not damaged.
Do not commission damaged products. Protect them against unintentional startup. Label
and identify the damaged product as defective.
If the faults cannot be eliminated, take the products out of service and protect them against
unintentional startup.

Basic safety instructions CYP03D
6Endress+Hauser
2.5 Product safety
2.5.1 State of the art
The product is designed to meet state-of-the-art safety requirements, has been tested and left
the factory in a condition in which it is safe to operate.
The applicable regulations and European standards have been taken into account.
2.5.2 Safety instructions for electrical equipment in hazardous areas
The Memosens inductive sensor cable connection system consists of:
• Memocheck Sim (Memosens technology) CYP03D and
• Measuring cable CYK10
This connection system is approved for measuring applications in explosive atmospheres in
accordance with:
a) IECEx design approval, IECEx BVS 12.0007
b) ATEX design approval BVS 12 ATEX E 121 008 with amendments.
The IECEx certificate to this effect and the EC certificate of conformity for ATEX are an integral
part of these Operating Instructions.
• Power is supplied to the Memocheck Sim CYP03D via three alkaline batteries with a total
nominal voltage of 4.5 V. Only the following types of battery may be used for this purpose:
• Memocheck Sim CYP03D may not be opened in hazardous areas.
• Before putting the Memocheck Sim CYP03D into operation, make sure that the battery
compartment is closely securely with a screw.
• Ex-rated digital sensors and simulators with Memosens technology are indicated by an
orange-red ring on the plug-in head.
• The maximum permissible cable length is 100 m (330 ft).
• Full compliance with regulations for electrical systems in hazardous areas (EN/IEC
60079-14) is mandatory when using the devices and sensors.
• The conductive protective coating on the device is part of the Ex-related safety concept.
Make sure there is no damage >4 cm 2on the protective coating.
Type 1 Type 2
Manufacturer Duracell Plus batteries Energizer
Type MN1500 EN91
Designation LR6 (IEC) LR6 (IEC)
Ubattery, nominal 1.5 V 1.5 V
Chemical composition Zinc/manganese dioxide (Zn /
MnO2)
Zinc/manganese dioxide (Zn /
MnO2)

CYP03D Device description
Endress+Hauser 7
3Devicedescription
3.1 Measuring system
Sensor simulation in a complete measuring system consists of:
•MemocheckSimCYP03D
• Transmitter with Memosens technology
• Memosens data cable CYK10
a0014717
Fig. 1: Measuring system with Memocheck Sim CYP03D
1 Transmitter with Memosens technology, e.g. Liquiline CM44x
2 Memosens data cable CYK10
3 Memocheck Sim CYP03D

Device description CYP03D
8Endress+Hauser
3.2 IECEx
The approved digital Memocheck Sim CYP03D sensor simulator may only be connected in
IECEx-rated environments using the following IECEx-certified measuring cable:
1. CYK10-G*** (IECEx BVS 11.0052X)
2. It may also be connected using a Memosens measuring cable which has IECEx certification
and is identical both in terms of design, appliance technology and function.
Connection may only be established to the IECEx-certified intrinsically safe sensor output circuit
of the Liquiline M CM42 transmitter (IECEx TUR 11.0007X) or alternatively to an
IECEx-certified intrinsically safe Memosens sensor output that supports the following
maximum values. In particular, the effective inner inductance and the capacitance of the
approved, intrinsically safe sensor output may not exceed the values indicated below:
Electrical connection must be established in accordance with the wiring diagram.
3.3 ATEX
The approved digital Memocheck Sim CYP03D sensor simulator may only be connected in
ATEX-rated environments using the following measuring cable:
1. CYK10-G*** (BVS 04 ATEX E 121 X incl. amendments N9 and N9 amendment
information)
2. It may also be connected using a Memosens measuring cable which is identical both in
terms of design, appliance technology and function.
Connection may only be established to the ATEX-certified intrinsically safe sensor output circuit
of the Mycom S CPM153-G or Liquiline M CM42 transmitter or alternatively to an
ATEX-certified intrinsically safe Memosens sensor output that supports the following
maximum values. In particular, the effective inner inductance and the capacitance of the
approved, intrinsically safe sensor output may not exceed the values indicated below:
1. Entity parameters1)
1) Ex-relevant electrical connection parameters
2. Entity parameters1)
U0= 5.1 V U0= 5.04 V
I0= 130 mA I0= 80 mA
P0= 166 mW (linear output curve) P0= 112 mW (trapezoid output curve)
Ci= 15 FC
i= 14.1 F
Li= 95  Li= 237.2 

CYP03D Device description
Endress+Hauser 9
Electrical connection must be established in accordance with the wiring diagram.
3.4 Quick wiring guide in Ex areas
1. Entity parameters1)
1) Ex-relevant electrical connection parameters
2. Entity parameters1)
U0= 5.1 V U0= 5.04 V
I0= 130 mA I0= 80 mA
P0= 166 mW (linear output curve) P0= 112 mW (trapezoid output curve)
Ci= 15 FC
i= 14.1 F
Li= 95  Li= 237.2 
a0017245-en
Fig. 2: Connection in hazardous areas

Device description CYP03D
10 Endress+Hauser
3.5 Temperature classes
If the ambient temperatures shown above are not exceeded no invalid temperatures for the
particular temperature class will occur at the simulator.
Simulator Ambient temperature range TaTemperature class
CYP03D-**-** Memocheck Sim -20 to +50 ˚C (-4 to 122 ˚F) T4

CYP03D Incoming acceptance and product identification
Endress+Hauser 11
4 Incoming acceptance and product identification
4.1 Incoming acceptance
1. Make sure the packaging is not damaged!
Inform your supplier of any damage to the packaging.
Please keep the damaged packaging until any issues have been resolved.
2. Make sure the contents are not damaged!
Inform your supplier of any damage to the contents.
Please keep the damaged goods until any issues have been resolved.
3. Make sure the delivery is correct and nothing is missing.
Check the delivery against the delivery papers and your order.
4. For storage and transportation: pack the product in such a way as to protect it reliably
against impact and moisture.
Optimum protection is provided by the original packaging materials.
The permitted ambient conditions must be observed (see Technical data).
If you have any queries, contact your supplier or local sales center.
4.2 Product identification
4.2.1 Nameplate
The nameplate is located on the back of the device.
The nameplate provides you with the following information on your device:
•Ordercode
• Serial number
• Ex approval, if applicable
Compare the data on the nameplate with your order.
4.2.2 Serial number and order code
The order code and serial number of your device can be found in the following locations:
• On the nameplate
• In the delivery papers
• On the packaging
To establish the version of your device, enter the order code from the nameplate into the
search field at the following address:
www.products.endress.com/order?ident

Incoming acceptance and product identification CYP03D
12 Endress+Hauser
4.3 Scope of delivery
The delivery comprises:
• Memocheck Sim CYP03D
• Operating Instructions
• Quality certificate
• Cable as per order (optional)
• Case to store CYP03D and cable (optional)
• Certificate of calibration (optional)
4.4 Certificates and approvals
Declaration of Conformity
The product meets the requirements of harmonized European standards.
It therefore meets the legal specifications of EU guidelines.
The manufacturer confirms that the product has been successfully tested by applying the 4
mark.
IECEx
Ex ia IIC T4 Gb
ATEX
II 2G Ex ia IIC T4 Gb

CYP03D Operation options
Endress+Hauser 13
5 Operation options
5.1 Overview
5.1.1 Display
If an error message occurs, reset the device. If this action does not rectify the error, contact
your Endress+Hauser sales center.
5.1.2 Key functions
a0014911-en
Fig. 3: Display (Example: simulation mode)
1
2
3
4
5
6
Menu path and/or device designation
Battery status
Simulated parameter
Sim main value
Assignment of soft key, e.g.
Menu: Displays main menu
Enter: Confirms data entered
Assignment of soft keys, e.g.
"-/+": Configures numerical data
ENTER key
The ENTER key has the following functions:
• Switches on the device (press for at least 3 seconds)
• Calls up menu when in simulation mode
• Saves (confirms) data entered
• Selects a menu option
• Switches off the device (press for at least 3 seconds)
MINUS key and PLUS key
In setup mode, the MINUS and PLUS keys have the following functions:
• Configuration of parameters and numerical values
• Navigation through menu
In simulation mode, the MINUS and PLUS keys have the following functions:
• "Run through" of sim. main values, with each values being changed by the
amount of the delta value

Operation options CYP03D
14 Endress+Hauser
Escape function
Pressing the MINUS and PLUS keys simultaneously brings you up one level in
the menu.
Pressing the MINUS and PLUS keys for longer when in the main menu brings
you back to simulation mode.
MINUS key and ENTER key
Pressing the MINUS and ENTER keys simultaneously for longer allows you to
reset the device.
PLUS key and ENTER key
Pressing the PLUS and ENTER keys simultaneously for longer allows you to
reset the device to the factory settings.
This also deletes all the setups saved.

CYP03D Operation options
Endress+Hauser 15
5.2 Structure and function of the operating menu
5.2.1 Operating menu
Menu
Language
Display
Illumination
Contrast
Setup
Simulation
Parameter
Memosens
pH glass
pH + ORP
pH ISFET
ORP
Conductive cond.
Oxygen amper.
Chlorine
pH glass SIL
Fixed cable
Toroidal conductivity
Oxygen optical
Turbidity
Nitrate
SAC
Sim main value
Test values
Save setup
Load setup
Advanced
Date
Time

Operation options CYP03D
16 Endress+Hauser
Switch off auto.
Advanced functions
Calibration value
Error simulation
Ramp
Diagnostics
Diagnostic list
Order code
Serial number
Software
Hardware
Reset
Factory setting
Switch off
Menu

CYP03D Operation options
Endress+Hauser 17
5.2.2 Setting values
Changing values within the menu
Example: defining the start value of a ramp
Maximum and minimum values are displayed in the editor. You can only configure values within
these limits.
1. Use the arrow keys to select the digit of the value that you want to change.
2. Press to change the value.
The digit flashes.
3. Press or to increase or decrease the value.
4. Press to confirm your entry.
The "Escape" function ( and pressed simultaneously) is disabled here in order to
prevent incorrect entries.
5. Select the tick mark (arrow key) and press .
The edited value is accepted.

Commissioning CYP03D
18 Endress+Hauser
6 Commissioning
6.1 Switching on the measuring device
Switching on
Press and hold for at least 3 seconds.
This loads the last setup that was saved.
Switching off
Press and hold for at least 3 seconds.
6.2 Configuring the operating language and getting started
After switching off, it is necessary to carry out some settings in order to configure the most
important device functions. The following is an example.
Configuring the language
1. Press "Menu".
2. Select "Language" (using ).
Available languages (factory settings in bold):
•Deutsch
•English
•Français
•Español
• Italiano
3. Select your language, e.g. "Deutsch".
4. Confirm with .
From now on, you will be guided through the menu in the language of your choice.
Pressing and takes you back to the main menu.

CYP03D Commissioning
Endress+Hauser 19
Selecting a parameter and configuring test values
Available parameters:
•Memosens
–pH glass
–pH+ORP
–pHISFET
–ORP
– Conductive conductivity
– Oxygen amperometric
–Chlorine
– pH glass SIL
•Fixedcable
– Toroidal conductivity
–Oxygenoptical
–Turbidity
–Nitrate
–SAC
1. Under "Setup/Simulation", select the desired parameter, e.g. "ORP".
Press to confirm your entry.
Ranges of adjustment
•pHvalue:
-2.0 to 16.0 pH
•Temperature:
-40.0 to 150.0 ˚C
•Rawvalue:
-750.0 to 750.0 mV
• Raw value temperature:
-40.0 to 150.0 ˚C
• SCS resistance:
0.001 MOhm to 1.000 TOhm
2. Under "Setup/Simulation/Test values", enter the test values (see the section "Configuring
sim. main value and test values").
3. Press and simultaneously.
You are in the simulation mode.
You can now simulate the selected parameter using the selected settings.

Commissioning CYP03D
20 Endress+Hauser
Once you connect the Memocheck Sim CYP03D to a Memosens transmitter, the Memosens
symbol appears in the status line of the simulator.
It indicates that the simulator is communicating with the transmitter.
The simulation symbol displayed indicates whether or not the transmitter is in simulation mode:
• e.g. Liquiline CM442:
The symbol for simulation appears in the line of the simulated parameter.
• e.g. Liquiline M CM42:
The symbol for simulation appears in the status line.
You can connect the simulator to all transmitters using Memosens technology.
6.3 Configuring the measuring device
6.3.1 General settings
In the "Display" menu you can carry out the following settings:
• Illumination
•Contrast
Change the illumination or contrast setting of the display by pressing or . Confirm your
entry by pressing .
Path: Menu/Setup/Advanced
Function Configuration options
(factory settings in bold)
Info
To accept the configured value, use the arrow keys to go right until the check mark is highlighted.
Confirm with .
Date
Year 10
09 to 99
Set the current date.
Month 03
01 to 12
Day 28
01 to 31
Time
Hour 06
00 to 23
Set the current time.
Minute 30
00 to 59
Second 21
00 to 59