Eneo GLC-1401 User manual

1
Installation and Operating Manual
LAN Camera GLC-1401

2
Contents
1. Safety Instructions..............................................................................................................................................3
2. Product Features ................................................................................................................................................4
2.1 Product Introduction ...........................................................................................................................................4
2.2 General Description ............................................................................................................................................4
3. Description of the Front/Rear View......................................................................................................................5
3.1 Front Panel and Rear Panel.................................................................................................................................5
3.2 RS-232 Port & ALARM I/O...................................................................................................................................6
3.3 Flank Panel ........................................................................................................................................................7
3.4 The USB Function...............................................................................................................................................8
4. Installation..........................................................................................................................................................9
4.1 Connecting with an NVR .....................................................................................................................................9
4.2 Connecting with a DVR .....................................................................................................................................10
4.3 Connecting with a Multiplexer ..........................................................................................................................10
4.4 Updating System Software ...............................................................................................................................11
4.5 LAN CAMERA SD Card Troubleshooting.............................................................................................................12
4.6 Adjustment of Lenses.......................................................................................................................................13
5. Network Configuration......................................................................................................................................14
5.1 Cable Connections............................................................................................................................................14
5.2 Configure your LAN CAMERA Network Settings.................................................................................................16
5.3 TCP/IP Communication Software ......................................................................................................................17
5.4 TCP/IP Installation ............................................................................................................................................18
5.5 TCP/IP Configuration Setting.............................................................................................................................19
5.6 Connection Testing ...........................................................................................................................................20
6. Operating Instructions for Image Software and Network ...................................................................................22
6.1 Microsoft Internet Explorer................................................................................................................................23
6.2 The LAN CAMERA IP Surveillance .....................................................................................................................49
7. Advanced Operation .........................................................................................................................................66
8. Specifications...................................................................................................................................................69
9. Function of Client PC ........................................................................................................................................71
10 Dimensional Drawings......................................................................................................................................71
APPENDIX 1 - SCAN IP ..............................................................................................................................................72
APPENDIX 2 - LANCAM UPnP How To........................................................................................................................75
APPENDIX 3 - The ARP Function................................................................................................................................86
APPENDIX 4 - Register as a DDNS Member...............................................................................................................87
APPENDIX 5 - MPEG4 Bit Rate Lookup Table of LAN Camera.....................................................................................91
APPENDIX 6 - FAQ.....................................................................................................................................................92
APPENDIX 7 - Pin Assignment of the 30 Pin Main Connector of the Camera Packs
VHM LAN01, VHM LAN02, VHM LAN03 and VHM LAN04 ......................................................................93

3
1. Safety Instructions
• The instructions below must be followed for your own safety.
• Please read the safety instructions and operating instructions before connecting the device and putting it into
operation.
• Keep the operating instructions safe for use at a later date.
• Never operate the camera outside of the specifications as this may prevent the camera functioning.
• Never point the camera towards the sun with the lens open as this may prevent the sensor functioning.
• When laying the connection cable, it is essential to follow the instructions below: the cable must be laid in such
a way that it is not strained, bent or damaged and no moisture can penetrate.
• To prevent fire or shock hazard, avoid exposing this unit to rain or moisture.
• Do not block ventilation openings.
• Installation and maintenance of the system may only be carried out by persons with appropriate authorisation for
this and in accordance with the installation instructions - taking into account all the applicable standards and
guidelines.
• The installer is responsible for maintaining the protection class.
• Only use rust-proof screws should be used to mount the housing and camera outside.
• Do not place anything on top of the unit that might spill or fall into it.
• Only original spare parts from the manufacturer.

4
2. Product Features
2.1 Product Introduction
This user-friendly device combines cutting-edge sophistication with practical reliability and convenience, high perfor-
mance with smooth remote communication. Just plug in the network cable ! You’ll get live streaming Video & Audio
anytime any place ! You’ll have security you can rely on ! The especially high resolution has 480 TV lines, a built-in
web server and a Network interface to connect you with the Internet securely and fast.
Other special features include the masking of personal private images with flexible mask-area positioning and size,
the self-downloading automatic video codec and other components, and the whole unit is very easy to set up. You can
access the network to get smooth images through the real-time and synchronized audio / visual stream provided by
the device, because it supports two compression modes, the MJPEG and the MPEG4 - you can change from one to
the other as you wish. The MPEG4 file format is a very small size file, so it can save more images over a longer time
and can be set extremely fast. The device also has a built-in website server providing many Internet functions and
protocols, including the MDIX protocol which recognizes both the normal and the crossover cables, either of which
can connect up with a LAN camera.
We hope this device makes it easier for you to get your IP address information. This unit supports the USB interface
which helps you to very easily get an IP address to open the IE browser: Just type in your IP address to the browser
and you can access your LAN camera.
The device can hopefully provide the advanced motion detection function to improve your network surveillance with
both the powerful and enhanced multi-zone and multi-sensitivity modes of detection. We believe this unit is the right
answer to all your network surveillance problems. Try it and you’ll see.
2.2 General Description
• 1/3” CCD Colour Camera with C/CS Mount
• Horizontal Resolution of 480 TV Lines
• Automatic Shutter Control (AES)
• MJPEG and MPEG-4 Video Compression
• Simultaneous Video and Audio Signal Transmission
• E-Mail and FTP Transmission of Important Events
• Integrated Activity Detection
• Ethernet Interface: 10/100Base-TX
• Supports Various Network Environments
• Alarm In/Output, Audio Output
• Upgrade via SD Card, USB Interface and Network
• SD Socket for Local Video Storage by SD Cards

5
3. Description of the Front/Rear View
3.1 Front Panel and Rear Panel
Front Panel Rear Panel
1. Microphone:
The LAN CAMERA has an additional audio function. The device has a microphone built into its front panel which
records sound.
2. ALARM I/O & RS-232 Port:
The RS-232 communication port functions as a connector to an external control device. This port includes ALARM
OUT, GROUND, ALARM IN, and ALARM RECOVER for connecting with external devices.
WARNING: You can’t use general RS-232 cables to link up with the I/O connectors in the rear panel of
the device (please see the next page for further details).
3. VIDEO OUT Connector:
The connector provides the unit’s composite video signals to a monitor.
4. Plug Inlet:
A 5VDC inlet that connects to an external power supply.
5. ETHERNET 10/100 Connector:
This is a standard RJ-45 connector for 10/100 Mbps Ethernet networks.

6
3.2 RS-232 Port & ALARM I/O
1. RS-485 D-
2. RX: This pin is one of the RS-232 pins. It connects with the TX pin of another device.
3. TX: This pin is one of the RS-232 pins. It connects with the RX pin of another device. Please refer to the note
below on the standard RS-232 9 Pin Cable with Pin 2 and Pin 3 exchanged; see the pin configuration chart
below for details.
4. RS-485 D+
5. GND: Ground contact.
6. ALARM RESET (INPUT): This pin connects to an alarm-clear device for clearing an alarm. ( 5V, 20mA
0V(Active) )
7. ALARM IN (INPUT): This is an alarm input that can be programmed in the menu system to active low.
( 5V, 20mA
0V(Active) )
8. ALARM OUT (OUTPUT): This is an alarm output trigger. Connect this to external devices such as buzzers or
lights. ( 5V, 20mA
0V(Active) )
9. AUDIO OUT: This provides the unit’s audio signal to a speaker.
The pin configuration chart:

7
1. Lens Mount: This LAN CAMERA is used with either C or CS mount lens.
2. ALC VR: Iris control VR
When an auto iris (DC Drive) lens is used, this VR is used to adjust the iris for different lighting environments.
Adjust the VR clock-wise to open the iris and counter-clockwise to close the iris of the camera.
3. RESET: Recover to factory default.
4. IRIS: Auto iris connector
This camera works with a DC drive auto iris lens. Please refer to the pin assignment marked on the camera
when connecting the auto iris lens.
1. AES: Auto electric shutter
2. DC IRIS: Use auto iris (DC drive)
3. DHCP: Turn On / Turn Off use DHCP protocol. If the switch points upwards, the device can
change the setup of network function (enable/disable) via the network.
4. STATIC IP: If the switch points down, the device can’t obtain an IP address from the DHCP
server. This option is needed to configure the network communication settings.
3.3 Flank Panel
Right Flank Panel Left Flank Panel
1 2 3 4
CD – + + –
CONT DRIVE
5. DIP Switch:
6. POWER Indicator: Indicates the power status of the unit. The green light indicates the unit is activating.
The red light indicates the power is on and the SD card cannot be removed.
7. LAN Indicator: Indicates the LAN status of the unit. The green light indicates the 100 Mbps Ethernet network
is activating. The red light signals the LAN is data linking.
8. RS-485 Port: The RS-485 communication ports function as connectors when two or more units are serially
connected to an external control device.
9. 5 pin MINI USB Port: The user can use a USB device cable to connect the LAN CAMERA to the USB port on the PC.
10. SD CARD Slot: This is used for system software updating and archiving / accessing critical images.

8
3.4 The USB Function
By connecting the LANCAM with a PC via the USB connector, the LANCAM can provide two different functions.
1. Insert an SD card: As a card reader
Insert an SD card into the LAN CAMERA, then connect to the PC. You might transfer files between the SD card
and the PC. Once you’ve connected your LAN CAMERA to your computer, the Windows system will detect the
connection and ask you what you want to do with your SD card.
In another words, if the user connects the LAN CAMERA with an SD card and the PC via the USB connector, the
LAN CAMERA can be used as a normal card reader.
2. Remove an SD card: As a configuring tool
Before using the USB configuration setting page, please remember to remove the SD card or your PC will read
the SD card and won’t show this window.
Network
Setting
PPPoE
Setting
DHCP ON DHCP OFF
WARNING: After changing the settings, please click the „Apply” button. All of the options will be effective
after removing the USB connector.

9
4. Installation
Please follow the instructions and the diagram below to set up the system.
NOTE: The LAN CAMERA is linked by its Video Out connection via a BNC connector to a monitor’s Video In
connection. If this connection is there, you can see some information on the monitor screen, such as
the LAN CAMERA factory default Static IP address (192.168.1.168). But the LAN CAMERA Static IP
address can only appear if there is a connection between the LAN CAMERA and another device.
If there is no such connection, the LAN CAMERA factory default Static IP address will not appear on
the monitor screen.
4.1 Connecting with an NVR
Use a crossover LAN cable to connect directly to an NVR.
CONNECT TO ETHERNET
RJ-45 CONNECTOR
CONNECT TO
NVR ETHERNET PORT

10
CONNECT TO VIDEO OUT
BNC CONNECTOR
CONNECT TO DVR VIDEO IN
4.2 Connecting with a DVR
TO LAN Camera VIDEO OUT
BNC CONNECTOR
LAN CAMERA 1
LAN CAMERA 2
LAN CAMERA 16
4.3 Connecting with a Multiplexer

11
4.4 Updating System Software
If the system software of the LAN CAMERA needs to be upgraded, please take the following steps to safely process it.
Important: Before carrying out the following procedures, please ensure the SD card is working and the file
of system firmware is intact.
1. Format an SD card using the FAT16 format if it is unformatted; there are no limitations to an SD card’s capacity.
2. Create a directory named LANCAM in the SD card if it does not exist.
3. Copy the file of UPDATE.BIN to the LANCAM-directory.
4. If the LANCAM is running, please power it off first.
5. Insert the SD CARD into the LANCAM.
6. Remove the Ethernet cable from the RJ-45 port and then power on the LANCAM.
7. In 5 to 10 seconds, a message reading „UPDATE PROCESSING” will show up on the screen on a blue back-
ground; if not, please check out steps 1 to 6 carefully or else inform your technical support while ignoring the
following steps.
8. DO NOT power off the LANCAM while this update process is running until the message „UPDATE OK RESET
PLEASE” appears on the screen; it might take 15 to 30 seconds to appear.
9. If the message „UPDATE NG RESET PLEASE” appears rather than „UPDATE OK RESET PLEASE”, please write
down the error messages shown on the screen and inform your technical support, while ignoring the following
steps.
10. Power off the LANCAM when this update process is finished, then remove the SD card from the LANCAM.
11. Reconnect the Ethernet cable to the RJ-45 port if necessary.
12. Power ON the LANCAM and it will work normally if the entire update procedure goes correctly.
13. Verify the version of the system software.
WARNING:
1. Don’t use FAT32 or NTFS or other file formats in step 1.
2. Steps 1 to 3 have to be done on a PC.
3. Make sure the file of UPDATE.BIN is a correct one in step 3, or the LANCAM will not work normally after
being updated.
4. If the power of the LANCAM is suddenly lost in step 8, please remove the SD card first and turn on the
LANCAM next to test its operation. If the LANCAM remains working normally, please go back to step 4;
otherwise, please inform your technical support.
5. In step 10, if the SD card is not removed and the LANCAM does not get online as well, the updating
process must be repeated again after rebooting the LANCAM.
6. Make sure that the SD card is inserted in a correct position in step 5, or the LANCAM will suffer
permanent physical damage.
7. If the message „CSUM ERROR” appears in step 8, it implies a problem in the file of UPDATE.BIN.
8. Don’t interrupt the process while the unit is updating itself; proceed with an SD card not including any
system software of the unit, or else the unit will crash.

12
4.5 LAN CAMERA SD Card Troubleshooting
1. Check if the SD card position is correct or not. Please refer to the manual for the related information.
2. After powering the LAN CAMERA on, correctly insert the SD card, and a little icon of „SD” will show up in the
upper-right corner of the monitor screen. If not, it means the device detection has failed. Please contact your
technical support and ignore the following steps.
3. If no cross sign appears beside the „SD” icon, please go on to the next step. If a cross sign appears, please
check the following:
a. Is it really an SD „Memory” Card?
b. Is this SD card formatted in the FAT16 format?
c. Connect the SD card with a PC and test to see whether the PC can read the data or not.
d. Does this SD card still have the capacity for storing data?
e. Is the SD card set to write?
If all the answers are „yes” but the cross sign still persists, please contact your technical support and ignore
the following steps.
4. Please make sure the function of „SD CARD ENABLE” is activated in the ALARM and SCHEDULE pages if no
cross sign appears beside the „SD” icon on the screen.
5. After recording, read the data on the web page of „sdget.htm”. If the data cannot be read through the network,
please read it instead in a PC, check the data stored in the „LANCAM” directory and contact your technical
support regardless of whether there is data or not.
WARNING:
1. Performing this troubleshooting process may need a monitor, a PC, a card reader and some cables.
2. If the SD card is removed while storing or accessing data, the data will be lost.
3. If there is a cross sign beside the „SD” icon, it means the SD card has been inserted into the
LAN CAMERA but cannot perform its writing function. Possible reasons are:
a. It is not an SD memory card.
b. The SD card is unformatted or formatted in a non-FAT16 or non-FAT12 format.
c. The file system is damaged.
d. The capacity of the SD card is full.
e. The SD card is set to be read only.
4. Turn off the power before inserting the SD card. Otherwise the unit may shut down.

13
L
M
AL
KM
L
C mount lens
CS mount lens
4.6. Adjustment of Lenses
Adjustment of flange
focus for fixed focus
lenses
This adjustment (distance between lens casing and sensor surface) is required if a sharp
definition cannot be obtained with the lens focussing, or in order to adjust the ∞position
To obtain a sharp definition, point the camera at an object which is at least 2000 times
further away from the front of the lens than the focal length. (If the focal length is 7.5mm,
the object must be at least 15m distant from the camera).
Open the aperture fully and set the focus to ∞(infinite).
If the lens has automatic exposure control, select a dark object, or better use an ND filter
(64-x) to ensure that the aperture is fully open.
Undo set screw M. Turn the lens with the CS mount connection until the definition is sharp.
When finished, retighten screw M.
Adjustment of flange
focus for variable
focus lenses
To obtain a sharp definition, point the camera at an object which is at least 5 times the
minimum lens distance (MOD) of the lens. (If this is 1m, the object must be at least 5m
distant from the camera).
Open the iris fully and set the lens to the maximum tele position and focus with the focus
ring.
If the lens has automatic iris control, select a dark object (or use an ND filter, 64-x)
to ensure that the iris is fully open.
Set the lens to the maximum wide-angle position.
Undo set screw Mand turn the C/CS ring on the camera until an optimal sharpness is
reached. Repeat the process for checking purposes, if necessary.
When finished, retighten screw M.
Note The value stated in the diagram as AL (depth of thread of the lens with CS mount:
<- 5mm) must be observed. The camera may be damaged if this value is exceeded.
When installing a lens with CS mount, never use the C-mount adapter ring.
Addition when using
cameras for day/
night application
Even if the lens is IR corrected (0-focus shift), a minor flange focus is possible between
visible light and IR light.
If there is a day/night application with IR illumination, the flange focus should be set under
IR light conditions. This is because the iris is generally opened when used at night due
to the poor level of light and low depth of focus. During the day, the iris is continuously
closed further, there is a greater depth of focus and the difference in the flange focus is
compensated.

14
Explanation of terms for iris setting
AGC (automatic gain
control)
This starts tooperate when the light intensity is insufficient to deliver a full video signal
(1Vp-p). The greater the gain, the greater the signal noise in the picture. It is generally
activated between 0.8 and 1.0Vp-p.
White clip Signal limitation at high image amplitudes. The white clip value generally lies between
1.1 and 1.2 Vp-p.
AES (automatic
shutter control)
This automatically controls the shutter times, it starts when the light intensity becomes
stronger and the signal would otherwise be limited/over-regulated by the white clip
feature. Automatic shutter control is mainly applied for manual lenses.
If a camera is operated with controlled lenses, regardless of whether DC or AI, the AES
must be switched off. Problems arise if this is not done because both control systems
try to steer the volume of light for the camera. As the AES generally reacts faster, the iris
remains fully opened and the shutter resumes the control work, which produces major
drawbacks. As the iris is open, the depth of focus is very low. When shutter times are
short, this can cause a smear effect (bright, vertical stripes in light parts of the picture).
Iris adjustment The working point of the iris should always be above the AGC start and below that of the
white clip. This range is very small with some cameras, making it difficult to adjust the
lens. It is therefore advisable to switch off the AGC (if possible) when adjusting the iris.
Once the lens has been focussed, the AGC must be switched back on (only for cameras
which allow the AGC to be switched off).
In the case of DC lenses, the working point of the iris is adjusted at the camera’s level
potentiometer (the AI amplifier is built into the camera).
In the case of AI lenses, the level potentiometer is located on the lens (the AI amplifier is
built into the lens).
5. Network Configuration
5.1 Cable Connections
Please follow the instructions below to connect your LAN CAMERA to a computer or a network and to choose a proper
RJ-45 cable configuration for connections.
Physical specification of RJ-45 cable for Ethernet
Wire Type Cat. 5
Connector Type RJ-45
Max. Cable Length 100m
Switch/Hub Wiring Configuration Straight Through
PC Wiring Configuration Cross Over

15
5.1.1 Connect to a Computer
Use a crossover LAN cable to connect directly to a computer.
CROSSOVER CABLE PIN CONFIGURATION
CROSSOVER CABLE
TO PC LAN CARD
5.1.2 Connect to a LAN Hub (INTRANET)
The RJ-45 PIN configuration for connecting with a LAN Hub is shown below.
TO NETWORK
TO PC NETWORK CARD
HUB/Switch / Router

16
5.2 Configure your LAN CAMERA Network Settings
Upon connecting with the network hardware, you need to activate the network function and configure the proper
network settings of the LAN CAMERA.
5.2.1 Enable DHCP Function
This function can only work if the LAN, which the unit is connected to, has a DHCP server. If the DHCP server is
working, please move the dip switch points up to 3 on the flank panel; now the LAN CAMERA will obtain an IP address
automatically from the DHCP server. In that case, please skip section 5.2.2 (Set IP address) and follow section 5.3
(TCP/IP Communication Software).
5.2.2 Set IP Address
You need to set an IP address for the unit if the LAN unit isn’t connected to a DHCP server. Otherwise, please follow
the instructions given below:
Set the IP, SUBNET MASK and GATEWAY. The following is a sample setting.
IP: 192.168.1.X
SUBNET MASK: 255.255.255.0
GATEWAY: 0.0.0.
NOTE: When only one unit of the LAN CAMERA is connected to a computer or LAN, you can freely assign
an IP address for the LAN CAMERA. For example, there are a range of LAN CAMERA IP addresses from
192.168.1.1 to 192.168.1.255. You can pick one for use from the range of the IP. It’s not necessary
to set MASK and GATEWAY; leave the settings as default.
When a LAN CAMERA is connected to a WAN, you must acquire a unique, permanent IP address and
correctly configure the MASK and GATEWAY settings according to your network architecture.
If you have any questions regarding those settings, please contact a qualified MIS professional or
your ISP.
NOTE: When connecting to a network, each connected LAN CAMERA must be assigned a unique IP, which
must be in the same class type as your network address. IP addresses are written as four sets of
numbers separated by periods; for example, 192.168.1.1 Therefore, if the connected network is
identified as Class C, for example, the first three sets of numbers of the LANCAMERA IP address must
be the same as the network address. If the connected network is identified as Class B, the first two
sets of numbers of the LAN CAMERA IP address must be the same as the network address. If you have
any questions regarding these settings, please contact a qualified MIS professional or your ISP.

17
5.3 TCP/IP Communication Software
Follow the instructions below to install the TCP/IP communication program into your computer.
Click the Start menu from your computer, and point to the Settings/Control panel.
Double click the Network icon to enter the windows.

18
Click the Configuration tag, and check if the TCP/IP is included among the network components list. If the TCP/IP is
included, please process section 4.5. If it is not included, please follow section 4.4 to install the TCP/IP.
During the installation, you will be requested to insert the Windows CD-ROM. After installation, the PC may be restarted.
5.4 TCP/IP Installation

19
5.5 TCP/IP Configuration Setting
Click Start –> Settings –> Control Panel –> Network
Select TCP/IP, and then click Properties.
Before processing the LAN CAMERA installation in a WAN, please make sure the Internet connection works properly.
If not, please contact your ISP provider.
If you are using a DHCP server, please select Obtain an IP address automatically. Any assigned IP address for the
connected LAN CAMERAs must be in the same class type as the server. If there is no DHCP server, please select
specify an IP address and type in the IP address of your PC. This IP address must be different from the LAN CAMERA
IP but in the same class type.
NOTE: The IP address of a LAN CAMERA in a network must be unique to itself as opposed to those of the
other chosen PCs, but in the same class type.

20
5.6 Connection Testing
With the previous settings, follow the instructions below to ensure whether you have established the connection
successfully.
Click Start –> Programs –> MS-DOS Prompt
Type in ping 192.168.1.168 then Enter. (See the sample screen below)
• This IP is the LAN CAMERA IP address that is assigned for the connected LAN CAMERA in step 2.