Eneo MSM-42F0037MPA User manual

EN
User Manual
1/2.8” HD Board Camera, Colour,
1920x1080, WDR, 12VDC
MSM-42F0037MPA
MSM-42F0028M0A

Safety Precaution
03
ULTRA CLEAR RESOLUTION CAMERA
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.

ULTRA CLEAR RESOLUTION CAMERA
Safety Precaution
04
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.

ULTRA CLEAR RESOLUTION CAMERA
Contents
05
Safety Precaution
p.03~04
Contents
p.05
Features
p.06
Composition
p.07
Dimensions
p.07
p.08~09
Installation Instructions
p.10~24
Operating Instructions
Specifications
p.25

ULTRA CLEAR RESOLUTION CAMERA
Features
Key Features
06
• Full-HD 2Mega pixel, HD-SDI/EX-SDI CAMERA, 1920x1080(30p/25p)
• The best low light performance with 1/2.8” SONY’s STARVIS sensor
• Video output EX-SDI 1.0,2.0 / HD-SDI / TVI mode / AHD mode /
CVI mode or CVBS Selectable
• TVI mode / AHD mode / CVI mode, Video Transmission Distance
over Coax.; 500M
• Lens selectable
> MSM-42F0037MPA : f=3.7mm Pin-hole lens
> MSM-42F0028M0A : f=2.8mm Fixed lens
• Sensitivity of Color 0.08 Lux, B/W 0.005 Lux
• True WDR(Wide Dynamic Range) 30/25fps
• ROI (Region of Interest) WDR mode:
- Proper compensation of exposure for each inside and outside of
interested area.
- Better contrast and No motion ghost effect
• Improved Noise figure with the enhanced 3DNR
• Motion Detection, Privacy Mask, Defog, Sens-up(~x32), D-WDR,
Sharpness, Mirror/Flip, BLC/HLC, Title Set
• Top performance at low light sensitivity (Sens-up On)
• Selectable Digital output 1080p or 720p
• OSD Menu & Video Sub-out port for easy installation & maintenance
(Available by mini jig OSD control board only)
• Remote control through Pelco-C(UTC/HD-TVI), Hikvision
• Circuit protection against faulty connection in power polarity
• Power: DC12V

07
Composition
Dimensions
ULTRA CLEAR RESOLUTION CAMERA
(unit : mm)
Operating
Instruction
Mounting Screw:
BH 3x10mm (2pcs)
Mini JIG
OSD Control board
MSM-42F0028M0A
MSM-42F0028M0A
MSM-42F0037MPA
MSM-42F0037MPA
42
45.7
37.8
37
42
45.7
37.8
37
43.5
21.5
49
27

ULTRA CLEAR RESOLUTION CAMERA
Installation Instructions
08
• Care should be taken the cable is NOT to be damaged, kinked or exposed in
the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun or
spot light.
CAUTION
Mounting Screw
BH 3x10mm
Power/Video Cable
Bracket
OSD Controller
Connector
Power
Connector
Video
Connector
1. Place the camera bracket at the installation position and fix it by using
mounting screws.
2. Connect the power/video cable then setup the camera menu if neccessory.
(Use the mini jig OSD control board)
3. Adjust the camera’s viewing angle (Tilt, Rotation)
[ REAR VIEW ]
TILT
ROTATION

ULTRA CLEAR RESOLUTION CAMERA
Installation Instructions
09
Power Supply Connections
Camera can be operated with the regulated or unregulated 12VDC but
the regulated power supply of 12VDC is recommended.
Camera is protected from the damage by the reverse connection of polarity.
※SDI OUTPUT
(Yellow)
ANALOG OUTPUT
(Black)
POWER ( )
※Please use the cable as provided with camera. If camera cable is cut
and re-wired, the transmission distance of video can be reduced.
Especially SDI cable should not be cut because it requires detailed
wiring job and affects the transmission distance.

ULTRA CLEAR RESOLUTION CAMERA
Operating Instructions
10
OSD menu Table
Camera setup menu can be accessed and controlled by OSD controller.
ANALOG OUT0, ANALOG OUT1, SDI OUTPUT
MENU SUB MENU CONFIGURATION
LENS
FOCUS Ast.
EXPOSURE
BACKLIGHT
DC
MANUAL
ON, OFF
MODE (INDOOOR, OUTDOOR, DEBLUR)
0~20
WEIGHT
MODE ROI WINDOW ZONE/USE,
H/V-POS, H/V-SIZE
NORMAL
OFF
HLC LEVEL, COLOR
H/V-POS, H/V-SIZE
BLC
WDR
COLOR
DAY & NIGHT
3D-NR
IMAGE
AWB
COLOR GAIN
EXTERN
AUTO
COLOR
B&W
SHARPNESS
GAMMA
SMART IR, ANTI-SAT., D>N THRES, N>D THRES, DELAY
SMART IR, ANTI-SAT., AGC THRES, AGC MARGIN, DELAY
SMART IR, ANTI-SAT.
AUTO, AUTOext, PRESET, MANUAL (C-TEMP, R/B-GAIN)
OFF, LOW, MIDDLE, HIGH
0.45, 0.55, 0.65, 0.75
MAIN OUTPUT
ANALOG OUT0
ANALOG OUT1
SDI OUTPUT
AHD MODE, CVI MODE, TVI MODE, CVBS
CVBS, TVI MODE, OFF
HD-SDI, EX-SDI 1.0, EX-SDI 2.0, OFF
BRIGHTNESS
SHUTTER
SENS-UP
AGC
0~20
AUTO
MANUAL
(SPEED)
FLICKERLESS
1/25, 1/50, 1/100, 1/200, 1/400, 1/800,
1/1600, 1/3200, 1/6400, 1/12800, 1/25600
0~10
OFF, x2, x4, x8, x16, x32
OFF, ON
MIRROR
• EXIT : Enters ‘EXIT’ menu with save current setting or without save.
• RETURN : Returns to the previous menu.
TARGET-BRT LOW, MIDDLE, HIGH
LOW, MIDDLE, HIGH

ULTRA CLEAR RESOLUTION CAMERA
Operating Instructions
11
DEFOG
D-WDR
MODE (AUTO, MANUAL)
LEVEL (LOW, MIDDLE, HIGH)
OFF, LOW, MIDDLE, HIGH
OFF, ON
OFF, ON
FLIP
MOTION OSD
TEXT ALARM
SYSTEM
EXIT
OUTPUT
RESOLUTION
TV SYSTEM
SAVE, CANCEL
CAM TITLE
RESET
LANGUAGE ENG, CHN(S), CHN, JPN, KOR, GER
OFF, ON
SDI OUTPUT
ANALOG OUT0
HD-SDI, EX-SDI 1.0, EX-SDI 2.0, OFF
AHD MODE, CVI MODE, TVI MODE, CVBS
1080 25P, 720 25P, 720 50P(Cropped)
US(NTSC), EU(PAL)
DET WINDOW
DET TONE
MDRECT FILL
SENSITIVITY
OFF, ON
OFF, ON
OFF, ON
0~10
0~4
WINDOW ZONE, WINDOW USE, DET
H/V-POS, DET H/V-SIZE
MOTION
OFF, RIGHT UP, LEFT DOWN
ON
IMAGE
PRIVACY ZONE NUM, ZONE DISP, H/V-POS, H/V-
SIZE, Y LEVEL, CB/CR LEVEL, TRANS
OFF, ON
If CVBS video is enabled through ANALOG OUT0 or Sub-out port, WDR
and 3D-NR functions are disabled in all video outputs.
It should be considered when installer adjusts the video with installation
monitor via CVBS video signal.