Eneo PXB-2080MIR B User manual

Quick Installation Guide
Mega Pixel Network Camera
PXB-2080MIR B

Safety Precaution
03
FULL-HD NETWORK CAMERA
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

Safety Precaution
04
FULL-HD NETWORK CAMERA
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual appearance of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.

Contents
05
FULL-HD NETWORK CAMERA
Safety Precaution
p.03~04
Contents
p.05
Features
p.06
Composition
p.07
Dimensions
p.08
Part Names
p.09
Installation Instructions
p.10~12
Operating Instructions
p.13~26
Specifications
p.27~28

Features
Key Features
General Description
06
FULL-HD NETWORK CAMERA
• Full HD, WDR, NETWORK CAMERA 1920 x 1080/30p(25p)
• ONVIF S & PSIA Conformance
• True Wide Dynamic Range
• Built-in Mega Pixel Vari-focal Lens (f=2.8~10mm)
• DUAL Filter Switcher
• Improved Noise figure with the enhanced 3D-NR
• Intelligent Focus Indicator on Screen which helps to get the sharpest focus.
• Pointing Zoom which enables the flexible zooming at any area.
• Smart Motion Zoom in combining with Pointing Zoom.
• Motion Detect, Privacy Mask, DeFog, Sens-up(x8), BLC/HLC, D-Zoom(1.1x~8x)
• H.264 / MJPEG dual streaming
• Slot for Standard SD memory card up to 32GB
• Two way Audio & Alarm input /output
• Menu Control via either Local Joystick or WEB
• External Zoom & Focus Adjustment
• OSD MENU & Video Sub-out port for easy installation & Maintenance
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• IR-LED 40pcs.
• PoE(IEEE Std. 802.3af)
• IP 67 Protection
• Dual Window
• One touch 3-Axis bracket
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accept the infrared light
• With PoE as well as 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
• With Intelligent Focus Indicator and FOCUS ADJUST menu,
- Offers easy adjustment of sharp focus
- Eliminates the mistake of the erratic focus adjustment

Composition
07
FULL-HD NETWORK CAMERA
Torque Wrench:
3mm (1pc)
Video Sub-out Cable (1pc) Coupler for
RJ45 Cable (1pc)
Assembly Screw:
4 x 14mm (4pcs)
Mounting Screw:
4 x 30mm (4pcs)
Plastic Anchor:
6 x 30mm (4pcs)
Mounting Template
Easy Bracket
Operating InstructionNetwork Camera
EMI Ferrite Core (1pc)

Dimensions
08
FULL-HD NETWORK CAMERA
(unit : mm)
267
108
87.30
100
86.40
75.90
80
190

Part Names
09
FULL-HD NETWORK CAMERA
DUAL WINDOW
ETHERNET &
POWER CABLE
SUNSHIELD BOLT
REAR
VIEW
SUNSHIELD
FRONT CASE
EASY
BRACKET
OSD Setup
CONTROL COVER
BRACKET
REAR CASE
FOCUS ZOOM

• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken the cable is NOT to be damaged, kinked or exposed in the
hazardous area.
• Do not expose the camera directly to a strong light source such as the sun or spot
light.
Installation Instructions
10
FULL-HD NETWORK CAMERA
Torque Wrench
Assembly Screw
: 4x14mm
Mounting Screw
: 4x30mm
1. Locate the mounting template at the installation position and drill the ceiling or wall if
needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and fix it through using mounting screws
(4x30mm). Skip this step when an easy bracket is not installed.
3. Route the Ethernet & Power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Fix the camera bracket through using assembly screws (4x14mm).
5. Set the camera’s viewing angle and adjust zoom/focus of lens by using the torque wrench.
6. Put the sunshield to the camera unit and tighten the sunshield-bolts.
CAUTION
REAR VIEW
1
2
3
4
Cable exit