Eneo VK-1322 User manual

1
Instruction Manual
B&W Smoke-Detector Hidden Camera
VK-1322/SMD

2
3
Contents
1. Safety Instructions ......................................................................................... 2
2. Description .................................................................................................... 3
3. Installation ..................................................................................................... 3
4. Specications ................................................................................................ 5
5. Dimensional Drawings ................................................................................... 6
1. Safety Instructions
• Read these safety instructions and the operation manual rst before you install
and commission the camera.
• Keep the manual in a safe place for later reference.
• Contact your local dealer in case of malfunction.
• Protect your camera from contamination with water and humidity to prevent it
from permanent damage.
Never switch the camera on when it gets wet. Have it checked at an authorized
service center in this case.
• To disconnect the power cord of the cameras, pull it out by the plug.
Never pull the cord itself.
• Do not open the camera housing.
Maintenance and repair have to be carried out only by authorized service centers.
• Operate the camera only at a temperature range of -10°C to +50°C and at
a humidity of max. 90%.
• The camera is equipped with an automatic gain control (AGC) which increases
the sensitivity at low light levels.
Noisy pictures at these conditions are quite normal.
• Pictures including bright spotlights will cause perhaps vertical lines (smear) or
soft edges (blooming) on the monitor display. This happens most probably in
automatic shutter mode (AES).
This is not a defect but an effect caused by the CCD sensor.

2
3
• Use only a mild detergent to clean the housing.
Never use dilution or gasoline for this can cause permanent damage to
the surface.
The cameras should never:
• be operated beyond the technical specications. This can lead to destruction.
• pointed with open iris towards the sun. (This can damage the sensor).
Note: This is a class A digital device. This digital device can cause harmful
interference in a residential area; in this case the user may be required
to take appropriate corrective action at his/her own expense.
2. Description
This B/W (Colour) Smoke-Detector Hidden Camera uses a high sensitive 1/3”
interline transfer CCD Image Sensor (CCD = Charge Coupled Device), and all state
circuitry which provides extremely long life and high reliability.
This Camera offers excellent image quality and functions with low lag and high burn
resistance, and is not subject to distortions from magnetic elds.
Highly resistant to shock and vibration and easy to install, this Camera is an
excellent choice for your B/W CCTV system.

4
5
3. Installation
1. Select a location in the ceiling where you want to install the camera unit.
2. Connect the cables as follows: 12VDC to A , Video Out to B. (Ref. Figure below)
3. With your hand, position the camera unit so the camera is aimed toward the
area to be observed.
4. While holding the unit in position, re-check the camera’s horizontal sighting
to ensure the unit‘s position is correct as placed in Step 1. (Ref. Figure below)
5 If it is necessary to adjust the vertical view angle, do the following - Loosen
screw D with a screwdriver. Turn the Camera Board C to the desired angle
(you may use a portable monitor or communicate with the Master Control
Room to make sure the view angle is correct).
Tighten screw D to secure the vertical view angle. (Ref. Figure below)
Step 2
Step 5
Step 4
35° max.

4
5
6. To secure the unit in the location selected in STEP 1, tighten the screws E
in the holes as shown in Figure below.
Step 6

6
7
4. Specications
Model VK-1322/SMD
EDP No. 91988
Imager 1/3” Sony Super HAD Interline Transfer CCD
Picture elements Approx. 440,000 (H) 752 x (V) 582
System CCIR
Synchronization Internal
Sensitivity 0.65Lux at F2.0 / 0.23Lux at F1.2
(VT measured result)
Horizontal resolution 600 TV lines
Signal-to-noise ratio 48dB (AGC OFF)
Automatic gain control (AGC) Supplied
Automatic shutter control (AES) 1/50 ~ 1/100,000sec.
Gamma correction 0.45
Lens F2.0/3.7mm pinhole
Horizontal angle of view 68°
Vertical tilt range 0° ~ 35° (ceiling as reference)
External connections Video (BNC), 12VDC (DC socket)
Video output 1Vp-p, VBS, 75ohms
Supply voltage 12VDC ±10%
Power consumption 1.4watts
Temperature range -10° ~ +50°C
Housing Plastic
Mounting Wall and drop ceiling mount
Colour Light grey
Dimensions See drawing
Weight 110g

6
7
5. Dimensional Drawings
60
∅ 50
∅ 120
Dimensions: mm
Accessories
EDP No. Description
70447 Plug-in Power Supply Unit 100-240VAC
77772 PSU 12VDC/0.5A, Regulated, Desktop
77779 Plug-in Power Supply Unit 230VAC/12VDC

8
Technical changes reserved
© Copyright by VIDEOR TECHNICAL 03/05
eneo® is a registered trademark of Videor Technical E. Hartig GmbH
Exclusive distribution through specialised trade channels only.
VIDEOR TECHNICAL E. Hartig GmbH
Carl-Zeiss-Straße 8 · 63322 Rödermark/Germany
Tel. [phone] / 888-0 · Fax [phone] / 888-100
www.videortechnical.com