Energizer EZLSPB10 User manual

©2019 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related
subsidiaries and are used under license by Builder SAS.
All other brand names are trademarks of their respective owners.
Neither Builder SAS nor Energizer Brands, LLC is affiliated with the respective owners of their trademarks.

Thanks for choosing the EZLSPB10 Series!
You're excited to power up, so we'll keep this brief. Let's get started!

CAUTION:
Read instructions and warnings before operating!
SAVE THESE INSTRUCTIONS! READ ALL INSTRUCTIONS!
SAFETY INSTRUCTIONS
WARNING: To avoid serious injury or death from electrical shock or fire:
1. DO NOT handle this fixture or try to plug it in when your hands are wet or damp or when standing on a wet or
damp surface or in water.
2. This fixture MUST ALWAYS BE USED IN ACCORDANCE WITH ALL ELECTRICAL AND SAFETY CODES AND
ORDINANCES.
3. ALWAYS make certain that the power source conforms to the rating on the fixture.
4. ALWAYS disconnect the power before servicing or inspecting the fixture for any reason.
5. This fixture is suitable for indoor/outdoor use. The fixture can be used outdoors in rain or damp conditions.
6. CAUTION: RISK OF ELECTRICAL SHOCK. Do not use in or near standing water, or where water may accumulate.
Keep this fixture at least 16 feet from pools or spas.
7. DO NOT use in potentially dangerous locations, such as in flammable or explosive atmospheres.
8. NEVER operate the light with the clear protective glass broken or removed.
9. NEVER LOOK DIRECTLY INTO LIGHT SOURCE. LEDs are extremely bright and can damage eyes with prolonged
exposure.
10. KEEP AWAY from heating vents, radiators, or other sources of heat.
11. Turn off the light before charging to avoid the battery life reduced.
12. Do not use alcohol, flammable solutions or other solvents nearby or for cleaning of the warning light. Only clean
the warning light with warm water and a soft cloth.
13. Supervise children when using the warning light.
14. The warning light is waterproof when used in accordance with manufacturer’s instructions.
15. For damage caused by abnormal use, the user should be responsible for it.
16. A li-ion battery cell is included in this fixture. DO NOT replace the battery cell yourself. It should be serviced by a
qualified repair person using only identical replacement parts. This will ensure the life of the fixture is maintained.
17. In rare circumstances, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, immediately seek medical help. Liquid ejected from the battery may cause
irritation or burns.
18. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery pack.

SPECIFICATIONS
•Power: Max. 10W
•Degree of protection: IP44
•Material: Aluminum die-casting
•Color temperature: 6000K
•Luminous Flux: 250lm
•Beam angle: 120 degree
•Running time: 3 hours
•Charging time: 4 hours
9. AC/DC adaptor (UK)
9. AC/DC adaptor (VDE)
1. Handle
2. Fix screw
3. U-shape bracket
4. Stand bracket
5. Power switch
6. Power socket
7. LED indicator
8. Stand bracket fix screw
9. AC/DC adaptor
1
2
3
4
5
6
8

Luminaires equipped with non-replaceable LED modules.
Model Name
Other
EZLSPB10
/EZLSPB10UK
3.7 V D.C. Max. 10 W, Class III, IP44
LED chip is non-replaceable and cannot be changed, it
is powered by a lithium battery inside. Battery
manufacturer: Changhong Sunpower Co.,Ltd
Li-ion Battery
3.7V D.C. 2200mAh
Battery manufacturer: Changhong Sunpower Co.,Ltd
Battery
chargers
XH0420-1000WG
XH0420-1000WE
Input: 100-240 V ~, 50/60 Hz, 0.3 A
Output: 4.2 V D.C., 1000 mA
Approved Cl.II, IP 20 independent isolating battery
charger, manufacturer: Xiamen Xunheng Electronics
Tech Co.,Ltd
ASSEMBLY INSTRUCTIONS
Fasten the light to the Stand Bracket (4) with the Stand Bracket Fix Screw (8) as shown and tighten. Note the round washer located on top of the
U-shape Bracket (3).Fasten the light to the “H” Stand (4) with the Knob (8) as shown and tighten. Note the round washer
located on top of the Bracket (3).
4
8
3

OPERATION
Press the switch ‘I’, the work light will be ON.
Press the switch ‘O’, the work light will be OFF.
To recharge, plug the charging cable as shown below.
Note: Recharge only with the charger specified by the manufacturer.
Loosen the knobs on sides to adjust the angle of the light head to aim light where needed. Retighten the knob to secure
position.

Loosen the knobs on the base to adjust the rotation of the light head to direct light where needed. Retighten the knob
to secure position.
LAMP REPLACEMENT
The LED chip in this fixture is not replaceable. It will last up to 50,000 hours and is not subject to breakage due to shock
like typical halogen or incandescent lamps.
MAINTENANCE
Remove dirt and grime as soon as it accumulates. Use a soft, damp cloth and mild soap, if needed.
NEVER submerge any part of the work light in any solution to clean it.
DO NOT USE solvents (such as gasoline, turpentine, etc.) to clean the work light.