Energotech EnergoControl T60-EW User manual

EnergoControl
Touchscreen Thermostat T60-E and T60-EW
Step 1
Release the front half by loosen the screw from the boom of
the thermostat. Then carefully pull and separate the front part
away from the back-plate, inially from the lower part of the
thermostat.
Step 2
Place the front part of the thermostat in a safe place, to prevent
scratches and damage. Connect the wires in accordance with
the diagram on page 2. The wiring diagram must be followed.
Step 3
Screw the thermostat back-plate onto the recessed juncon box
in the wall. Use the supplied screws or the original screws of the
juncon box.
Step 4
When the back-plate is secure, ret the front part carefully to
the back-plate, starng with the upper part of the thermostat,
and gently ghten the boom retaining screw.
The thermostats is now ready to operate.
INSTALLATION INSTRUCTION
Thank you for the purchase of our product. Please read the
instrucon before mounng and installing.
The device is an electronic thermostat for temperature control
by means of NTC sensors, located either internally within the
thermostat or externally by sensors.
PRODUCT PROGRAM
T60-E
Mul-funconal thermostat with built-in sensor and
ability of two external sensors, oor and/or air.
Without Wi-Fi funcon.
T60-EW
Mul-funconal thermostat with built-in sensor and
ability of two external sensors, oor and/or air.
With Wi-Fi funcon.
ES-T60 Accessory, external oor sensor probe, NTC 10 kΩ.
3 m connecon cable.
WARNING – Important Safety Instrucons
Disconnect the power supply before carrying out
any installaon or maintenance work,on this ther-
mostat and/or associated components.
The thermostat, and the associated components,
should only be installed by a qualied and autho-
rized electrician.
Electrical installaon must be in accordance with
appropriate naonal regulaons.
MOUNTING OF THE THERMOSTAT
The thermostat is designed to be ush mounted, and requires a
minimum 35 mm deep juncon box, recessed, within the wall.
PLACEMENT OF THE THERMOSTAT
The thermostat should be placed on the wall, approximately
1.5 m above the oor level, when the built-in sensor is used for
temperature regulaon. Ensure and allow free air circulaon
around it. Draught and direct sunlight, or other heat sources,
must be avoided. It can aect thermostat funcons.
When using a oor sensor, it is strongly recommended to follow
the underoor heang supplier’s advice and instrucons.
The sensor cable, of the accessory ES-T60, may be extended up
to 50 m by means of a separate two-core cable.

Energotech AB | Firmagatan 5 | SE-213 76 Malmö, Sweden | [phone] | inf[email protected] | www.energotech.com
TECHNICAL SPECIFICATION
19.03.27-01EN
Operang voltage / Power supply 85-230VAC, 50/60Hz
Standby power < 1.0W
Rated Current / Relay 16A resisve load, 230V
Seng range, temperature 5-45°C
Floor limitaon, temperature range 20-45°C
On/O dierenal ±0.5°C
Humidity sensor, air 0-100%
Operang modes
Three programming modes:
Weekday/Weekend (5 + 2)
- edit/set 4 me periods per day
Seven day programming (7)
- edit/set 4 me periods per day
24 hours mode
- edit/set 4 me periods
Hold/Timer mode:
- acvate and adjust a boost period of
up to 24h, by oponal seng range
temperature
Home/Away mode:
- the thermostat will turn on the heat-
ing, if the room temperature drops
below the set value.
Holiday mode:
- calendar based and programmable
in advance.
OFF mode:
- frost protecon included, by adjust-
able temperature range
Baery backup 2 months
Wireless standard, for T60-EW Wi-Fi 802.11 b/g/n (2.4G)
Appliance and protecon class Class II - IP20
Size, dimensions (H/W/D) 86/96/44 mm
Build-in depth 30 mm
Installaon type Flush, hole pitch 60 mm
Terminals 2.5 mm², screw cage clamp
Terminal wire size max. 2.5 mm²
Display size 3.5” - Color capacive touch
Display resoluon 480x320 TFT
Oponal external oor sensor NTC (10 kΩ), Class II, 3 meter
Oponal external room/air sensor NTC (10 kΩ), Class II, 3 meter
Max. length sensor cable 50 m, 2 x 1.5 mm²
CE marking
Low Voltage Direcve 2014/35/EU
EMC Direcve 2014/30/EU
RoHS Direcve 2011/65/EU
Wiring
Connect the wires in accordance with the diagram. The wires
must be connected as follows:
CONNECTIONS - WIRING
Terminal Marking
Terminal - (minus):
Terminal RT2:
Terminal RT1:
Terminal N:
Terminal N:
Terminal (empty):
Terminal L:
Terminal Load:
Sensor connecon point (cold)
External room/air sensor (hot)
External oor sensor (hot)
Output (neutral)
Power supply (neutral)
Do not connect
Power supply (live)
Output, max. 16A (3680W)
OPERATING THE THERMOSTAT
When powering up the thermostat, it will automacally start to
run in mode with the factory sengs. There is no mechanical
ON/OFF switch. To access this feature, simply so tap on the
touchscreen and/or the symbol
Programming and Setup
The thermostat carries a lot of features and sengs.
In order to access these points, download the user
manual at hp://www.energotech.com/products/
energocontrol/. It will guide you through the setup
of the dierent funcons and modes.
Output, max 16A
Main Supply
230V
Sensor Connecon Point
(cold wire)
External Sensor
(hot wire)
Floor Sensor
(hot wire)