Enersound T?500 User manual

1 of 5 14/11/10
T-500 USER MANUAL
1. INTRODUCTION
1.1 Front panel
1.2 LCD screen
Showing working channel (CH.01) or operating country mode
RF signal strength indicator.
Show Rx receiving signal --- N/A
Appears when keypad is locked
(10) DOWN AND KEY LOCK button
(11) Headphones output jack (φ3.5mm)
(12) Internal and external monitor switch
(13) Internal monitor indicator (red light)
(14) External monitor indicator (green light)
(15) LCD screen
(16) Input signal strength indicator: yellow light
(17) Input signal strength indicator: green light
(18) Input signal strength indicator: red light
(1) POWER button
(2) POWER indicator light (red light)
(3) MUTE button
(4) MUTE indicator light (red light)
(5) MIC input jack (φ3.5mm)
(6) Main Volume control
(7) Headphones output gain control
(8) UP button
(9) MENU button

2 of 5 14/11/10
Middle TX power --- N/A
High TX Power
Low TX Power
Appears when wide or narrow channel spacing
Appears when Test Tone function is on
Appears when the channel selected is in the scanning list --- N/A
N/A
N/A
Battery level, showing the battery capacity (voltage) --- N/A
1.3 Rear panel
Specifications:
Dimensions(W*H*D)：140mm*45 mm*116 mm；
Weight: 1450g；
2．FUNCTION DESCRIPTION
2.1 POWER ON/OFF
Pressing and holding [POWER] button for 2 seconds to turn on the radio, it will go to previous channel or
initial channel [CH 01] (see Fig 1), pressing it for 2 seconds again will turn off the radio.
Note: When the transmitter is turned on, the display will show full display during the start up.

3 of 5 14/11/10
2.2 CHANNEL SETTING
Fig 1
Press the [UP] or [Down] button to choose the operating channel from channel 1 to 17.
The TX power would be off during the switching interval.
2.3 Frequency SETTING
Fig 2
In “frequency display” mode, the transmitter will show the frequencies instead of channel numbers
(see Fig 2). Press [UP] or [Down] button to choose the operating frequency with default setting.
Please note that if going in steps of 0.1Mhz there are only 17 frequencies available because some
frequencies are restricted:
Allowed frequencies are: 72.1, 72.2, 72.3, 72.4, 72.5, 72.6, 72.7, 72.8, 72.9, 74.7, 75.3, 75.4, 75.5, 75.6,
75.7, 75.8, 75.9 Mhz.
2.4 Channel / Frequency Lock
Fig 3 Fig 4
By pressing and holding the UP or DOWN button for 5 seconds,the display will show “
“ icon (see Fig 3 & 4), the transmitter will be locked and the channel or frequency cannot be
changed until the unit is unlocked by pressing and holding the [UP] or [DOWN] button for 5
seconds again. The lock option will remain even if the unit is turned off and on again or is
unplugged from the power source.
3. Menu Options:
Pressed and held the [MENU] button for 5seconds, then the transmitter will enter into program
mode, there are five items Test Tone, Tx Power, Display, Modulation, Exit in setting menu.
After 10 seconds of inactivity the transmitter automatically will exit the program mode.
3.1 Test Tone
Enter into program mode first option will blink “TONE”.

4 of 5 14/11/10
Fig 5 Fig 6
•Press the [UP] or [DOWN] button to select the [TONE.OFF] or [TONE. ON](see Fig 5 & 6).
•Press [MENU] button to save the selected value and to go to the next menu option.
3.2 Tx Power
Enter into program mode second option will blink [POWER]
Fig 7 Fig 8
•Press the [UP] or [DOWN] button to select the [H] or [L] (see Fig 7 & 8).
•Press [MENU] button to save the selected value and to go to the next menu option.
3.3 Display Mode
Enter into program mode third option, the LCD will blink [DISPLAY].
Fig 9 Fig 10
•Press the [UP] or [DOWN] button can select [CHANNEL] or [FREQ] (see Fig 9 & 10).
•Press [MENU] button to save the selected value and to go to the next menu option.
3.4 F Deviation
Enter into program mode fourth option will blink “BAND-W”
Fig 11 Fig 12
•Press the[ UP] or [DOWN] button to select the Band [W] or [N] (see Fig 11 & 12).
•Press [MENU] button to save the setting and to go to the next menu option.
3.5 Exit
Fig 13
Enter into program mode fifth option will blink [EXIT]
•Press [MENU] button to exit the menu option.

5 of 5 14/11/10
4. RESET
Press and hold down [UP] + [DOWN] buttons, then Power On the transmitter, it will go back to the
initial channel [CH 01].
NOTE! This function is very useful if the transmitter is malfunctioning or if you want cancel all made
settings. Reset shall restore the transmitter to default settings.
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: This device may not cause harmful interference, and (2) this device must accept any interference
received, Including interference that may cause undesired operation.

ICWarning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement
This radio transmitter (identify the device by certification number, or model number if Category II) has
been approved by Industry Canada to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou
son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par
Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible
maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non
inclus dans cette liste,
ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
The device is compliance with RF field strength limits, users can obtain Canadian information on RF
exposure and compliance
Le présent appareil est conforme
Après examen de ce matériel aux conformité aux limites DAS et/ou aux limites d’intensité de champ RF,
les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité and compliance d’acquérir
les informations correspondantes