CYP CHDBT-1H2CE User manual

DRAFT
CHDBT-1H2CE
1 by 3 HDMI to HDMI & CAT5e/6/7 with LAN/IR/
RS-232 Transmitter
Operation Manual
Operation Manual

DRAFT

DRAFT
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2012 by Cypress Technology.
All Rights Reserved.
Version VR1.0 November 2012
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

DRAFT
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 29/10/12 Preliminary Release

DRAFT
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
7. Connection Diagram ............................ 5
8. Specications ........................................ 6
9. Acronyms ............................................... 7

DRAFT
1
1. INTRODUCTION
The HDMI over HDMI & CAT5e/6/7 transmitter can supports
resolutions up to 1080p Full HD, Deep Color and 4Kx2K timing, 3D and
multichannel digital audio formats such as LPCM 7.1CH, Dolby TrueHD,
Dolby Digital Plus and DTS-HD from Hi-Def sources to one HDTV and
CAT5e/6/7 outputs. This transmitter has the ability to provide you with 1
HDMI and 2 CAT5e/6/7 outputs where the HDMI can be connected to
HDMI display for instant display or cascading with another transmitter
and the CAT5e/6/7 can be connected to CAT5e/6/7 to HDMI
receivers for distance up to 100 meters.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1 x HDMI over HDMI & CAT5e/6/7 Transmitter
• 2 x IR Extender
• 2 x IR Emitter
• 2 x 3.5mm phone jack to D-Sub 9-pin adaptor cable
• 24V/2.7A DC Power Adaptor
• Power Cord
• Operation Manual
4. SYSTEM REQUIREMENTS
• Source equipment with HDMI output connector
• Display TV/monitor with HDMI input connector
• HDMI over CAT5e/6/7 receivers with industry CAT5e/6/7 cables

DRAFT
2
5. FEATURES
• HDMI v1.4 with 3D & 4Kx2K supported, HDCP and DVI compliant
• The HDMI and CAT5e/6/7 output are play the same source
simultaneously
• Supports Deep Color up to 1080p 36-bit
• Supports wide range of PC from VGA to WUXGA and HDTV
resolutions up to 4Kx2K
• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio transmission (32-192kHz Fs sample rate)
• Supports distances up to 100 meters through CAT5e/6/7 cables
• Supports PoE with capable receiver units

DRAFT
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
RS232 IN
A
RS232 IN
B
HDMI OUT HDMI IN
LINK POWER
SERVICE
DC 24V
1 2 3 4 5 6 7
1RS232 IN A/B
Connect to a PC/laptop or RS-232 enabled device (with supplied
3.5mm phone jack to D-Sub 9 pin adaptor) for the transmission of
RS-232 commands.
2HDMI OUT
Connect this port to display TVs/monitors.
3HDMI IN
Connect this port to source equipment such as DVD/Blu-ray player.
4LINK LED
This LED will illuminate when the receivers connected to source
with signal display on screen.
5SERVICE
This slot is reserved for factory service only.
6DC 24V & POWER LED
Plug the 24V DC power supply into the unit and connect
the adaptor to an AC outlet, the device will be power on
automatically once the power supply is connected the LED will
illuminate.

DRAFT
4
6.2 Rear Panel
IR A1
Extender
IR B1
Extendrt
IR A2
Blaster
IR B2
Blaster
LAN CAT5e/6 OU
TC
AT5e/6 OUT
MODE LINK
AB
MODE LINK
21 3 4 6 4 625 3 5
1LAN
Connect to an internet or network connection.
2IR A1/B1 IR Extender
Connect to the IR extender for IR signal reception of the remote
control of this deice or the source and display equipment. Ensure
that remote being used is within the direct line-of-sight of the IR
extender for it will send out the signal to designate receiver’s IR
output port.
3IR A2/B2 IR Blaster
Connect to the IR blasters for IR signal transmission. Place the IR
blaster in direct line-of-sight of the equipment to be controlled for
it will blaster out the IR signal received from the IR Digital Eye.
4MODE LED
When the device is power on the LED will ash.
5CAT5e/6 OUT A & B
Connect these ports to HDMI to CAT5e/6/7 receivers (with our
without PoE function) with CAT5e/6/7 cable to extend the signal
up to 100m.
6LINK LED
When the device is power on and this slot is connected from
receiver device with CAT5e/6/7 cable the LED will illuminate.

DRAFT
5
7. CONNECTION DIAGRAM
IR A1
Extender
IR B1
Extendrt
IR A2
Blaster
IR B2
Blaster
LAN CAT5e/6 OUTCAT5e/6 OUT
MODE LINK
AB
MODE LINK
RS232 IN
A
RS232 IN
B
HDMI OUTHDMI IN
LINK POWER
SERVICE
DC 24V
1.5m
60°
7m
3m 3m
60°
m
RX
CAT5e/6 In
Link
IR1 Extender
IR2 Blaster
Power
RS-232 Out
LAN
HDMI Out
CAT5e/6 to HDMI with LAN/IR/RS232
Receiver
1.5m
60°
7m
3m
3m
60°
m
RS-232 Equipped
PC or Notebook
RS-232 Equipped
PC or Notebook
SmartPhone
or Tablet
TV/Display
DVD/Blu-ray Player
Wireless Modem/Router
(Internet Connection)
TV/Display