Enertech Bentone B55 Series Technical specifications

Providing sustainable energy solutions worldwide
178 023 66-2 2016-11-24
Installation- and maintenance instruction
B 55 / B 65

6171 155 04 05-01
01. GENERAL
Description B55/B65
Components
1. Flame cone
2. Brake plate
3. Nozzle
4. Nozzle assembly
5. Ignition electrodes
11. Switch l-ll
12. Indicating lamp Stage 2
13. Cover, inspection glass
14. Indicating lamp Stage 1
15. Switch 0-l
17. Electric panel
20. Motor
 
22. Solenoid valves
23a. Connecting pipe
25a. Solenoid valve bloc Stage 2
26a. Nozzle assembly adjustment
 
27a. Scale, air regulation
27b. Scale, nozzle assembly
31a. Adjustment device, air
damper
32. Switch ll-lll
33. Indicating lamp Stage 3
34. Fuse
35. Damper motor
1(2)
31a 27a 26a 27b 25a 22 23a
21
123 4 5 17
13
34
33
32
12
11
14
15
20
35

7171 155 04 05-01
01. GENERAL
Description B55/B65
2(2)
Components
6. Ignition cables
7. Ignition transformer
8. Photocell
 
10. Front plate, relay base
16. Fan wheel
18. Contactor
19. Thermal overload protection
22. Solenoid valve
23a. Connecting pipe
23b. Hydraulic hose
24. Air intake
25a. Solenoid valve bloc Stage 2
25b. Solenoid valve bloc Stage 3
26a. Nozzle assembly adjustment
 
26b. Nozzle assembly adjustment
hydrauli
27a. Scale, air regulation
27b. Scale, Nozzle assembly
29. Air damper
30. Pump
31b. Adjustment device, Nozzle
assembly
35. Damper motor
16
19 18 9 10 7
8
6
292425a
23a22
30
26a
27a
35
31b 26b 22 27b
25b
23b
35
26b31b 22 27b
25a
23b
35

Försäkran om överensstämmelse
Declaration of conformity
Konformitätserklärung
Déclaration de conformité
Brännare, Burner, Ölbrenner, Brûleur
Certifikat TÜV Süddeutschland
Certifikat nr. Typ, Type:
08128915006 BF 1
0111110535004 B 1
0207110535005 B 2
02119815001 ST 97, ST 108, ST 120,
ST 133, ST 146
02119815002 B 9, B 10, B 11
Certifikat nr. Typ, Type:
02119815003 B 20, B 30, B 40, B 45
02119815004 B 50, B 60, B 70, B 80
040588622001 B 55
040588622002 B 65
13129815007 B 45 MF, B 45-2 MF
Enertech AB försäkrar under eget ansvar att ovannämnda produkter är i överensstämmelse med följande standarder eller andra
regelgivande dokument och uppfyller tillämpliga delar i EU direktiv.
Enertech AB declares under sole responsibility that the above mentioned product is in conformity with the following standards or other
normative documents and follows the provisions of applicable parts in the following EU Directives.
Enertech AB erklärt in eigener Verantwortung, dass obenstehende Produkte mit folgenden Normen oder anderen normativen
Dokumenten und anwendbare Teile in EU-Direktiven in Übereinstimmung stehen
Enertech AB déclare sous sa seule responsabilité que les produits désignés ci-dessus sont conformes aux normes et aux documents
normatifs suivants et satisfont aux critères applicables des directives CE suivantes:
Dokument: EN 267
EN 60335
EU direktiv. EU Directives, EU-Direktiven, CE suivantes:
2004/108/EC Elektromagnetisk kompatibilitet, Electromagnetic compatibility EC-Richtlinie, Compatibilité électromagnétique
2006/95/EC Lågspänningsdirektivet, Low-voltage directive, Niederspannungs-Richtlinie, Directive sur les basses tensions
2006/42/EC Maskindirektivet, Machinery directive, Maschinen-Richtlinie, Directive sur les machines
92/42/EEC Verkningsgradsdirektivet, Efficiency directive, Wirkungsgrad-Richtlinie, Directive sur les exigences de rendement
Genom att brännaren uppfyller ovannämnda standarder och direktiv erhåller brännaren CE - märkningen.
In that the burner conforms to the above mentioned standards it is awarded the CE mark.
Indem der Brenner die obengenannten Normen und Richtlinien erfüllt, erhält der Brenner die CE-Kennzeichnung.
Du fait de leur conformité aux directives mentionnées ci-dessus, les brûleurs Bentone bénéficient du marquage CE.
Enertech AB, Bentone Division/
är kvalitetscertifierat enligt/
is quality certified according to/
ist nach dem Qualitätsmanagement /
est certifiée à la norme de qualité
SS-EN ISO 9001:2008
Ljungby, Sweden, 150227 (27/02/15)
ENERTECH AB Bentone Division
Box 309
SE-341 26 Ljungby Sweden
Håkan Lennartsson
171 901 06 15-01

9
01. GENERAL
Manual
- The contents of this manual are to be observed by all who work for any
reason on the unit and its appertaining system parts.
- This manual is intended especially for authorised personnel.
- This manual is to be regarded as part of the burner and shall always
be available near the place of installation.
Safety directions
The electrical installation shall be made according to valid regulations for

personal injury is avoided.
Care should be taken by the installer to ensure that no electrical cables or
fuel/gas pipes are trapped or damaged during installation or service/maintenance.
Condensation in chimney A modern burner works with less air surplus and often with a smaller nozzle

of condensation in the chimney. The risk is greater if the cross sectional

higher than 60°C measured 0.5 m from the top of the chimney.
Setting the burner            

or condensation in the chimney.
171 355 10 07-01

10 171 535 13 06-01
02. TECHNICAL DATA
Type designation B55-2H/B55-2/B55-2R/B55-3R/B65-2H/B65-2/B65-2R/B65-3R
Dimensions
Length of
burner tube
B55
Flange
MeasureB
B55
Burner tube
Measure C
B55
Burner tube
Measure D
B55
Length of
burner tube
B65
Flange
MeasureB
B65
Burner tube
Measure C
B65
Burner tube
Measure D
B65
Standard 1 303 273 160 155 288 258 200 155
Standard 2 403 373 160 155 388 358 200 155
Standard 3 503 473 160 155 488 458 200 155
Output range and nozzles recommended

Recommended nozzle and pressure
Because of the different boiler types, combustion chamber geometries

spray angle or spray pattern.It should be noted that the spray angle and spray
pattern will vary depending on the pump pressure.
Nozzle 45°S Danfoss
45°B Danfoss
60°S Danfoss
60°B Danfoss
Pump pressure 14 bar (12 - 16 bar)
On burners equipped with hydraulic air control or optimization the oil pressure
should not be less than 14 bar.
Oil capacity Output Recommended nozzle Recommended
Pump pressure
kg/h  Mcal/h Angle Danfoss
B55-2H, B55-2, B55-2R 14-67 166-795 143-685 45°-60° S, B 14 bar
B55-3R 14-64 166-759 143-654 45°-60° S, B 14 bar
B65-2H, B65-2, B65-2R 24-99 285-1174 246-1012 45°-60° S, B 14 bar
B65-3R 24-99 285-1174 246-1012 45°-60° S, B 14 bar
1(3)
B


C
405
400
321
610
595
290
D



 







11 171 535 13 06-01
02. TECHNICAL DATA

2(3)
B55-2
14-67 kg/h
 
B55-2R
B55-2H/B55-2
Measured (test)
B65
24-99 kg/h

B65
Measured (test)
B55-3R
14-64 kg/h
 
B55-3R
Measured (test)
Unbroken line is the approved wor-


100 200 300 400 500 600 700 800
-2
0
2
4
6
8
10

200 300 400 600 700 800 900 1000
-2
6
8
12
14


2
0
4
10
500 1100 1200


100 200 300 400 500 600 700 800
-2
0
2
4
6
8
10

12 171 535 13 06-01
The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.
02. TECHNICAL DATA
Nozzle table
3(3)
Gph 10 11 12 13
           
2,75 10,24 121 104 10,73 127 109 11,21 133 114 11,67 138 119
3,00 11,16 132 114 11,71 139 119 12,23 145 125 12,73 151 130
3,50 13,03 154 133 13,66 162 139 14,27 169 146 14,85 176 151
4,00 14,89 176 152 15,62 185 159 16,31 193 166 16,97 201 173
4,50 16,75 199 171 17,57 208 179 18,35 218 187 19,10 226 195
5,00 18,62 220 190 19,52 231 199 20,39 242 208 21,22 252 216
5,50 20,48 243 209 21,47 255 219 22,43 266 229 23,34 277 238
6,00 22,34 265 228 23,42 278 239 24,47 290 250 25,46 302 260
6,50 24,20 287 247 25,37 301 259 26,51 314 270 27,58 327 281
7,00 26,06 309 266 27,33 324 279 28,55 339 291 29,70 352 303
7,50 27,92 331 285 29,28 347 299 30,59 363 312 31,83 377 325
8,00 29,79 353 304 31,23 370 318 32,63 387 333 33,95 403 346
8,50 31,65 375 323 33,18 393 338 34,66 411 353 36,07 428 368
9,00 33,59 398 343 35,14 417 358 63,71 435 374 38,19 453 389
9,50 35,37 419 361 37,09 440 378 38,74 549 395 40,31 478 411
10,00 37,23 441 380 39,04 463 398 40,78 484 416 42,44 503 433
11,00 40,96 486 418 42,94 509 438 44,86 532 457 46,68 554 476
12,00 44,68 530 456 46,85 556 478 48,94 580 499 50,92 604 519
14,00 52,12 618 531 54,65 648 557 57,10 677 582 59,41 705 606
16,00 59,57 706 607 62,46 741 637 65,26 774 666 67,90 805 692
18,00 67,02 795 683 70,27 833 717 73,41 871 749 76,39 906 779
20,00 74,47 883 759 78,08 926 796 81,57 967 832 84,87 1007 865
Pump pressure bar
Gph 14 15 16 17
           
2,75 12,11 144 123 12,53 149 128 12,95 154 132 13,35 158 136
3,00 13,21 157 135 13,67 162 139 14,13 168 144 14,56 173 148
3,50 15,42 183 157 15,95 189 163 16,49 196 168 16,99 201 173
4,00 17,62 209 180 18,23 216 186 18,84 223 192 19,42 230 198
4,50 19,82 235 202 20,51 243 209 21,20 251 216 21,84 259 223
5,00 22,03 261 225 22,79 270 232 23,55 279 240 24,27 288 247
5,50 24,23 287 247 25,07 297 256 25,91 307 264 26,70 317 272
6,00 26,43 313 270 27,49 326 280 28,27 335 288 29,13 345 297
6,50 28,63 340 292 29,63 351 302 30,62 363 312 31,55 374 322
7,00 30,84 366 314 31,91 378 325 32,98 391 336 33,98 403 347
7,50 33,04 392 337 34,19 405 349 35,33 419 360 36,41 432 371
8,00 35,25 418 359 36,47 433 372 37,69 447 384 38,80 460 396
8,50 37,45 444 382 38,74 459 395 40,04 475 408 41,26 489 421
9,00 39,65 470 404 41,02 486 418 42,40 503 432 43,69 518 446
9,50 41,85 496 427 43,30 514 442 44,75 531 456 46,11 547 470
10,00 44,06 523 449 45,58 541 465 47,11 559 480 47,11 559 480
11,00 48,46 575 494 50,14 595 511 51,82 615 528 53,40 633 545
12,00 52,87 627 539 54,70 648 558 56,53 670 576 58,25 691 594
14,00 62,68 732 629 63,81 757 651 65,95 778 669 67,96 806 693
16,00 70,49 836 719 72,93 865 744 75,38 894 769 77,67 921 792
18,00 79,30 940 809 82,05 973 837 84,80 1006 865 87,38 1036 891
20,00 88,11 1045 899 91,17 1081 930 94,22 1117 961 97,09 1151 990
Pump pressure bar

13 171 635 02 04-01
03. INSTALLATION
Acceptance inspection
Ensure that everything is delivered and that there is no transport damage.
If there is anything wrong with the delivery, please report it to the supplier.
Any transport damage should be reported to the forwarding company.
Preparations for installation
Ensure that the size and capacity range of the burner are suitable for the
            
power of the burner.
Distribution of oil
To ensure satisfactory operation it is essential that the oil distribution sys-
tem is correct.
Observe the following:
- See Pump instructions for choice of tube diameter, tube length and height
difference.
 
   
sharp bending when swinging out the burner or removing it for service.
 
Electrical connections
The main power switch must be turned off before beginning electrical in-
stallation. If the boiler has a 7-pin and a 4-pin Eurostecker connector these
will often connect straight to the burner. If not, use the connectors supplied.
A 5-pin connector supplies the burner motor with a separate 3-phase supply.
See connection under the Electrical equipment heading.
If another electrical connection is used than the one recommended by Bentone,
there might be a risk of material damage or personal injury.
Choice of nozzle
See under Technical Data: Recommended nozzle and table of nozzles.

Basic burner settings can be made before commissioning as shown in the
diagram. See Basic settings. Note that these are just basic settings and
must be correctly adjusted when the burner has been started. Flue gas analysis
and soot measurement should be carried out at this time.
!
Warning

14
03. INSTALLATION
Burner installation
Hole pattern
Check that the hole pattern on the boiler matches the pattern on the burner

Flame head d1d2d3
B55 (160)* 165 M12 (226)* 254-295
B65 (160)* 210 M12 (226)* 254-295
 

Installing the burner
 
 
3. Insulate between the burner pipe and boiler door to reduce heat radiation.
4. Slide the burner body on to the guides.
5. Pull the brake plate off the oil pipe.
6. Fit the chosen nozzles (see Technical data).
7. Fit the brake plate and check the ignition electrodes
(see Servicing the burner).
8. Slide the burner together and secure it with the nuts (E).
Oil lines
1. Check the size of the oil line (see Pump instructions).
 

 
(see Pump instructions).
 
to the right couplings on the oil pump. The hoses must be positioned so
that they are not subjected to tensile stress or sharp bending.
5. Bleed the oil system. The oil pump will be damaged if it is run dry.
            
commissioning.
Electrical connections
1. Turn off the main power switch.
2. Connect the Eurostecker connectors (see Electrical equipment).
3. Check that the burner control switch (S1) is off.
4. Fit the Eurostecker connectors on the burner.
5. Turn on the main power switch.
6. Check the direction of rotation of the burner motor.
171 635 03 04-01
 
Return line Suction line

E
d2
d3
d3

15
Choice of nozzle  
B65-2H/B65-2/B65-2R  
 
According to the table of nozzles this gives the following nozzles:
Stage 1 : 8,50 Gph
Stage 2 : 6,00 Gph
Pump pressure : 14 bar
Basic settings Nozzle assembly Stage 2 = 15
B65-2H Air adjustment Stage 1 = 25°
Stage 2 = 65°
Each graduation on the scale corresponds to 10°.
Basic settings 
B65-2 Nozzle assembly Stage 2 = 15
Damper motor Closed = 0° Blue cam
Stage 1 = 25° Orange cam
  
Stage 2 = 65° Red cam
              
  
characteristics when switching between stages, but for a basic setting the
black cam should be placed in the middle.
Basic settings 
B65-2R Nozzle assembly Stage 1 = 0
Stage 2 = 15
Damper motor Closed = 0° Blue cam
Stage 1 = 25° Orange cam
  
Stage 2 = 65° Red cam
              
  
characteristics when switching between stages, but for a basic setting the
black cam should be placed in the middle.
Choice of nozzle 
B65-3R 
According to the table of nozzles this gives the following nozzles:
Stage 1 : 5,50 Gph
Stage 2 : 5,50 Gph
Stage 3 : 5,50 Gph
Pump pressure : 14 bar
Basic settings 
B65-3R
Nozzle assembly Stage 1/2= 5
Stage 3 = 20
Damper motor Stage 1 = 10° Blue cam
  
Stage 2 = 44° Orange cam
  
Stage 3 = 80° Red cam

the cams for Stage 1 and Stage 2, and between Stage 2 and Stage 3,

characteristics when switching between stages, but for a basic setting the

04. BASIC SETTINGS
Typical basic settings for B65-2H/B65-2/B65-2R/B65-3R
171 725 10 04-01

16
04. BASIC SETTINGS
Set values for nozzle assembly B55
Set values for nozzle assembly B65
Set values for air damper B55
Set values for air damper B65
171 725 11 04-01
100 700600500400300 200 800

0
20
40
80
100
120
60
Air, <°
0
20
60
40
80
100
120
600400200 800 1000 1200

Air, <°
600400200 800
0
10
30
20
40
1000 1200

Scale, nozzle as-
sembly

40
100
0
10
20
30
700600500400
300
200 800
Scale, nozzle
assembly

17

Nozzle assembly regulation is used to achieve the most favourable pressure
drop possible across the brake plate.
Nozzle assembly regulation should be adjusted for Stage 2 output.
Adjustment
Adjust to the desired position on the scale (A) using the set screw (B) (turning
anti-clockwise reduces the pressure drop and moves the brake plate outwards).
If pulsation occurs, the pressure drop across the brake plate can be alte-
red until pulsation stops.
Nozzle assembly regulation – adjustable brake plate
Nozzle assembly regulation is used to achieve the most favourable pressure
drop possible across the brake plate for each output stage.

Nozzle assembly regulation adjusts the position of the brake plate between
Stage 1 and Stage 2 by means of a hydraulic piston.
Three nozzles
Nozzle assembly regulation adjusts the position of the brake plate between
Stage 2 and Stage 3 by means of a hydraulic piston.

Undo the locking nut.
Adjust to the desired position on the scale (A) by sliding the plate to the desired
position. Tighten the locking nut (C).
High load
Adjust to the desired position on the scale (A) using the set screw (D) (turning
anti-clockwise reduces the pressure drop and moves the brake plate outwards).
If pulsation occurs, the pressure drop across the brake plate can be alte-
red until pulsation stops.
Hydraulic air adjustment
Stage 1
Set the control switch (S2) to low load (I). Undo the screw (E), turn the damper
to the desired position and retighten the screw (E).
Stage 2
Set the control switch (S2) to high load (I). Use the adjuster pin to screw the
sleeve (F) in (to reduce) or out (to increase). The position of the damper can

air settings.
04. BASIC SETTINGS
171 725 12 04-01
EF G
C AD
BA

18
04. BASIC SETTINGS
Damper motor 2-Stage
The damper motor rotates the damper between three preset positions.
These positions are controlled at the motor by micro-switches, the switching
positions of which are set using the coloured cams. There is also a black cam,
which controls the activation of solenoid valve 2.

Remove the cover from the damper motor and change the positions of the
cams by turning them with the aid of the tool supplied. To deactivate a cam
while you are turning it we recommend that you switch to a different stage
and then switch back after adjustment is complete in order to check the result.
Stage 1 Adjust the operating switch to Stage 2 (II).
* Reduce the air volume:
Turn orange cam towards 0°.
* Increase the air volume:
Turn orange cam towards 90°.
Adjust the operating switch back to low capacity and check.
Stage 2 Adjust the operating switch to Stage 1 (I).
* Reduce the air volume:
Turn red cam towards 0°.
* Increase the air volume:
Turn red cam towards 90°.
If the red cam is moved, change the black cam as much. Adjust the operating
switch back to Stage 2 and ensure that the correct air volume has been obtained.
Closed The blue cam is the limit position for fully closed damper and it is normally
not necessary to change it.
Releasing The damper motor can be released using the white release button. This feature

To release. Press down the shaft and slide it outwards until it disengages
from the milled slot.
To engage. Slide the shaft inwards and release. Adjust the position of the
motor so that the cogs mesh with each other.
171 725 13 04-01
Releasing button
N.B. The upper position
is the standard position
Stage 2 (red)
Stage 1 (orange)
Closed damper (blue)
Solenoid valve Stage 2
(black)

19
04. BASIC SETTINGS
Damper motor 3-Stage
The damper motor rotates the damper between three preset positions.
These positions are controlled at the motor by micro-switches, the switching
positions of which are set using the coloured cams. There is also a black
cam, which controls the activation of solenoid valve 2 and a green one which
controls the activation of solenoid valve 3.

Remove the cover from the damper motor and change the positions of the
cams by turning them with the aid of the tool supplied. To deactivate a cam
while you are turning it we recommend that you switch to a different stage
and then switch back after adjustment is complete in order to check the result.
Stage 1 Adjust the operating switch to Stage 2 (II).
* Reduce the air volume:
Turn blue cam towards 0°.
* Increase the air volume:
Turn blue cam towards 90°.
Adjust the operating switch back to Stage 1 and check.
Stage 2 Adjust the operating switch to Stage 1 (I).
* Reduce the air volume:
Turn orange cam towards 0°.
* Increase the air volume:
Turn orange cam towards 90°.
If the orange cam is moved, change the black cam as much. Adjust the
operating switch back to Stage 2 and ensure that the correct air volume has
been obtained.
Stage 3 Adjust the operating switch to Stage 2 (II).
* Reduce the air volume:
Turn red cam towards 0°.
* Increase the air volume:
Turn red cam towards 90°.
If the red cam is moved, change the green cam as much. Adjust the operating
switch to Stage 3 (III) and ensure that the correct air volume has been
obtained.
Releasing The damper motor can be released using the white release button. This feature

To release. Press down the shaft and slide it outwards until it disengages
from the milled slot.
To engage. Slide the shaft inwards and release. Adjust the position of the
motor so that the cogs mesh with each other.
171 725 14 04-01
Releasing button
N.B. The upper
position is the
standard position
Solenoid valve Stage 3 (green)
Solenoid valve Stage 2 (black)
Stage 3 (red)
Stage 2 (orange)
Stage 1 (blue)

20
05. MAINTENANCE
Servicing the burner device
 1. Turn off the main power switch and disconnect the Eurostecker connectors
from the burner.
2. Undo the nuts (E) and pull out the burner body on its guides.
3. Undo and remove the brake plate from the oil pipe.
4. Unscrew the nozzles.
5. Fit the nozzles.
6. Fit the brake plate (see Adjusting the brake plate).
7. Check the ignition electrodes (see Adjusting ignition electrodes).
Replace if necessary.
8. Slide the burner together and secure it with the nuts (E).
9. Connect the Eurostecker connectors and turn on the main power switch.
10. Check combustion*.
Note:
        
analysis and soot measurement must be carried out on the installation.
NOTE!
If nozzles are dirty always replace them with new ones. Do not clean them.
On boilers with a hinged door, the door can be opened and the burner pipe


lifted off the guides, or the oil pipe must be disconnected from the solenoid
valves to be removed for servicing.
Adjusting the ignition electrodes and brake plate
Adjustment dimensions for ignition electrodes.
Burner, type a b c d e
B55-2 2,5-3,0 2,0 6,5-7,0 2,0 6,0-7,0
B55-3 2,5-3,0 0,0 6,5-7,0 2,0 6,0-7,0
B65-2 2,5-3,0 2,0 6,5-7,0 2,0 10,0-12,0
B65-3 2,5-3,0 0,0 6,5-7,0 2,0 10,0-12,0
NOTE!
It is important that the spark does not strike the brake plate or nozzle.
171 755 12 04-01
B55 B65





E
b

a
 c
d


a
b

c
d
 

e
e

21
05. MAINTENANCE
Servicing the air damper
 1. Turn off the main power switch and disconnect the Eurostecker connectors
from the burner.
2. Undo the nuts (E) and pull out the burner body on its guides.
3. Remove the intake grille from the air intake.
4. Release the damper motor.
5. Clean the air damper (F) and the intake. Lubricate the damper shaft if
applicable.
6. Re-engage the damper motor.
7. Fit the intake grille over the air intake.
8. Slide the burner together and secure it with the nuts (E).
9. Connect the Eurostecker connectors and turn on the main power switch.
10. Check combustion*.
Replacing the damper motor
 1. Turn off the main power switch and disconnect the Eurostecker connectors
from the burner.
2. Note the positions of the cables and then disconnect the cables from the
damper motor
3. Release the damper motor and lock it at 30°.
4. Undo the screws (G) that secure the mounting plate for the damper motor.
5. Raise it carefully so that the air damper stays in the air intake.
6. Disconnect the (H) link arm from the motor shaft.
7. Separate the damper motor from the mounting plate (I).
 
9. Connect the link arm to the damper motor shaft. It is important that the
screw is at right angles to the plane of the shaft.
10. Release the damper motor and lock it at 30°.
11. Fit the mounting plate by guiding the link arm into the attachment point on
the air damper and the air damper shaft into the mounting plate (make

shaft).
12. Release the damper motor and check that the damper moves freely.
Close the damper and zero the graduated scale on the damper motor.
13. Make the electrical connections to the damper motor.
14. Reset the damper motor cams.
15. Connect the Eurostecker connectors and turn on the main power switch.
16. Check combustion.*
Replacing the oil pump B55/B65
 1. Turn off the main power switch and disconnect the Eurostecker connectors
from the burner.
2. Disconnect the oil hoses from the pump.
3. Undo the screws (J) and pull out the oil pump.
4. Measure the distance between the pump mounting and the pump coupling (K).
5. Transfer the pump coupling to the new pump and adjust to give the
same spacing between the pump and pump coupling as before (K)
6. Fit the oil pump on the burner and tighten the screws (J). (It is important
that splines on the pump shaft align correctly with the pump coupling.)
7. Fit the oil hoses.
8. Connect the Eurostecker connectors and turn on the main power switch.
9. Bleed the pump, start the burner and adjust to the correct oil pressure.
10. Check combustion.*
Note:
 
analysis and soot measurement must be carried out on the installation.
171 755 13 05-01
E
F

JK



GI
H

22
06. INSTRUCTIONS PUMP TYPE RSA 95 & 125
Technical data
RSA 95 RSA 125
 2/s
Pressure range at viscosity 1,3-1,8: 5,5-12,0 bar
Pressure range at viscosity 1,8-18,0: 2,5-21,0 bar
Oil temperature: -10 to+70°C
Nozzle capacity at viscosity 4,3: 150-190 l/h 215-260 l/h
Gearwheel capacity: 225 l/h 294 l/h
 
Components






7. By-pass plug
8. Pressure adjustment, 4 mm Allen key
Mounting/dismounting by-pass plug

system the by-pass plug must be removed so that there is a free passage
back to the suction side through the return line with the return port closed.
(s.7).
Purging
On 1-pipe systems it is necessary to purge the pump. On 2-pipe systems
purging is automatic through the return line.


- Close the oil valves.
 
 
- Replace the cover gasket.
 
- Open the oil valves.
171 805 08 04-01

5





8
1
7
2
3
4
6


23
06. INSTRUCTIONS PUMP TYPE RSA 95 & 125
Function Danfoss RSA 95 - 125
             

wheel set pumps the oil to the pressure side and at the same time the oil
         
which opens when the set pressure is reached.









the oil pressure. The spring in the regulating valve presses the regulating

and ensures that the nozzle line is effectively shut off.
If the pump is overloaded, i.e. more oil is demanded than the gearwheel is
able to pump under the given conditions, the oil pressure falls below the set
value because the piston of the regulating valve moves towards its closed

This can be remedied by
- reducing the pump pressure
- reducing the capacity, i.e. smaller nozzle or greater resistance
- changing to a pump with higher capacity
1. Nozzle Stage 1
2. Nozzle Stage 2
3. Nozzle Stage 3
4. Solenoid valve Stage 1 (Y1)
5. Solenoid valve Stage 2 (Y2)
6. Solenoid valve Stage 3 (Y3)
7. Safety valve for nozzle (Y1S)
Only for capacities over 100 kg/h or on special request by customer.
8. Hydraulic control device
Only on burners with hydraulic air control or nozzle assembly optimisation.
9. Oil pump

solenoid valve nozzle 2 (Y2).
Schematic diagram
171 805 09 04-01