Enertech Bentone B 45 A2.2 Technical specifications

Providing sustainable energy solutions worldwide
178 005 56
Installation- and maintenance instruction
B 45 A2.2

DESCRIPTION
1. Flame cone
2. Fan housing
3. Fan wheel
4. Damper motor
5. Motor
6. Pump
7. Shrouded disc
8. Nozzle
9. Ignition transformer
10. Nozzle assembly
11. Air intake
12. Air damper
13. Connecting pipe Stage 1
14. Connecting pipe Stage 2
15. Solenoid valves
16. Nozzle assembly adjustment
17. Connecting pipe, pump-
adjustment device
18. Adjustment device, Nozzle
assembly adjustment
19. Fuse
20. Indicating lamp Stage 2
21. Switch I-II
22. Indicating lamp Stage 1
23. Switch 0-I
24. Contactor
25. Control box
26. Drive coupling
27. Conical shield plate
28. Ignition electrodes
171 205 44 12-01
Components
THE BURNERS MUST NOT BE FIRED WITHOUT FITTING NOZZLES SUPPLIED
Warning
!

Dimensions
171 235 05 09-01
TECHNICAL DATA
Electrode adjustment
Because of different boiler types
existing on the market, with varying
combustion chamber designs, it is
not possible to state a denite spray
angle or spray pattern.
Recommended nozzle
Note that the spray angle and the
spray pattern change with the pump
pressure.
Output range and nozzles recommended
The net caloric value of 11,86 kWh/kg for light oil has been used.
Length of burner tube Flange
Measure B
B45A2 270 238
B45A2 370 338
Oil capacity Capacity Recommended nozzle Recommended
Pump pressure
kg/h kW Mcal/h Angle Danfoss Monarch Bar
B45A2 8,5-45,5 101-540 87-464 45° - 60° S, B R, PLP 14 bar
Type designation B45A2
262
515 B480
ø162
ø134
252
335
328
3,5-4,0
5,0-6,0
7,0-9,0
2,0-3,0

TECHNICAL DATA
171 225 34 09-01
Dimensions of ange
14
ø134
(ø200) ø224-260

171 305 31 09-01
General rules
The installation of an oil burner should
be carried out in accordance with local
regulations. The installer of the burner
must therefore be aware of all regu-
lations relating to oil and combustion.
Only oil suitable for the burner should
be used and then in combination with
a suitable oil lter before the oil pump
of the burner.
If the burner is replacing an existing
burner make sure that the oil lter is
replaced or cleaned. The installation
must only be undertaken by expe-
rienced personnel. Care should be
taken by the installer to ensure that no
electrical cables or fuel/gas pipes are
trapped or damaged during installation
or service/maintenance.
Installation instructions
General installation instructions ac-
company the burner and should be
left in a prominent place adjacent to
the burner.
Adjustment of burner
The burner is from the factory pre-set
to an average value that must then
be adjusted to the boiler in question.
All burner adjustments must be made
in accordance with boiler manufactu-
rers instructions.These must include
the checking of ue gas temperatures,
average water temperature and CO2
or O2concentration.
To adjust the combustion device, start
by increasing the air volume and the
nozzle assembly somewhat. When
the burner starts it is burning with
excess air and smoke number 0. Re-
duce the nozzle assembly adjustment
until soot occurs, and then increase
the adjustment to make the soot
disappear again. Then the volume of
air is reduced until soot occurs and
increased again to reach a combus-
tion free of soot.
By this procedure an optimum adjust-
ment is obtained. If larger nozzles are
used the preadjustment of both the
air volume and the nozzle assembly
must be increased.
A whistling sound may be heard
which can be eliminated or reduced
as follows: Increase the nozzle as-
sembly adjustment somewhat. The
CO2-content and consequently the air
volume will then be reduced.
Maintenance
The boiler/burner should be examined
regularly for any signs of malfunction
or oil leakage.
Oil supply
The oil line should be dimensio-
ned in accordance with the pump
manufacturer´s instruction. In the suc-
tion line to the burner a lter should
be mounted to prevent any particles
in the oil from reaching the burner.
If the installation consists of several
burners each one should have its own
suction line from the tank or a circula-
tion system should be used.
The temperature in the oil line should
be kept as constant as possible.Avoid
exposing the line to excessive cold
which may cause blockages of paraf-
n deposits.
The oil pipe and electric cable should
be tted so that the burner can be
placed on the oor for inspection of
the combustion device.
Condensation in chimney
A modern burner works with less
excess air and often also with smal-
ler nozzles than older models. This
increases the efciency but also the
risk of condensation in the chimney.
The risk increases if the area of the
chimney ue is too large. The tempe-
rature of the ue gases should exceed
60°C measured 0,5 metres from the
chimney top.
Measures to raise the temperature:
Insulate the chimney in cold attics
Install a tube in the chimney
Install a draught regulator (dilutes the
ue gases during operation and dries
them up during standstill)
Increase the oil quantity
Raise the ue gas temperature by re-
moving turbulators, if any, in the boiler.
Pump adjustment
See separate description.
GENERAL INSTRUCTIONS
Air adjustment
See page "Air adjustment with damper
motor".
Adjustment of nozzle assembly

Releasing button
N.B. The upper position is the standard
position
High capacity (red)
Low capacity (orange)
Closed damper (blue))
Solenoid valve High capacity (black)
171 315 07 09-01
AIR ADJUSTMENT WITH DAMPER MOTOR
The damper motor turns the damper
between 3 preset positions: fully
closed, low capacity and high capa-
city. These positions are controlled in
the motor by cams which are set by
means of the coloured disks. In ad-
dition there is a black disk controlling
the connection of solenoid valve 2.
If the air volume needs changing:
Remove the cover from the damper
motor and change the position of the
cams by turning them by hand. See g.
Low capacity:
Adjust the operating switch to high
capacity (II).
• Reduce the air volume:
Turn orange cam towards 0°.
• Increase the air volume:
Turn orange cam towards 90°.
Adjust the operating switch back to
low capacity and check.
Full capacity:
Adjust the operating switch to low
capacity (I).
• Reduce the air volume:
Turn red cam towards 0°.
• Increase the air volume:
Turn red cam towards 90°.
If the red cam is moved, change the
black cam as much. Adjust the opera-
ting switch back to high capacity and
ensure that the correct air volume has
been obtained.
Note!
The blue cam is the limit position for
fully closed damper and it is normally
not necessary to change it.
Releasing button
By pressing the button and snapping
it down, the motor will be released
and the damper can easily be turned.
This function facilitates an exchange
of damper motor.

171 305 34 09-01
MAINTENANCE OF OIL BURNER
Warning: Before doing any service switch off power at the main switch and cut off the oil supply.
Service of burner head
(alt. A)
Service of burner head
(alt. B)
Note!
For maintenance of the brake plate,
nozzles, electrodes etc, when using
a long design of the burner tube, you
have to remove the nozzle assembly
from the connecting pipe and move
the assembly backwards in the fan
housing (from the boiler).

Oil burner control: LMO24.255
Wiring diagram
ELECTRIC EQUIPMENT
171 435 27 15-01
1(3)
If the boiler is not equipped with wired contacts,connect the enclosed contacts to terminals X4 and X6 in accordance with wiring diagram.
1N ~ 50/60 Hz 230 V

ELECTRIC EQUIPMENT
Oil burner control: LMO24.255 List of components
A1 Oil burner control
B1 Photoresistor
F1 Fuse
H1 Lamp, low capacity
H2 Lamp, high capacity
H3 Lamp, lock-out signal 230 V
K1 Thermal overload protection
M1 Burner motor
M2 Damper motor SQN75.244A21B
P1 Time meter, low capacity
(optional)
P2 Time meter, high capacity
(optional)
S1 Operating switch
S2 Operating switch, high/low
capacity
S3 Control thermostat
S4 Temperature limiter
S5 Micro switch for hinged door
S6 Control thermostat, high/low
S7 Main switch
T1 Ignition transformer
X1 Connection terminal board
X2 Earth terminal
X3 Plug-in contact, burner
X4 Plug-in contact, boiler
X5 Plug-in contact
high/low capacity burner
X6 Plug-in contact
high/low capacity boiler
Y1 Solenoid valve 1
Y2 Solenoid valve 2
If S6 is missing connection between T6 and T8.
Mains connection and fuse in accordance with local regulations.
Function
1. Switch on operating switch and twin thermostat
A spark is formed. The air damper motor opens the damper to low load
position. The burner motor starts, the prepurge goes on till the prepurge
period expires and the solenoid valve 1 opens (2).
2. Solenoid valve 1 opens
Oil mist is formed and ignited. The photocell indicates a ame.
3. The safety time expires
a. If no ame is established before this time limit the control cuts out.
b. If for some reasons the ame disappears after this time limit, the burner
will make an attempt to re-start.
4. High/Low thermostat ON
The burner is in operating position and can now change between full load
and low load.
4-5. Operating position
If the burner operation is interrupted by means of the main switch or the
thermostat, a new start takes place when the conditions in accordance
with point 1 are fullled.
The oil burner control cuts out
A red lamp in the control is lit. Press the reset button and the burner
re-starts.
Technical data
Pre-ignition time: 25 s
Pre-purge time: 26 s
Post-ignition time: 5 s
Safety lock-out time: < 5 s
Reset time after lockout: < 1 s
Reaction time on ame failure: < 1 s
Ambient temperature: from - 20 to +60°C
Min. current with ame established: 45µ A
Max. photo current at start: 5,5µ A
Enclosure: IP 40
Control of photo current
Current through photo unit is measured with a d.c. ammeter (a moving coil
instrument connected in series with the photo unit).
171 435 27 15-01
2(3)
Max loading K1
Connection A1,A2 / 95, 96 / 97, 98
Max 0,2A/15W

171 435 27 15-01
Colour codes LMO14/24
When the burner starts, three signal lights in the reset switch indicate
the normal sequence, as well as provide indication if something ab-
normal is happening in accordance with the following table:
Preheater in operation Solid yellow
Ignition switched on Flashing yellow
Normal operation Solid green
Operation, poor ame signal Flashing green
Undervoltage Flashing yellow-red
Fault, alarm Solid red
False light Flashing red-green
Communication mode Fluttering red
Fault codes LMO14/24
When the red light for a blocked relay box comes on, you can get
information about what has caused the problem by pressing and
holding the reset button for 3 seconds.
The number of ashes below is repeated with a pause in between.
2 ashes No ame signal when safety time
expires
4 ashes False light during start
7 ashes 3 x Losses of ame during operation
8 ashes Time-out for preheater *
10 ashes Incorrect wiring, internal fault or si-
multaneous occurrence of two faults
* In order for this fault code to occur, the preheater shall not reach
its cut-off temperature within 10 mins. from switch on.
To return to normal operation: Press the reset button for 1 second.
If the reset button is instead kept pressed a second time for at least
3 seconds, you can, via an interface, obtain the corresponding in-
formation on a computer or ue gas analyser.
To return to normal operation: Press the reset button for 1 second
ELECTRIC EQUIPMENT
3(3)

171 505 45 09-01
INSTRUCTIONS PUMP TYPE SUNTEC A2L 65C - 75C
Suction line tables
The suction line tables consist of theo-
retically calculated values where the
pipe dimensions and oil velocity have
been matched so that tur-bulences will
not occur. Such tur-bulences will result
in increased pressure losses and in
acoustic noise in the pipe system. In
addition to drawn copper piping a pipe
system usually comprises 4 elbows, a
non-return valve, a cut-off valve and
an external oil lter.
The sum of these individual resi-
stances is so insignicant that they
can be disregarded. The tables do not
include any lengths exceeding 100
m as experience shows that longer
lengths are not needed.
The tables apply to a standard fuel
oil of normal commercial quality
accor-ding to current standards. On
commis- sioning with an empty tube
system the oil pump should not be
run without oil for more than 5 min.
(a condition is that the pump is being
lubricated during operation).
The tables state the total suction line
length in metres at a nozzle capacity
of 9,5 Gph. Max. permissible pres-
sure at the suction and pressure side
is 2,0 bar.
Components
1. Nozzle outlet G 1/8" Stage 2
2. Pressure gauge port G 1/8"
3. Nozzle outlet G 1/8" Stage 1
4. Pressure gauge port G 1/8"
5. Vacuum gauge port G 1/8"
6. Return line G 1/4"
and internal by-pass plug
7. Suction line G 1/4"
8. Return plug
9. Pressure adjustment
10. Solenoid valve 1
11. Solenoid valve 2
Technical data
One or two-pipe system.
Viscosity range: 2-12 mm2/S
Pressure range: 8-15 bar
Rated voltage of coil: 220/240V
50/60 Hz
Oil temperature: max 60°C
1-pipe system
Height Pipe diameter
H ø6 mm
m m
With an underlying tank a 1-pipe-
system is not recommended
Two-pipe system
Height Pipe diameter
H ø8mm ø10mm ø12mm ø14mm
m m m m m
0,0 20 54 116 150
-0,5 17 48 103 150
-1,0 15 41 89 150
-2,0 9 28 61 116
-3,0 4 14 33 65
-4,0 0 0 6 14
1-pipe system
Height Pipe diameter
H ø6 mm ø8 mm ø10 mm
m m m m
4,0 45 144 150
3,0 39 127 150
2,0 34 109 150
1,0 28 92 150
0,5 26 83 150
0,0 23 74 150
Two-pipe system
Height Pipe diameter
H ø8mm ø10mm ø12mm ø14mm
m m m m m
4,0 42 108 150 150
3,0 36 94 150 150
2,0 31 81 150 150
1,0 26 68 144 150
0,5 23 61 130 150
0,0 20 54 116 150
H
H

171 505 46 09-01
Two pipe installation One pipe installation
Oil under
pressure
Oil under
suction
By-passed
oil returned
to tank,or
to suction
INSTRUCTIONS PUMP TYPE SUNTEC A2L 65C - 75C
Pump operating principle for
A2L 65C - 75C
The SUNTEC A2L oil pump has two
nozzle outlets. It incorporates two
blocking solenoid valves with in-line-
cut-off function, one for each nozzle
outlet.
The gear set draws oil from the tank
through the built-in lter and transfers
it to the nozzle line via the cut-off so-
lenoid valves. A pressure regulating
valve is used to dump all oil which is
not required at the nozzle.
In one-pipe operation, the oil which
does not go through the nozzle lines is
returned directly to the gear inlet and
the suction line ow is equal to the
sum of the 2 nozzle ows. In two-pipe
operation, the by-pass plug must be
tted in the return port, which ensures
that the oil dumped by the regulating
valve is returned to the tank and the
suction line ow is equal to the gear
set capacity.
Bleed
Bleeding in two-pipe operation is au-
tomatic: it is assured by a bleed at
on the piston. In one-pipe operation,
a high pressure connection must be
loosened until the air is evacuated
from the system.
Cut-Off
The solenoid valves of the A2L pump
are of the "normally closed" type and
are situated in the nozzle lines. This
design ensures extremely fast res-
ponse and the switching can be sel-
ected according to the burner opera-
ting sequence and is independant of
motor speed.
When the solenoids are non-activated,
the valves are closed and all oil
pressurised by the gear set passes
through the regulator to suction or to
the return line, depending upon pipe
arrangement.
As soon as the solenoids are activat-
ed, oil passes to the nozzle lines at
the pressure set by the pressure
regulating valve.
A2L C
XX
Shaft rotation and nozzle
location seen from shaft end
Gear set capacity
A2L: 2 nozzle outlets
Exchange of lter Mounting/dismounting return plug
One pipe system
Two pipe system
Solenoid valve 2 (NC) closed
Solenoid valve 2
(NC) open
Solenoid valve 1
(NC) open
To nozzle 2 To nozzle 1
Pressure
gauge port
Pressure
gauge port Shaft seal
By-pass
plug
Return
Suction
By-pass plug
removed
Solenoid valve 1 (NC) closed
Gear set
Vacuum gauge port
Pressure adjustment
Return
plugged
Back to suction

171 505 44 07-01
Gph 8 9 10 11
kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h
0,40 1,33 16 13 1,41 17 14 1,49 18 15 1,56 18 16
0,50 1,66 20 17 1,76 21 18 1,86 22 19 1,95 23 20
0,60 2,00 24 20 2,12 25 22 2,23 26 23 2,34 28 24
0,65 2,16 26 22 2,29 27 23 2,42 29 25 2,54 30 26
0,75 2,49 29 25 2,65 31 27 2,79 33 28 2,93 35 30
0,85 2,83 33 29 3,00 36 31 3,16 37 32 3,32 39 34
1,00 3,33 39 34 3,53 42 36 3,72 44 38 3,90 46 40
1,10 3,66 43 37 3,88 46 39 4,09 48 42 4,29 51 44
1,20 3,99 47 41 4,24 50 43 4,47 53 46 4,68 55 48
1,25 4,16 49 42 4,40 52 45 4,65 55 47 4,88 58 50
1,35 4,49 53 46 4,76 56 48 5,02 59 51 5,27 62 54
1,50 4,98 59 51 5,29 63 54 5,58 66 57 5,85 69 60
1,65 5,49 65 56 5,82 69 59 6,14 73 63 6,44 76 66
1,75 5,82 69 59 6,18 73 63 6,51 77 66 6,83 81 70
2,00 6,65 79 68 7,06 84 72 7,45 88 76 7,81 93 80
2,25 7,49 89 76 7,94 94 81 8,38 99 85 8,78 104 89
2,50 8,32 99 85 8,82 105 90 9,31 110 95 9,76 116 99
2,75 9,15 108 93 9,71 115 99 10,24 121 104 10,73 127 109
3,00 9,98 118 102 10,59 126 108 11,16 132 114 11,71 139 119
3,50 11,65 138 119 12,35 146 126 13,03 154 133 13,66 162 139
4,00 13,31 158 136 14,12 167 144 14,89 176 152 15,62 185 159
4,50 14,97 177 153 15,88 188 162 16,75 198 171 17,57 208 179
5,00 16,64 197 170 17,65 209 180 18,62 221 190 19,52 231 199
5,50 18,30 217 187 19,42 230 198 20,48 243 209 21,47 255 219
6,00 19,97 237 204 21,18 251 216 22,34 265 228 23,42 278 239
6,50 21,63 256 220 22,94 272 234 24,20 287 247 25,37 301 259
7,00 23,29 276 237 24,71 293 252 26,06 309 266 27,33 324 279
7,50 24,96 296 254 26,47 314 270 27,92 331 285 29,28 347 298
8,00 26,62 316 271 28,24 335 288 29,79 353 304 31,23 370 318
8,50 28,28 335 288 30,00 356 306 31,65 375 323 33,18 393 338
9,00 29,95 355 305 31,77 377 324 33,59 398 342 35,14 417 358
NOZZLE TABLE
Pump pressure bar
The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.
Burner with preheater
Consider that on preheating the oil quantity is reduced by 5-20% depending on.
- Rise in temperature at the nozzle
- Design of nozzle
- Capacity (high capacity - small difference)
1(2)

171 505 44 07-01
Gph 12 13 14 15
kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h
0,40 1,63 19 17 1,70 20 17 1,76 21 18 1,82 21 18
0,50 2,04 24 21 2,12 25 22 2,20 26 22 2,28 27 23
0,60 2,45 29 25 2,55 30 26 2,64 31 27 2,73 32 28
0,65 2,65 31 27 2,75 33 28 2,86 34 29 2,96 35 30
0,75 3,08 36 31 3,18 38 32 3,30 39 34 3,42 40 35
0,85 3,47 41 35 3,61 43 37 3,74 44 38 3,87 46 39
1,00 4,08 48 42 4,24 50 43 4,40 52 45 4,56 54 46
1,10 4,48 53 46 4,67 55 48 4,84 57 49 5,01 59 51
1,20 4,89 58 50 5,09 60 52 5,29 63 54 5,47 65 56
1,25 5,10 60 52 5,30 63 54 5,51 65 56 5,70 68 58
1,35 5,50 65 56 5,73 68 58 5,95 70 61 6,15 73 63
1,50 6,11 72 62 6,36 75 65 6,60 78 67 6,83 81 70
1,65 6,73 80 69 7,00 83 71 7,27 86 74 7,52 89 77
1,75 7,14 85 73 7,42 88 76 7,71 91 79 7,97 94 81
2,00 8,18 97 83 8,49 101 86 8,81 104 90 9,12 108 93
2,25 9,18 109 94 9,55 113 97 9,91 117 101 10,26 122 105
2,50 10,19 121 104 10,61 126 108 11,01 130 112 11,39 135 116
2,75 11,21 133 114 11,67 138 119 12,11 144 123 12,53 148 128
3,00 12,23 145 125 12,73 151 130 13,21 157 135 13,67 162 139
3,50 14,27 169 145 14,85 176 151 15,42 183 157 15,95 189 163
4,00 16,31 193 166 16,97 201 173 17,62 209 180 18,23 216 186
4,50 18,35 217 187 19,10 226 195 19,82 235 202 20,51 243 209
5,00 20,39 242 208 21,22 251 216 22,03 261 225 22,79 270 232
5,50 22,43 266 229 23,34 277 238 24,23 287 247 25,07 297 256
6,00 24,47 290 249 25,46 302 260 26,43 313 269 27,49 326 280
6,50 26,51 314 270 27,58 327 281 28,63 339 292 29,63 351 302
7,00 28,55 338 291 29,70 352 303 30,84 366 314 31,91 378 325
7,50 30,59 363 312 31,83 377 324 33,04 392 337 34,19 405 349
8,00 32,63 387 333 33,95 403 346 35,25 418 359 36,47 432 372
8,50 34,66 411 353 36,07 428 368 37,45 444 382 38,74 459 395
9,00 36,71 435 374 38,19 453 389 39,65 470 404 41,02 486 418
NOZZLE TABLE
The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.
Burner with preheater
Consider that on preheating the oil quantity is reduced by 5-20% depending on.
- Rise in temperature at the nozzle
- Design of nozzle
- Capacity (high capacity - small difference)
2(2)
Pump pressure bar

171 505 40 07-01
Gph 10 11 12 13
kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h
1,00 3,72 44 38 3,90 46 40 4,08 48 42 4,24 50 43
1,10 4,09 48 42 4,29 51 44 4,48 53 46 4,67 55 48
1,20 4,47 53 46 4,68 55 48 4,89 58 50 5,09 60 52
1,25 4,65 55 47 4,88 58 50 5,10 60 52 5,30 63 54
1,35 5,02 59 51 5,27 62 54 5,50 65 56 5,73 68 58
1,50 5,58 66 57 5,85 69 60 6,11 72 62 6,36 75 65
1,65 6,14 73 63 6,44 76 66 6,73 80 69 7,00 83 71
1,75 6,51 77 66 6,83 81 70 7,14 85 73 7,42 88 76
2,00 7,45 88 76 7,81 93 80 8,16 97 83 8,49 101 87
2,25 8,38 99 85 8,78 104 90 9,18 109 94 9,55 113 97
2,50 9,31 110 95 9,76 116 100 10,19 121 104 10,61 126 108
2,75 10,24 121 104 10,73 127 109 11,21 133 114 11,67 138 119
3,00 11,16 132 114 11,71 139 119 12,23 145 125 12,73 151 130
3,50 13,03 154 133 13,66 162 139 14,27 169 146 14,85 176 151
4,00 14,89 176 152 15,62 185 159 16,31 193 166 16,97 201 173
4,50 16,75 199 171 17,57 208 179 18,35 218 187 19,10 226 195
5,00 18,62 220 190 19,52 231 199 20,39 242 208 21,22 252 216
5,50 20,48 243 209 21,47 255 219 22,43 266 229 23,34 277 238
6,00 22,34 265 228 23,42 278 239 24,47 290 250 24,46 302 260
6,50 24,20 287 247 25,37 301 259 26,51 314 270 27,58 327 281
7,00 26,06 309 266 27,33 324 279 28,55 339 291 29,70 352 303
7,50 27,92 331 285 29,28 347 299 30,59 363 312 31,83 377 325
8,00 29,79 353 304 31,23 370 318 32,63 387 333 33,95 403 346
8,50 31,65 375 323 33,18 393 338 34,66 411 353 36,07 428 368
9,00 33,59 398 343 35,14 417 358 63,71 435 374 38,19 453 389
9,50 35,37 419 361 37,09 440 378 38,74 549 395 40,31 478 411
10,00 37,23 441 380 39,04 463 398 40,78 484 416 42,44 503 433
11,00 40,96 486 418 42,94 509 438 44,86 532 457 46,68 554 476
12,00 44,68 530 456 46,85 556 478 48,94 580 499 50,92 604 519
14,00 52,12 618 531 54,65 648 557 57,10 677 582 59,41 705 606
16,00 59,57 706 607 62,46 741 637 65,26 774 666 67,90 805 692
18,00 67,02 795 683 70,27 833 717 73,41 871 749 76,39 906 779
20,00 74,47 883 759 78,08 926 796 81,57 967 832 84,87 1007 865
22,00 81,91 971 835 85,89 1019 876 89,73 1064 915 93,36 1107 952
24,00 89,36 1060 911 93,70 1111 956 97,88 1161 998 101,85 1208 1039
26,00 96,81 1148 987 101,50 1204 1035 106,04 1258 1081 110,33 1308 1168
NOZZLE TABLE
Pump pressure bar
The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.
1(2)

171 505 40 07-01
Gph 14 15 16 17
kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h
1,00 4,40 52 45 4,56 54 46 4,71 56 48 4,85 57 49
1,10 4,84 57 49 5,01 59 51 5,18 61 53 5,34 63 54
1,20 5,29 63 54 5,47 65 56 5,65 67 58 5,82 69 59
1,25 5,51 65 56 5,70 68 58 5,89 70 60 6,07 72 62
1,35 5,95 70 61 6,15 73 63 6,36 75 65 6,55 78 67
1,50 6,60 78 67 6,83 81 70 7,06 84 72 7,27 86 74
1,65 7,27 86 74 7,52 89 77 7,77 92 79 8,01 95 82
1,75 7,71 91 79 7,97 95 81 8,24 98 84 8,49 101 87
2,00 8,81 104 90 9,12 108 93 9,42 112 96 9,71 115 99
2,25 9,91 118 101 10,26 122 105 10,60 126 108 10,92 130 111
2,50 11,01 131 112 11,39 135 116 11,77 140 120 12,13 144 124
2,75 12,11 144 123 12,53 149 128 12,95 154 132 13,35 158 136
3,00 13,21 157 135 13,67 162 139 14,13 168 144 14,56 173 148
3,50 15,42 183 157 15,95 189 163 16,49 196 168 16,99 201 173
4,00 17,62 209 180 18,23 216 186 18,84 223 192 19,42 230 198
4,50 19,82 235 202 20,51 243 209 21,20 251 216 21,84 259 223
5,00 22,03 261 225 22,79 270 232 23,55 279 240 24,27 288 247
5,50 24,23 287 247 25,07 297 256 25,91 307 264 26,70 317 272
6,00 26,43 313 270 27,49 326 280 28,27 335 288 29,13 345 297
6,50 28,63 340 292 29,63 351 302 30,62 363 312 31,55 374 322
7,00 30,84 366 314 31,91 378 325 32,98 391 336 33,98 403 374
7,50 33,04 392 337 34,19 405 349 35,33 419 360 36,41 432 371
8,00 35,25 418 359 36,47 433 372 37,69 447 384 38,80 460 396
8,50 37,45 444 382 38,74 459 395 40,04 475 408 41,26 489 421
9,00 39,65 470 404 41,02 486 418 42,40 503 432 43,69 518 446
9,50 41,85 496 427 43,30 514 442 44,75 531 456 46,11 547 470
10,00 44,06 523 449 45,58 541 465 47,11 559 480 47,11 559 480
11,00 48,46 575 494 50,14 595 511 51,82 615 528 53,40 633 545
12,00 52,87 627 539 54,70 648 558 56,53 670 576 58,25 691 594
14,00 62,68 732 629 63,81 757 651 65,95 778 669 67,96 806 693
16,00 70,49 836 719 72,93 865 744 75,38 894 769 77,67 921 792
18,00 79,30 940 809 82,05 973 837 84,80 1006 865 87,38 1036 891
20,00 88,11 1045 899 91,17 1081 930 94,22 1117 961 97,09 1151 990
22,00 96,92 1149 988 100,28 1189 1023 103,64 1229 1057 106,79 1267 1089
24,00 105,74 1254 1078 109,40 1297 1116 113,06 1341 1153 116,50 1382 1188
26,00 114,55 1359 1168 118,52 1406 1209 122,49 1453 1249 126,21 1497 1287
NOZZLE TABLE
2(2)
Pump pressure bar
The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.

171 505 41 07-01
Gph 18 19 20 21
kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h
1,00 4,99 59 51 5,13 61 52 5,26 62 54 5,40 64 55
1,10 5,49 65 56 5,64 67 57 5,79 69 59 5,93 70 60
1,20 5,99 71 61 6,16 73 63 6,32 75 64 6,47 77 66
1,25 6,24 74 64 6,41 76 65 6,58 78, 67 6,74 80 69
1,35 6,74 80 69 6,93 82 71 7,11 84 72 7,28 86 74
1,50 7,48 89 76 7,69 91 78 7,89 93 80 8,08 96 82
1,65 8,24 98 84 8,47 100 86 8,69 103 89 8,90 105 91
1,75 8,78 104 90 8,98 106 92 9,21 109 94 9,44 112 96
2,00 9,99 118 102 10,26 122 105 10,53 125 107 10,79 128 110
2,25 11,24 133 115 11,55 137 118 11,85 140 121 12,14 144 124
2,50 12,48 148 127 12,83 152 131 13,16 156 134 13,49 160 138
2,75 13,73 163 140 14,11 167 144 14,48 171 148 14,84 176 151
3,00 14,98 178 153 15,39 182 157 15,79 187 161 16,18 192 165
3,50 17,48 207 178 17,96 213 183 18,43 218 188 18,89 224 193
4,00 19,98 237 204 20,53 243 209 21,06 250 215 21,59 256 220
4,50 22,47 266 229 23,09 274 235 23,69 281 242 24,28 288 248
5,00 24,97 296 255 25,65 304 262 26,33 312 268 26,98 320 275
5,50 27,47 326 280 28,22 335 288 28,96 343 295 29,68 352 303
6,00 29,97 355 306 30,79 365 314 31,59 374 322 32,38 384 330
6,50 32,46 385 331 33,35 395 340 34,22 406 349 35,07 416 358
7,00 34,96 415 356 35,92 426 366 36,86 437 376 37,77 448 385
7,50 37,46 444 382 38,49 456 392 39,49 468 403 40,47 480 413
8,00 39,96 474 407 41,05 487 419 42,12 499 429 43,17 512 440
8,50 42,45 503 433 43,62 517 445 44,75 531 456 45,87 544 468
9,00 44,95 533 458 46,18 548 471 47,39 562 483 48,57 576 495
9,50 47,45 563 484 48,75 578 497 50,02 593 510 51,26 608 523
10,00 49,94 592 509 51,32 609 523 52,66 624 537 53,96 640 550
11,00 54,94 652 560 56,45 669 576 57,92 687 591 59,36 704 605
12,00 59,93 711 611 61,58 730 628 63,19 749 644 64,76 768 660
14,00 69,92 829 713 71,84 852 733 73,72 874 752 75,55 896 770
16,00 79,91 948 815 82,11 974 837 84,25 999 859 86,34 1024 880
NOZZLE TABLE
Pump pressure bar
The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.
1(2)

171 505 41 07-01
Gph 22 23 24 25
kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h kg/h kW Mcal/h
1,00 5,53 66 56 5,65 67 58 5,77 68 59 5,89 70 60
1,10 6,07 72 62 6,21 74 63 6,34 75 65 6,47 77 66
1,20 6,62 78 67 6,77 80 69 6,92 82 71 7,06 84 72
1,25 6,90 82 70 7,05 84 72 7,21 85 73 7,35 87 75
1,35 7,45 88 76 7,62 90 78 7,78 92 79 7,94 94 81
1,50 8,27 98 84 8,46 100 86 8,64 102 88 8,82 105 90
1,65 9,11 108 93 9,31 110 95 9,51 113 97 9,71 115 99
1,75 9,66 115 98 9,88 117 101 10,09 120 103 10,30 122 105
2,00 11,04 131 113 11,29 134 115 11,53 137 118 11,77 140 120
2,25 12,43 147 127 12,70 151 129 12,98 154 132 13,25 157 135
2,50 13,81 164 141 14,12 167 144 14,42 171 147 14,72 175 150
2,75 15,19 180 155 15,53 184 158 15,86 188 162 16,19 192 165
3,00 16,18 192 165 16,93 201 173 17,30 205 176 17,65 209 180
3,50 19,33 229 197 19,77 234 202 20,19 239 206 20,61 244 210
4,00 22,10 262 225 22,59 268 230 23,08 274 235 23,56 279 240
4,50 24,85 295 253 25,41 301 259 25,96 308 265 26,49 314 270
5,00 27,61 327 282 28,24 335 288 28,84 342 294 29,44 349 300
5,50 30,38 360 310 31,06 368 317 31,73 376 324 32,38 384 330
6,00 33,14 393 338 33,89 402 346 34,62 411 353 35,33 419 360
6,50 35,90 426 366 36,70 435 374 37,49 445 382 38,26 454 390
7,00 38,56 457 393 39,53 469 403 40,38 479 412 41,21 489 420
7,50 41,42 491 422 42,35 504 434 43,26 513 441 44,16 524 450
8,00 44,19 524 451 45,18 536 461 46,15 547 471 47,10 559 480
8,50 46,95 557 479 48,00 569 489 49,03 581 500 50,05 594 510
9,00 49,71 589 507 50,83 603 518 51,92 616 529 52,99 628 540
9,50 52,47 622 535 53,65 636 547 54,80 650 559 55,93 663 570
10,00 55,23 655 563 56,47 670 576 57,69 684 588 58,88 698 600
11,00 60,76 721 620 62,12 737 633 63,46 753 647 64,77 768 660
12,00 66,28 786 676 67,77 804 691 69,23 821 706 70,66 838 721
14,00 77,33 917 789 79,09 938 806 80,77 958 824 82,43 978 841
16,00 88,37 1048 901 90,36 1072 921 92,30 1095 941 94,20 1117 961
NOZZLE TABLE
2(2)
Pump pressure bar
The table applies to oil with a viscosity of 4,4 mm2/s (cSt) with density 830 kg/m3.

FAULT LOCATION
Burner fails to start
Delayed ignition, burners starts violently
Burner fails to start after normal operation
Situation
Motor runs
Burner pre-purges
Flame occurs
Burner locks out
Motor runs
Burner pre-purges
No ame occurs
Burner locks out
Possible causes
Flame instability
Incorrect head settings
Low oil pressure
Excess air
Photocell not seeing light
Photocell failed
Control faulty
False light
No spark
No oil
Remedies
Check nozzle to burner head dimension
and electrode position
Check oil pressure
Adjust air damper
Check that photocell is clean and
unobstructed
Conrm with new photocell
Conrm with new control. (NB. it is
advisable to change the photocell if also
changing control)
Check that photocell is not seeing
ambient light
Check that H.T. leads are sound and are
not arcing other than at electrode gap
Check oil supply to burner - check that
pump is not airlocked
Check operation of magnetic valve
Burner fails to start
Lamp not lit
Motor runs
Burner runs to lockout
Fuse has blown
Appliance thermostat has not reset
Appliance overheat device has operated
Control relay or photocell defective
No oil being delivered
Excessive ue draught is preventing
ame establishment
No spark
Check or replace fuse if necessary.
Check reason for failure
Adjust thermostat
Reset overheat device. Find reason for
its operation and rectify
Check by replacement
Check that tank, oil lines, re valve, pump
and nozzle are all in good order
Rectify condition
Check ignition transformer. Check
electrode gap and porcelain
Burner pulsates on start-up
only with hot ue
Burner pulsates on start-up
Burner starts violently
Excessive draught
Nozzle partly blocked
Oil pressure too low
Flue blocked or damaged
Fan slipping on shaft
Pump coupling loose or worn
Delayed ignition
Adjust the burner
Replace nozzle
Check and adjust
Check and rectify
Check and retighten
Check and replace
Check the electrode adjustment, see
diagram
Check electrodes for damage
Check H.T. leads for damage and
disconnection
171 915 01 08-01