EnGenius ENS202v2 User manual

User Manual
Business Solutions
N300 2.4GHz Outdoor AP
ENS202v2 / ENS202EXTv2
version 1.0

2
IMPORTANT
To install this Access Point please refer to the
Quick Installation Guide included in the product packaging.

3
Chapter 1 Product Overview...................................................................... 4
Key Features/Introduction.................................................................5
System Requirements..........................................................................6
Package Contents..................................................................................6
Software Features................................................................................7
Physical Interface...................................................................................8
Chapter 2 Before You Begin....................................................................... 9
Computer Settings.............................................................................. 10
Hardware Installation.........................................................................14
Mounting the AP...................................................................................15
Chapter 3 Conguring Your Access Point............................................17
Default Settings/Web Conguration............................................18
Chapter 4 Building a Wireless Network................................................19
Access Point ......................................................................................... 20
Clien Bridge Mode............................................................................... 21
WDS AP Mode.......................................................................................22
WDS Bridge Mode................................................................................23
WDS Station Mode..............................................................................24
Chapter 5 Status............................................................................................25
Overview..................................................................................................26
Connection..............................................................................................29
Chapter 6 Network ......................................................................................31
Basic IP Settings...................................................................................32
Spanning Tree Protocol Setting.....................................................33
Chapter 7 2.4 GHz Wireless..........................................................................34
Wireless Settings..................................................................................35
2.4 GHz Wireless Network................................................................36
Wireless Security..................................................................................39
Fast Roaming.........................................................................................42
Wireless Trafc Shaping.................................................................. 44
Wireless MAC Filteing.........................................................................43
Guest Network Settings.................................................................. 45
RSSI Threshold......................................................................................46
Manegement VLAN Settings...........................................................47
Chapter 8 Management ............................................................................... 48
Advanced Settings............................................................................. 49
CLI/SSH/HTTPS Settings/Email Alr..............................................50
Time Zone..............................................................................................52
Auto Reboot Settings........................................................................53
Wi-Fi Scheduler....................................................................................54
Tools........................................................................................................ 55
Account/Firmware...............................................................................57
Backup/Restore Setting....................................................................58
Log.............................................................................................................60
Logout/Reset.........................................................................................61
Appendix..............................................................................................................62
FCC Interference Statement...........................................................63
IC Interference Statement...............................................................64
CE Interference StatEment..............................................................66
Table of Contents

4
Chapter 1
Product Overview

5
Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, distance between
devices, radio interference in the operating environment, and mix of devices in the network. Features and specications subject to change without notice. Trademarks and registered
trademarks are the property of their respective owners. For United States of America: Copyright © 2018EnGenius Technologies, Inc. All rights reserved.
Key Features
• Supports IEEE802.11b/g/n wireless standards with up to 300
Mbps data rate on 2.4GHz band
• Two detachable 5 dBi 2.4 GHz Omni-dipole antennas with
ENS202EXT.
• Can be used with included power adapter or via PoE with
Proprietary 24V.
• Fast Transition and Handover between Access Points
• Secured Guest Network option available
Introduction
ENS202/ENS202EXT supports Power over Ethernet and
Power by Adapter capabilities, which allow the device to
be installed easily in nearly any indoor or outdoor location.
Also, ENS202EXT provides not only detachable antenna
connectors for antenna upgrade, but also high output
power and high sensitivity can extend the transmisson
range to deliver a stable wireless connection. ENS202EXT
integrates 4 operation modes: Access Point, Client Bridge
and WDS.
Advance multi-function operation modes offer exibility
in constructing scalable wireless networks for all possible
applications. ENS202EXT is designed to deliver reliable
service under harsh outdoor envirnment with certied
IP65 protection and tailored to accommodate multimedia
Introduction
streaming services withdata-rate up to300Mbps. Advanced
features include power level control, trafc shapping, and
Real time RSSI indication.
Mostimportantly,it isbuilt-inencryptionstandards,including
Wi-Fi Protected Access (WPA2-PSK) Encryption, and IEEE
802.1x with RADIUS.

6
System Requirements
The following are the Minimum System Requirements in
order to congure the device.
• Computer with an Ethernet interface or wireless network
capability.
• Windows OS(XP, Vista, 7, 8, 10), Mac OS, or Linux-based
operating systems
• Web-Browsing Application (i.e.: Internet Explorer, Firefox,
Safari, or another similar browser application).
Package Contents
The ENS202/ENS202EXT package contains the following
items:*
• ENS202/ENS202EXT Access Point
• 2 detachable 5 dBi 2.4 GHz Omni Antenna-ENS202EXT only
• PoE Adapter (24V/0.6A)
• Wall Mount Kit (Screw set & Adhensive Label)
• Pole Mount kit (Cable Tie*2)
• Quick Installation Guide
*(all items must be in package to issue a refund)

7
Multicast Supported
Auto Reboot
Obey Regulatory Power
Security
WPA2 Personal
WPA2 Enterprise
Hides SSID in beacons
MAC address ltering, up to 32 MACs
Wireless STA (Client) connection list
Https Support
SSH Support
QoS (Quality of Service)
Complaint with IEEE 802.11e standard
Standard:
IEEE802.11b/g/n on 2.4 GHz
IEEE802.3u(100BASE-TX)/IEEE802.3(10BASE-T)
Operation Modes
Access Point
Client Bridge
WDS
WDS Detail
WDS AP
WDS Bridge
WDS Station
Management
Auto Channel Selection
Multiple SSID: 8 SSIDs per Radio
BSSID
SNMP V1/V2c/V3
MIB I/II, Private MIB
VLAN Tag/VLAN Pass-through
Clients Statistics
Save Conguration as User Default
Fast Roaming
E-Mail Alert
RADIUS Accounting
Guest Network
Control
CLI Supported
Distance Control (Ack Timeout)
802.1X Supplicant (CB Mode)
Software Features

8
Physical Interface
Dimensions and Weights
With Antenna:100mm(4”)*37.5mm(1.375”)*205mm(8”)(W*D*H)
Weight: 242g
Without Antenna:100mm(4”)*37.5mm(1.375”)*189mm(7.375”)
(W*D*H)
Weight: 275g
1 2.4 GHz Antennas: Detachable 5 dBi 2.4 GHz Omni-ENS202EXT
only
2 LAN Port (Proprietary 24V PoE Input): Ethernet port for RJ-45
cable.
3 LED Indicators: LED lights for Power, LAN Port, 2.4 GHz
Connection
4 Mounting Holes: Using the provided hardware, the ENS202EXT
can be attached to a wall or pole.
Physical/Environment Conditions
Operating:
Temperature: -4 °F to 158 °F (-20 °C to 70 °C)
Humidity (non-condensing): 0%~90% typical
Storage:
Temperature: -40 °F to 176 °F (-40 °C to 80 °C)
Humidity (non-condensing): 0%~90% typical

9
Chapter 2
Before You Begin

10
Windows XP/Windows 7/Windows 8/Windows
10
In order to use the Access Point, you must rst congure the
TCP/IPv4 connection of your Windows OS computer system.
1a. Click the Start button and open the Control Panel
1b. Move your mouse to the lower right hot corner to
display the Charms Bar and select the Control Panel in
Windows 8 OS.
1c. In Windows 10, click Start to select All APPs to enter
the folder of Windows system for selecting Control
Panel.
Computer Settings
Windows XP Windows 7
Windows 8
Windows 10

11
2a.In Windows XP, click Network Connections.
2b.In Windows 7/Windows 8/Windows 10, click View
Network Status and Tasks in the Network and
Internet section, then select Change adapter settings.
3. RightclickonLocalAreaConnectionandselectProperties.
4. Select Internet Protocol Version 4 (TCP/IPv4) and then
select Properties.
5. Select Use the following IP address and enter an IP
address that is different from the Access Point and Subnet
mask, then click OK.

12
Note: Ensure that the IP address and Subnet mask are
on the same subnet as the device.
For example: ENH220EXT IP address: 192.168.1.1
PCIPaddress:192.168.1.2–192.168.1.255
PC Subnet mask: 255.255.255.0

13
Apple Mac OS X
1. Go to System Preferences (Which can be opened in the
Applications folder or selecting it in the Apple Menu).
2. Select Network in the Internet & Network section.
3. Highlight Ethernet.
4. In Congure IPv4, select Manually.
5. Enter an IP address that is different from the Access
Point and Subnet mask then press OK.
Note: Ensure that the IP address and Subnet mask are
on the same subnet as the device.
For example: ENH900EXT IP address: 192.168.1.1
PCIPaddress:192.168.1.2–192.168.1.255
PC Subnet mask: 255.255.255.0
6. Click Apply when done.

14
1. Connect one end of the Ethernet cable into the LAN port
(PoE) of the AP/ Bridge and the other end to the PoE
port on the PoE adapter.
2. Connect the Power cord with the PoE Adapter and plug
the other end into an electrical outlet.
3. Connect the second Ethernet cable into the LAN port of
the PoE adapter and the other end to the Ethernet port
on the computer.
4. Screw on the provided antennas to the top of this device.
Note: The AP/Bridge should ONLY be powered via
Ethernet cable connected to the included PoE Adapter.
This diagram depicts the hardware conguration.
Note: The AP/Bridge should ONLY be powered via
Ethernet cable connected to the included PoE Adapter.
Hardware Installation
Ethernet
PC
Power
Outlet
PoE Adapter

15
Mounting the ENS202/ENS202EXT
Using the provided hardware, the ENS202EXT can be attached to a wall or a pole. The height should not exceed 2 meter.
1. Wall Mounting Kit
(Anchors:Φ5.5*18mm&Bolts:Φ8*25mm)
2. Pole Mounting Strap
(Φ66*12.6 mm)
Anchors Bolts

16
To attach the ENS202EXT/ENS202EXT to a wall
using wall mounting kit.
A. Determine where the Access Point to be placed and
stick the Adhesive label on the surface.
B. Use the appropriate drill bit to drill two 8.1mm
diagram and 26mm depth holes on the markings of the
label.
C. Remove the label and screw the anchors unto the holes
until they are ush with the wall.
D. Screw the included screws into the anchors. Place the
Access Point against wall with the mounting screw heads.
To attach the ENS202EXT to a pole using the
provided pole mounting kit:
A. Thread the open end of the Pole Strap through the two
tabs on the Pole Mount Bracket.
B.Lock and tighten Pole Strap to secure Pole Mount Bracket
to the pole.

17
Chapter 3
Conguring Your
Access Point

18
This section will show you how to congure the device
using the web-based conguration interface.
Default Settings
Please use your Ethernet port or wireless network adapter
to connect the Access Point.
IP Address 192.168.1.1
Username / Password admin / admin
Web Conguration
1. Open a web browser (Internet Explorer/Firefox/Safari/
Chrome) and enter the IP Address http://192.168.1.1
Note: If you have changed the default LAN IP Address of
the Access Point, ensure you enter the correct IP Address.
2. The default username and password are admin.
Once you have entered the correct username and
password, click the Login button to open the web-base
conguration page.
*The model name will be varied by different models.
3. If successful, you will be logged in and see the User
Menu of this Access Point.
*The model name will be varied by different model
Conguring Your Access Point

19
Chapter 4
Building a Wireless
Network

20
Before starting to congure this Access Point, you may realize the used scenario under varied operating modes.The AP
has the ability to operate in various modes. This chapter describes purpose of different operating modes and lists down
the operating modes for outdoor Access Points.
Access Point Mode
In Access Point Mode, AP behaves likes a central connection for stations or clients that support IEEE 802.11ac/a/b/g/n networks.
The stations and clients must be congured to use the same SSID (Service Set Identier) and security password to associate
with the AP. The AP supports up to eight SSIDs at the same time for secure access.
AP
Access Point
Client
Client Client
Client Client
Client
2.4 GHz 5 GHz