enLighten Tauro Eco HB80-5000 Series User manual

Tauro EcoTM
LED HIGH BAY/ LOW BAY LED LIGHTS
INSTALLATION INSTRUCTIONS
EASY INSTALLATION
Comes with 3m Australian Flex and Plug and eye bolts as standard.
A mouting bracket is available as an optional extra.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1.
2.
To avoid the possibility of electrical shock, turn offpower supply before
installaon or servicing. Installaon and servicing should be performed
by a qualified electrician and in accordance the latest wiring regulations.
Light must be operated within its specified operating parameters and in
accordance with our warranty requirements.
These documents are available on our website.
TO INSTALL:
Model No.
HB80-5000-xx
HB120-5000-xx
HB160-5000-xx
HB200-5000-xx
HB240-5000-xx
80W
120W
160W
200W
240W
Power
366 x340 x156 mm
439 x340 x156 mm
512 x340 x156 mm
585 x340 x156 mm
658 x340 x156 mm
Dimension
4.3 kg
5.2 kg
6.0 kg
7.0 kg
7.8 kg
Weight
100-240V/277V AC, 50/60Hz, Suitable for Wet Locaons (IP65), Class I
*This product must be earthed
xx denotes 60° / 90° / 110° degree beam angle
Optional Mounting
Bracket shown
STEP 3:
Connect the power plug to a mains power
socket.
SUSPENSION MOUNTING
STEP 1:
Attach your preferred hanging chain (not
supplied) to the four eye bolts on fitting.
STEP 2:
Secure hanging chain to ceiling.
Use one of the mouting methods described below
STEP 3:
Loosen the mounƟng bracket screws, adjust
the fixture to desiredposiƟon, re-secure the
screws.
STEP 4:
Connect the power plug to a mains power
socket.
PENDANT MOUNTING
STEP 1:
Assemble the mounƟng bracket to the fixture
by provided M10 (3/8”) round head screws.
STEP 2:
AƩach Lock-Nut(A) to the boƩom of the
Pendant Stem. AƩach Lock-Nut(B) by holding
the interjacent Fixture Bracket and Ɵghtening
Lock-Nut(B) unƟl secure. See Figure 1.
1 2
Look-Nut(A)*²
Look-Nut(B)*²
Pendant Stem*¹
Pendant Stem Thread
*¹ Pendant Stem can not be soŌmaterial (not-provided)
*² Look Nuts are not provided
Power Cord
(Cord Not shown)
Power Cord
(Cord Not shown)

Tighten bracket screws on both sides, luminaire
installaon angle will be fixed by the lock gear.
SURFACE MOUNTING
1
*¹ Minimum M10 (3/8”) Bolts (not-provided)
*² Mounng Nuts are not provided
*³ Allen Wrench: 8mm (5/16”)
2STEP 1:
Assemble the mounng bracket to the fixture
by provided M10 (3/8”) round head screws.
328 mm (12.91 inches)
40 mm (1.57 inches) Φ12 mm (0.47 inches)
138 mm (5.43 inches)
12 mm (0.47 inches)
Mounng Bracket
81 mm
(3.19 inches)
75 mm
(2.95 inches)
Luminaire
Mounng Holes For
Minimum M10 (3/8”)
Mounng Bolts
Pendant
Mounng
Hole
Waterproof Connector
1
Celling /Wall Mounng Bolts*¹
Mounng Nuts*²
Power Cord
(Cord Not shown)
Power Cord
(Cord Not shown)
Allen Wrench*³
STEP 2:
Mount the fixture by TWO(2) minimum M10
(3/8”) bolts. See Figure 1.
STEP 3:
Loosen the mounng bracket screws, adjust
the fixture to desiredposion, re-secure the
screws.
STEP 4:
Connect the power plug to a mains power
socket.