Enttec 70314 User manual

DMX USB Pro Controller MK II LS6970
LS6970 180205
Products and specifications are subject to change without notice 1
www.lumascape.com
User Manual
70314
For latest version visit:
www.enttec.com
1ID: 3647846
^ōɭȕǢDƻNJŷōħˡ
(PN 70314)
Box Contents
•PRO Mk2 (pn: 70314)
•Micro USB Cable (pn: 50282)
•DMX Breakout cable 0.1M - DB15 to 3x 5pin DMX
(pn: 79146)
•This user manual
Features
•Two universes (512 channel each) of input or
output (one per DMX port)
•Standalone mode: playback a single recorded
DMX show on power-up
•Midi input & output ports (DMX + MIDI cable sold
separately) – MIDI needs software support
•Fully compliant with USITT DMX512-A
•Adjustable Frame Rates and empty frames to
accommodate non-standard equipment
•USB 2.0 Support on Windows PC and Mac OSX
•1500 V full isolation (data & power lines to
protect your computer from surges)
•RDM enabled (ANSI E1.20 compliant)
•Drivers for Windows, OSX and Linux (drivers
released and maintained by FTDI)
•Output refresh rate configurable from 1 to 40 Fps
(Frames per second)
•Compatible with various open-source and
professional lighting control programs.
Safety
•Do not expose the PRO Mk2 to rain or moisture,
doing this will void the warranty
•Do not remove the cover, there are no serviceable
parts inside
•This unit is intended for indoor use only
•Wherever possible, use with a DMX Splitter for safety
and better reliability with DMX cables.
Basic Setup
•Install and configure the Driver software on your
Windows™, Linux™ or Mac™ computer.
•Methods can vary between Operating systems, but
the end result is the same: once installed correctly,
the drivers will allow software to communicate with
the PRO Mk2.
•Connect the PRO Mk2 to your computer (USB) and
the DMX512 control network (DMX cable).
•Load the control software of your choice onto the
computer. You can choose between open-source
(free) and professional (paid) programs. More
information is available at www.enttec.com/dmx
•Run the software and create your show.
•For troubleshooting, testing (DMX and MIDI) and
using standalone mode on PRO Mk2, install and run
PRO-Manager.

DMX USB Pro Controller MK II LS6970
LS6970 180205
Products and specifications are subject to change without notice 2
www.lumascape.com
User Manual
70314
For latest version visit:
www.enttec.com
2ID: 3647846
LED Status
PRO Mk2 comes with a RGB LED indicator located on the
top (above the usb connector). The LED will blink
between these colours, and each colour signifies the
related activity:
•White: PRO Mk2 is powered on and idle
•Green: DMX1 send or receive (DMX Port 1)
•Yellow: DMX2 send or receive (DMX Port 2)
•Blue: Standalone mode (show playback)
•Purple:MIDI in or out
•Red: error or unsupported request
At any given time, the PRO Mk2 led will blink amongst
a combination of these colours or just one of these
colours
It is advised to re-connect the usb cable if led is solid
red (not blinking) to reset the PRO Mk2.
If the led stays red – a restore might be required to
reset the PRO Mk2. Restore or firmware update can be
performed by PRO-Manager.
Install Drivers
PRO Mk2 is supported by FTDI drivers for the following
Operating Systems:
•Windows 10, Windows 8, Windows 7, Windows XP,
Windows Server 2003, Windows Vista, Windows
Server 2008, Windows Server 2008 R2. (32 bit and
64 bit versions)
•Mac OS X (Mac OS X 10.4 or later)
•Linux - Raspberry Pi is supported, others will
require driver or library (please check FTDI)
To proceed, you need the driver setup file, which is
available from:
•Download PRO-Manager (includes the
driver setup) from the ENTTEC website:
enttec.com/pro-manager
•For the latest drivers and OS support,
please visit FTDI website:
ftdichip.com/Drivers/D2XX.htm
Setting up on Windows
Execute the setup file and let the drivers install on your
Windows machine. If using PRO-Manager setup, click Yes
when prompted to install FTDI Drivers
Click on Extract, and follow the setup procedure by clicking
Next. It will go through the drivers install process and copy
the needed files.
Once done it will show the completion screen, highlighting
that the drivers have been installed correctly
In most cases the USB port you plug the DMX USB PRO into
will automatically fall into an acceptable range with respect
to the other elements of your computer’s communications
ports, but if you are having problems or conflicts between
the ports, here is what you can do to change the COM port.
Before making any changes. it is advisable to keep a record
of which serial port has been used in each attempt to
configure the hardware and drivers. That way you will be
able to retrace your steps should you decide to go back and
try something again but with different settings elsewhere.
Device Manager
Open Device Manager on your Windows machine. (Control
Panel → Device Manager)
Expand the “Ports” section, and identify the DMX USB PRO,
which usually is “USB Serial Port”

DMX USB Pro Controller MK II LS6970
LS6970 180205
Products and specifications are subject to change without notice 3
www.lumascape.com
User Manual
70314
For latest version visit:
www.enttec.com
3ID: 3647846
Right click on it and select Properties.Under “Port
Settings”, click on “Advanced”, and you can then
change the COM Port No. under this screen:
Setting up on Mac
Download and install PRO-MANAGER on your Mac (OSX
10.6 onwards). The “D2XX” drivers are copied by PRO-
MANAGER and made ready for use.
In some cases, there might be a conflict with other
drivers on your Mac, to resolve such conflicts you will
need to disable “Serial drivers” on your Mac.
Follow detailed instructions on how to do this, using
FAQ/Support links on the PRO Mk2 web-page:
www.enttec.com/promk2
DMX Breakout Cable
Supplied with every PRO Mk2 is a DMX Breakout cable
(pn: 79146). It has a DB15 connector on one end, to
connect to the PRO Mk2, and 3x 5pin DMX connectors
on the other end, to connect to DMX fixtures as needed.
Only ENTTEC branded cables should be used for DMX
or MIDI Breakout, with PRO Mk2.
DMX + MIDI breakout cable (pn: 79147), can be purchased
separately and is needed to allow MIDI input or output.
DMX Out (DMX 1 and DMX 2)
The DMX Out socket(s) should be connected to the
network of DMX512 devices that are to be controlled by
the PRO Mk2. Both ports can be used to output at the
same time (allowing 2 universe of DMX together). Please
refer to the software support to confirm whether it
supports both outputs with PRO Mk2 or not.
It is not necessary to have any connection to the DMX Out
socket while programming the PRO Mk2.
DMX In (DMX 1 and DMX 2)
The DMX In socket(s) should be connected to the DMX512
controller or console whose output is to be captured by
the PRO Mk2. Input is captured and sent to the software
interfacing with the PRO Mk2.
•Although there is only one DMX Input (DMX1)
socket in the breakout cable, the other socket
(DMX2) can also be used as an input by using a
Gender Changer
•Each port can only be used as input or output at
any single time.
•Both ports are isolated and separated, so one can
be used to receive DMX input, and the other to
output DMX, as long as the software supports this
operation.
PRO-MANAGER
ENTTEC provides a free cross-platform app to configure,
test and update PRO Mk2. The app is available for
Windows on the CD or you can download the latest
version for Windows or Mac from the ENTTEC website
www.enttec.com/pro-manager
•Use this App to test your PRO Mk2 - change
default parameters (Refresh rates, Break Time),
test DMX Send and Receive, and setup standalone
mode.
•This App is merely a troubleshooting tool and not
Lighting Control software.
•PRO-Manager runs inside a browser window and
it opens up the page by default, however you can
also use the address: http://localhost:55555/ in
your browser to connect to it.

DMX USB Pro Controller MK II LS6970
LS6970 180205
Products and specifications are subject to change without notice 4
www.lumascape.com
User Manual
70314
For latest version visit:
www.enttec.com
4ID: 3647846
From the PRO-Manager Home page, you can click the
button (Find Devices) to search for PRO Mk2 connected
to your computer. Once it finds it, please select it from
the selection box to talk to it.
Firmware Update
The following steps will guide you on how to update
the firmware. This procedure can also be used to reset
PRO MK2 if it ever gets stuck or stops responding.
(error mode).
•Firstly, download the firmware file meant for
PRO Mk2 (available on the website under
“Firmware” www.enttec.com/promk2)
•Now, upload this file using the upload button
in PRO-Manager (“Choose File” - as per
Chrome browser).
•After selecting the correct file, click on the
“Update Firmware” button and let the update
proceed.
•Firmware update progress is shown in real-
time on the page, please wait till it finishes.
•Once Finished, the page will automatically
refresh, and device information will be
updated to reflect the updated firmware.
DMX Send Test
PRO-Manager can also be used to send preset DMX
patterns or test selected DMX channels by sending DMX
through the PRO Mk2
Select the “DMX Send” page from the top-menu and from
DMX Send page, select “Faders” and drag the needed
Channel faders to test the DMX output.
With your fixtures connected to the DMX output of the PRO
Mk2, you will see the desired effect for the value of the
channel you change. For example, a fixture setup with
intensity on Ch10, and R,G,B on Ch 4,5,6 - when you change
the values on these channels you will see the effect on your
fixtures.
This can be used to test that your PRO Mk2 is working as
expected.
While DMX is being output, the led will blink appropriately
to signify which DMX port is being used to output. For
example, yellow and green led blink means output on both
Ports.
After testing, you must close PRO-Manager, and then open
any lighting control software to use PRO Mk2.
Standalone Mode
Standalone mode allows you to record and playback a DMX
sequence/show using either DMX input or Art-Net onto PRO
Mk2 Memory. The duration of the recording depends on the
Standalone recording options. The recorder is smart enough
to only record the changing frames, so as to accommodate
as many frames as possible.
The PRO Mk2 draws its power from the USB connection.
You can also use a 5v USB Power adaptor (pn: 50327) to
power the PRO Mk2 and use it in standalone mode only.
Recording is done in two steps, and PRO-Manager guides the
user through the process.
Recording Options:
•Show Name: Name to identify the show being recorded
•DMX Channels: no. of channels to record per DMX Frame
(less channels = longer duration of recording)
•Play Count: Total no. of times the show is played back
(from 1 to Forever)
•Loop Delay: Delay in no.of seconds, between each Loop
playback

DMX USB Pro Controller MK II LS6970
LS6970 180205
Products and specifications are subject to change without notice 5
www.lumascape.com
User Manual
70314
For latest version visit:
www.enttec.com
5ID: 3647846
•Play on power-up: If selected as “YES”,
recorded show plays on power-up (this option is
required to be selected for true standalone
operation).
•Output Port: The DMX Port to output the show.
(Only one Port is allowed)
After selecting the options, you can select the input (Art-
Net and universe or DMX) and click on “Record DMX” to
start the recording. The recording is saved onto a file, and
is only transferred to the PRO Mk2 memory when
recording is stopped using the “Stop Recording” button.
Recording Control:
By enabling Recording Control, and selecting the Trigger
Channel and respective value, it will only record whilst
the trigger is active.
Once the selected trigger channel and value is not sent
anymore, the recording will stop automatically.
It will still need to be manually stopped to proceed to
next step of recording.
Step1: Recording DMX to File
In Step1, the DMX is recorded to a binary file, that is saved
in a location shown under the progress window.
Recording begins, only when the first frame is captured,
to get a finer control, “Recording Control” may be used
and a trigger besuitably defined, which controls whento
start the recording.
Recorded frames as counted, are shown and an estimate of
the memory usage is also shown via the progress bar. The
recording will stop automatically, if the entire memory has
been used.
While recording from Art-Net, the DMX is also output on
selected DMX Port and serves as a preview of the recording.
While recording from DMX input, the DMX will not be output
during the recording.
To proceed to the next step and finish the recording process,
click on “Stop recording”.
Step2: Upload File to Device
Once the recording has been stopped, Click on “Write to
Memory” button to begin Step2
During Step2, the show file is loaded on to the memory of
PRO Mk2 and the progress is shown on the page. Once
complete, the page will reload and will allow Standalone
Show control (Start, Stop and Record buttons).
It is important, not to interrupt the memory load process, as
it might corrupt the show if you do so. Please wait till the
upload progress finalises.
Standalone Show Control:
You can also export the recorded show from the PRO Mk2 to
a binary file using “Export Show to File”, and this file can
then be imported back to the PRO Mk2 memory using
“Import Show” button.
Using the Export and import functions, one can make use of
the same standalone shows for multiple PRO MK2 devices.
Show Control on this page can also be used to start or stop
the show as needed.
Please note: any DMX generated by software (on the DMX
port that is meant for standalone mode) will stop playing
the show and output DMX as directed by the software.

DMX USB Pro Controller MK II LS6970
LS6970 180205
Products and specifications are subject to change without notice 6
www.lumascape.com
User Manual
70314
For latest version visit:
www.enttec.com
6ID: 3647846
DMX Connector pin out
5pin DMX OUT/ DMX IN:
•Pin 1: Ground
•Pin 2: Data -
•Pin 3: Data +
•Pin 4: NC
•Pin 5: NC
Any suitable 3 to 5pin DMX adaptor can be used to
connect to 3pin DMX cables or fixtures. Please note the
pinout, before connecting to any non-standard DMX
connector.
MIDI Connector pin-outs
5pin MIDI OUT:
•Pin 1: NC
•Pin 2: Ground
•Pin3: NC
•Pin 4: Data +
•Pin 5: Data -
5pin MIDI IN:
•Pin 1: NC
•Pin 2: NC
•Pin3: NC
•Pin 4: Data +
•Pin 5: Data -
Specifications
Due to continuous improvements and innovations of all
ENTTEC products, specifications and features are subject to
change without notice.
Item
Value
Power
Requirements
500mA supplied by USB
Weight
0.19Kg / 0.42 lbs
Shipped weight
0.35Kg / 0.77 lbs
Length
105mm / 4.1”
Width 66mm / 2.6”
Height
22mm / 0.9”
Op Environment
0°-> 50°
Connectors
1 * 15-Pin breakout Connector
1 * micro USB B Male Connector
Ordering Information
PRO Mk2 and related products can be ordered from our
website or through your ENTTEC dealer using the following
part numbers.
Item
Name
70314 DMX USB PRO Mk2
79147 3DMX + 2MIDI Breakout Cable (0.1m)
70317 PRO Mk2 Zip Case
79149 5W USB Power Supply
79146
3DMX Breakout Cable (0.1m)
70318
PRO2 Wall Mount Kit
70029
3-pin female to 5-pin male adapter
70030
5-pin female to 3-pin male adapter
Registration
Please register your ENTTEC product to get latest software
updates and to validate your warranty. To register, please
visit enttec.com/register