enware IFO SPIRA WC User manual

I00422_Jan 22
enware.com.au
1300 369 273 | [email protected]
Installation and Maintenance Instructions
IFO SPIRA WC
The more
stars the more
water efficient
WATER RATING
www.waterrating.gov.au
3.3litres
average flush
4.4 L per full flush / 3.1 L per half flush
Licence No. 0021
IFO/
AS1172-1
WM-040187

2 Call 1300 369 273 www.enware.com.au
contents
Page
Product Description 3
Contents 4
Installation 5
Floor Mounting Method 7
Installation - Accessories 10
Access to Cistern Internal Components 14
Maintenance 16
Cleaning 17
Troubleshooting 17
Spare Parts 18
Warranty 19

www.enware.com.au Call 1300 369 273 3
Ifo Spira Raised Height S-Trap
IFO6261 CARE620
CARE621
155
105
FRONT VIEW
Bottom
Inlet
1/2” BSP
Male
*
* See WC Set Out
650
355
340
415
470
355
460
900
Pan outlet
250
15
480
to top of seat (Pressalit IFO553/ 554 seat)
CARE6261

4 Call 1300 369 273 www.enware.com.au
Installation shall be in accordance with the AS/NZS3500 series of Standards, the Plumbing Code of
Australia (PCA), and the manufacturer’s instructions.
Installations not complying with AS/NZS 3500, the PCA or the manufacturer’s instructions may void
the product and performance warranty provisions.
Enware Australia advises:1. Due to ongoing Research and Development, specifications may
change without notice; 2. Component specifications may change on some export models.
All measurements are in millimetres.
contents
IFO733
39
Water Supply Inlet Pressure Min. 50 kPa - Max. 500 kPa
Inlet Connection 1/2” BSP
Water Inlet Connection Method Bottom Inlet
Outlet Connection DN100 DWV PVC Pan Collar
Flush Volume 4.4 Full Flush / 3.1L Half Flush (WELS 4 Star)
TECHNICAL INFORMATION
technical data
Rear Cover
Toilet Seat (With Lid)
[OPTIONAL]
Toilet Seat (No Lid)
[OPTIONAL]
Raised Flush Button
[OPTIONAL]
Support Arms
[OPTIONAL]

www.enware.com.au Call 1300 369 273 5
installation
Rear Cover
Toilet Seat (With Lid)
[OPTIONAL]
Toilet Seat (No Lid)
[OPTIONAL]
Raised Flush Button
[OPTIONAL]
Support Arms
[OPTIONAL]
Determine location and set out for the toilet pan.
Set out for S-trap pan for various applications is shown below.
1428.1 Set Out / Disabled
In accordance with AS 1428.1:2021 Performance Based Solution
Institutional / Health Set Out
Set out typical for hospitals which allows for substantial air circulation and free coving
Finished Wall
20
220
150
800 +/-10
460 - 480
Pan outlet
Finished Wall
20
170
100
750
Pan outlet

6 Call 1300 369 273 www.enware.com.au
With no arm support system With arm support system
Minimum Set Out
The minimum to still allow air circulation behind the WC pan
45 ° Corner Set Up
285
MINIMUM
285
MINIMU
M
Finished Wall
Finished Wall
175
MINIMUM
175
MINIMU
M
100
30
Minimum clearance
680
Pan outlet
Finished Wall
20

www.enware.com.au Call 1300 369 273 7
Water Inlet Connection
The water connection to the cistern inlet is a 1/2" BSP male,
bottom inlet.
Looking from the front of the pan, it is located on the right hand
side, on the bottom of cistern.
Install a cistern tap in the vicinity.
155
105
FRONT VIEW
Bottom
Inlet
1/2” BSP
Male
*
* See WC Set Out
650
355
340
415
470
355
460
900
Pan outlet
250
15
480
to top of seat (Pressalit IFO553/ 554 seat)
Floor Mounting Method
Determine floor fixing requirements according to the quality and strength of the floor material,
and the site risk assessment.
If there are no support arms, or there is no possibility of using
support arms in future, use:
• Silicone sealant fixing (Tiled or similar hard floor only. No Vinyl);
• Pan Screw fixing; or
• Bracket fixing (Optional - IFO98016 Bracket sold separately.)
If toilet has support arms or may have support arms in future
(raised height toilet models only), use:
• Pan Screw fixing; or
• Bracket fixing (Optional - IFO98016 Bracket sold separately.)
This installaon informaon is a guide only. Appropriate xing method must be determined by
site-specic risk assessment.

8 Call 1300 369 273 www.enware.com.au
Fixing With Silicone Sealant:
Determine if this method of fixing to the floor would be suitable according to the site risk
assessment. This method of fixing is only suitable for tiled or similar hard floor surfaces. It is
not suitable for vinyl floors, or for toilets with support arms.
IMPORTANT - For Toilets with Support Arms:
Due to the extra force applied to the toilet pan by support arms, the toilet pan must be fixed
to the floor using stainless steel pan screws or a floor fixing bracket.
Fixing the toilet pan with only silicone sealant is not an adequate method of fixing.
Ensure the floor surface and bottom surface of pan
are clean and dry - free of dust, moisture and grease.
Apply silicone sealant to the entire bottom contact
surface of pan and around the perimeter, to achieve
good adhesion and to create a strong bonding
between the pan and the floor.
Install pan into position. Let the silicone sealant dry for
at least 24 hours.
Use white blind cover plugs supplied to plug the screw
holes on the pan.

www.enware.com.au Call 1300 369 273 9
Fixing With Pan Screws:
Determine if using pan screws would be appropriate
according to the quality and strength of the floor material, and
the site risk assessment, taking into account the thickness
of floor surface and mortar bed, the distance to structural
concrete slab, and the impact to waterproofing membrane.
Ensure the pan screws can be fixed onto floor material with
adequate structural integrity and strength. If pan screws
are not long enough or they cannot be fixed onto floor
with adequate strength, use floor mounting bracket with
appropriate fixings. (Floor mounting bracket IFO98016 sold
separately.)
Installing the Pan:
1. Through the pan fixing holes, mark the floor then
pre-drill holes on the floor. The holes should be
drilled at a slight angle and approx. 50mm deep.
2. WC pan should be bedded with silicone sealant.
Ensure the floor surface and bottom surface of
pan are clean and dry, free of dust, moisture and
grease.
3. Apply silicone sealant to the entire bottom contact
surface of pan and around the perimeter to
achieve good adhesion and to create a strong
bonding between the pan and the floor.
4. Install pan into position.
5. Fix the pan in place with pan screws. Hand
tighten the screws, but do not over-tighten. (Over-
tightening screws will cause the ceramic to crack.)
6. Attach white screw caps (supplied) onto the heads
of fixing screws.
30 - 40
98
Base level
of pan
4
Pan Screw
50
60°-65°

10 Call 1300 369 273 www.enware.com.au
Fixing With Floor Mounting Bracket:
(IFO98016 Floor Mounting Bracket sold separately.)
On Concrete Slab / Floor Before Waterproofing:
1. Position the bracket on the floor according to layout
template. (See diagram below, and IFO98016 bracket
installation instructions for more details.)
2. Mark fixing bolt holes for the bracket on floor. (Do not
drill bolt holes through the bracket yet.)
3. Where marked, install 4 threaded rods onto structural
concrete slab or floor. Ensure threaded rods are long
enough so that it protrudes at least 50mm from the
finished floor.
4. Apply waterproofing as normal.
After The Floor is Finished:
5. Once floor is finished, mark 4 bolt holes on bracket,
and pre-drill the marked holes.
6. Fix the bracket onto floor using the threaded rods and
matching washers and nuts.
7. Cut off any excess threaded rod.
1
85
60
80
1
94
1
1
0
Bo
l
t
h
o
l
e
pos
i
t
i
on
s
to
x
b
r
a
cke
t
onto oor
S
-Trap
W
aste Out
l
et
F
oot o
f
pa
n
420 a
pp
rox. to front of
p
a
n
7
0
1
60
Bracket Position

www.enware.com.au Call 1300 369 273 11
4x 12Gx50mm
Screws
(Drill pilot holes
on bracket with
3 mm drill)
Installing the Pan:
8. WC pan should be bedded with silicone sealant.
Ensure the floor surface and bottom surface of
pan are clean and dry, free of dust, moisture and
grease
Apply silicone sealant to the entire bottom
contact surface of pan and around the perimeter
to achieve good adhesion and to create a strong
bonding between the pan and the floor.
9. Install pan into position.
10. Through the pan fixing holes, pre-drill the bracket
using a 3mm drill bit.
11. Fix the pan in place using four 12G x 50mm
screws supplied. Hand tighten the screws, but
do not over-tighten. (Over-tightening screws will
cause the ceramic to crack.)
12. Attach white screw caps (supplied) onto the
heads of fixing screws.

12 Call 1300 369 273 www.enware.com.au
Install Rear Cover
After pan is levelled, water supply and waste are connected, and the pan is tested and
visually inspected for any leaks, install the rear cover to plug the inspection hole.
Apply silicone sealant around the rear cover to create a thorough seal between the rear cover,
pan and floor. Ensure no gap is left that can let any moisture to get through inside the base of
the pan.
Water Inlet Connection
Flush the water supply line to ensure the line is clear,
and connect water supply to the inlet connection of
the cistern.
The inlet connection requires sealing with a washer. If
hard pipe connection with compression nuts or thread
sealing is used, use the loose nut extention fitting
supplied.
The inlet connection is flexible. Hold the inlet thread
on the hex with a spanner when making the thread
connection.
Do not use the toilet until the silicone bed has cured.

www.enware.com.au Call 1300 369 273 13
fresh odour cleaning tablets
This WC is prepared for Fresh WC function,
with a hygienic dosing of a tablet through the
flush button. The tablet is placed inside the
Cover Screw Rod by opening the flush button
and releasing the tablet in the blue Cover Screw
Rod, as illustrated.
The tablet produces a fresh odour and cleaning
effect on the whole bowl and colour.
installation - accessories
Install Toilet Seat and Support Arms (Optional)
Install toilet seat according to toilet seat instructions.
If installing support arms, note that the support arms need to be fixed with the seat at the
same time. Refer to IFO98125 support arms installation instructions for more details.
Raised Flush Button (Optional):
IFO FRESH WC
ONLY
Max. 1
4
CLICK
CLICK
PUSH
OUTWARDS
T
O TAKE OFF
5 CLICK
The raised flush button
can be installed in
place of the standard
flush button.
To take off the flush
button, raise the
button by the hinge,
and push outwards.
To install raised flush
button, fit from the top
and push down to clip
into place.
(Full flush is on the left
hand side.)

14 Call 1300 369 273 www.enware.com.au
access to cistern internal components
The internal components of the cistern can be accessed by first lifting the flush button,
unscrewing the Cover Screw Rod, then unscrewing the cistern fixing screws, and lifting the
ceramic shroud.

www.enware.com.au Call 1300 369 273 15
maintenance
Outlet Valve
To access the outlet valve, twist and lift up
the valve assembly.
Inlet Valve
To access the inlet valve, first lift the
complete cistern up off the pan. Release the
inlet hose from cistern by pulling down and
out. Release the catch of the inlet valve on
cistern, and lift up the inlet valve assembly as
shown.
Flush Volume
The flush volume is fixed at 4.4L for full
flush and 3.1L for half flush. Flush volume
is not adjustable on this product.

16 Call 1300 369 273 www.enware.com.au
Reinstalling Cistern Cover:
To reinstall the cistern cover, follow steps on
page 14 in reverse order.
The screws for the cistern mounting must be
tightened alternately to a maximum torque of
2.5 Nm.
The cover screw should be tightened to a
maximum torque of 1 Nm.

www.enware.com.au Call 1300 369 273 17
cleaning
• WC units have a glazed surface. Glazed surfaces are easy to keep clean and are resistant
against most chemicals.
• Clean bowl regularly.
• Clean external surfaces regularly with a dry, soft cloth. Alternatively clean with hot water
and soap, using soft cloth or a sponge, and wipe dry with a cloth.
• Avoid using cleaning agents on the flush button, instead, use hot water and soap and
wipe dry with a cloth. This is because cleaning agents for porcelain are not intended for
chrome parts/plastics and can risk cracking the flush button if used frequently.
• Cleaning utensils, which contain abrasive agents, such as steelwool and green scouring
pads, must not be used. Strong abrasive materials can scratch the glaze and devoid it of
its original qualities.
• Strong acids such as hydrochloric acid or sulphuric acid, strong alkaline such as caustic
soda, and cleaning powders or pastes must not be used.
• Running WC units should be repaired immediately.
troubleshooting
PROBLEM CAUSE RECTIFICATION
Toilet not flushing away
Drain blockages
Offset pan collars are
used
Do not use offset pan collars
that can impede outlet flow.
Water constantly runs into
bowl
Inlet valve failure Replace inlet valve assembly or
inlet valve seal.
Outlet valve seal washer
is worn or damaged
Replace outlet seal washer.
Water leaks between
cistern and pan
Spreader is dislodged
from cistern or is missing
Take ceramic cistern cover off,
fit spreader back onto cistern,
re-install cistern onto pan.
Water leaks at water inlet
connection to cistern
Inlet connection is not
sealed properly
Use loose nut extension fitting
supplied (IFOS-009) on the inlet
connection.
For further assistance, call Enware on 1300 369 273.

18 Call 1300 369 273 www.enware.com.au
spare parts
Description Sales Code
1Outlet valve seal IFO245V
2Inlet valve arm and seal IFO333V
3Inlet valve assembly IFO333
4Outlet valve assembly IFO245
5Flush button chrome - standard IFO97251
6Flush button chrome - raised IFO97200
7Cover screw rod - blue IFO96763
8Spira cistern ceramic shroud cover IFO90710
9Cistern xing screw and clip - pair IFO98949
10 Spira inner cistern tank only IFO97202
11 Spira cistern gasket foam seal IFO97230
12 Spreader - Spira IFO98512
13
Loosenut Extension 1/2” BSP for
inlet connection
IFOS-009
1
2
3
4
13
Description Sales Code
14 Pan screws x 4, white screw caps
x 4, white blind cover plugs x 4 IFO98381
15 White blind cover plugs x4 IFO94752
16 White screw caps x4 for pan
screws IFO91292
17 Flooor mounting kit IFO98016
18 Ifo S-trap pan back inspection
opening cover -soft IFO733
19 Spira Toilet Bowl S trap IFO90736
20 Replacement Armrest Handle -
Grey (each) IFO96350
Replacement Nurse Call Switch IFO80011
21
Toilet Roll Holder for IFO98125 (each) IFO96348
22
Ifo Cistern Key with Hex and T25 Torx IFO91960
22
15
16
14
20
21
17 18
19
5
6
78
10
11
12
9

www.enware.com.au Call 1300 369 273 19
product warranty for Australia Effective 27 September 2021
Enware Australia Pty Limited (ACN 003 988 314)
(“we” or “us”) warrants that this product (also referred
to as “our goods”) will be free from all defects in
materials and workmanship for 12 months* from the
date of purchase. Our liability under this warranty
is limited at our option to the repair or replacement
of the defective product or part, the cost of repair
of the defective product or part or the supply of an
equivalent product or part, in each case if we are
satisfied the loss or damage was due to a defect in
the materials or workmanship of the product or part.
All products must be installed in accordance with the
manufacturer’s instructions, the Plumbing Code of
Australia (PCA), and AS/NZS3500 including any other
applicable regulatory requirements.
exceptions
This warranty does not apply in respect of any
damage or loss due to or arising from:
a) Failure by you or any other person to follow
any instructions for use (including instructions
and directions relating to the handling, storage,
installation, fitting, connection, adjustment or repair of
the product) published or provided by us;
b) Failure by you or any other person responsible for
the fitting, installation or other work on the product to
follow or conform to applicable laws, standards and
codes (including the AS/NZ 3500 set of Standards,
all applicable State and Territory Plumbing Codes,
the Plumbing Code of Australia and directions and
requirements of local and other statutory authorities);
or
c) Any act or circumstance beyond our control
including faulty installation or connection, accident,
abnormal use, acts of God, damage to buildings,
other structures or infrastructure and loss or damage
during product transit or transportation.
making a claim
To make a claim under this warranty you must
notify us in writing within 7 days of any alleged defect
in the product coming to your attention, provide us
with proof of your purchase of the product and have
completed the Online Product Service and Warranty
Form available on website:
www.enware.com.au/warranty-service-form
All notifications and accompanying forms must be
sent to us marked for the attention of the Enware
Australia Pty Limited, 9 Endeavour Road, Caringbah
NSW 2229. We can also be contacted by telephone
(1300 369 273) or by email ([email protected]).
Your costs in making a claim under this warranty,
including all freight, collection and delivery costs, are
to be borne and paid by you. We also reserve the
right at our cost to inspect any alleged defect in the
product wherever it is located or installed or on our
premises.
* Ifo Toilet - Ceramics: 10 Years warranted against material
and manufacturing defects (parts only) | Flush Valves, WC
seats, Fittings and Accessories - 2 Years warranted against
material and manufacturing defects (parts only) | Pressalit
Toilet Seats (Non Care) - 10 years warranted against
material and manufacturing defects (parts only)
| Accessories & Spare Parts - 2 Years warranted against
material and manufacturing defects (parts only)
For more on warranty, see www.enware.com.au/warranty
other conditions
Except as provided or referred to in this document,
we accept no other or further liability for any
damages or loss (including indirect, consequential
or economic loss) and whether arising in contract,
tort or otherwise. Any benefits available to you under
this warranty are in addition to any non-excludable
rights or remedies you may have under applicable
legislation, including as a “consumer” under the
Australian Consumer Law. To that extent you need to
be aware that: our goods come with guarantees that
cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure
does not amount to a major failure.

ADDRESS: 9 Endeavour Rd Caringbah NSW 2229 Australia
POSTAL ADDRESS: P.O. Box 2545, Taren Point NSW 2229 Australia
1300 369 273 (AUS) WWW.ENWARE.COM.AU [e-mail]
ABN 23 003 988 314