BEMIS bioBidet SLIM ONE User manual

OWNER’S MANUAL
SLIM ONE

3
TABLE OF CONTENTS
PRODUCT INFORMATION
Safety Precautions..................................................4
Parts...............................................................................8
Product.........................................................................9
Dimensions.................................................................10
Remote Control.........................................................11
INSTALLATION
Installation..................................................................12
HOW TO USE
How to Use.................................................................14
Maintenance & Cleaning.....................................22
Settings.......................................................................24
Troubleshooting.....................................................25
Specifications..........................................................26
WARRANTY
Warranty.....................................................................27

4 5
SAFETY PRECAUTIONS
IMPORTANT SAFEGUARDS
•When using electrical products, especially when children are present,
basic safety precautions should always be followed.
READ ALL INSTRUCTIONS BEFORE USING
•For use with 120V 60Hz: Power supply must be a
15 Amp GFCI outlet.
•The electrical cord must be connected to a GFCI outlet.
•The GFCI outlet should be 1 ft. above the floor.
•Install only in well-ventilated areas to avoid excess humidity.
•Do not install in narrow toilet stalls or in shower stalls.
•Install only where direct contact with water is minimized.
•Do not install near any heat source.
•Avoid using extension cords if possible. Consult with a certified electrician
where extension cords are necessary.
DANGER - TO REDUCE THE RISK OF ELECTROCUTION
•Do not use while bathing.
•Do not place or store products where it can fall or be pulled
into a tub or sink.
•Do not place in or drop into water or other liquid,
•Do not reach for a product that has fallen into water.
Unplug immediately.
WARNING - TO REDUCE THE RISK OF BURNS, ELECTROCUTION
OR INJURY TO PERSONS:
•Close supervision is necessary when this product is use
by, on, or near children.
•Use this product only for its intended use as described in this manual.
Only use attachments recommended by the manufacturer.
•Never operate this product if it has a damaged cord or plug, if it
is not working properly, has been dropped or damaged, or dipped into
water. Return the product to a service center for examination and repair.
•Keep the cord away from heated surfaces.
•Never drop or insert any objects into any opening or hose.
•Do not use outdoors or operate where aerosol (spray) products are being
used or where oxygen is being administered.
•Connect this product to a properly ground outlet only.
See grounding instructions.
•Unplug this product before filling. Fill (reservoir) with water only.

6 7
GROUNDING INSTRUCTION
DANGER- Improper use of the grounding plug can result in a risk
of electric shock.
This product has a three-prong grounding plug, which must be plugged into
an outlet that is properly installed and grounded. In the event of an electrical
short circuit, grounding reduces the risk of shock by providing an escape
wire for the electrical current. If repair or replacement of the cord or plug is
necessary do not connect the grounding wire to either flat blade terminal.
The wire with insulation having an outer surface that is green with or without
yellow stripes is the grounding wire. Check with a qualified electrician or
service person if the grounding instructions are not completely understood,
or if in doubt as to whether the product is properly grounded.
This product is for use on a nominal 120V circuit, and has a grounding plug
that looks like the plug illustrated in sketch A in Figure 1.
A temporary adapter, which looks like the adapter illustrated in sketches B
and C, may be used to connect this plug to a 2-pole receptacle as shown in
sketch B if a properly grounded outlet is not available.
The temporary adapter should be used only until a properly grounded outlet
(sketch A) can be installed by a qualified electrician.
The green colored rigid ear, lug, or the like extending from the adapter must
be connected to a permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place by the screw.
OPTIONAL GROUNDING INSTRUCTIONS
SAFETY PRECAUTIONS (CONT.)
GROUNDING

8 9
PARTS
Water supply hose
PRODUCT

10 11
DIMENSIONS REMOTE CONTROL
Elongated type
18.5(470)
15.9(406)
8.1(206)
4.7(120)~8.3(210)
6.8(173)
asas
momo momomomo
BideBide urbourbo
PulsPuls
erer
emem
EnEn gygy
SavingSaving
SeatSeat
emem
NozzleNozzle
CleaningCleaning
ChilChil
erer
essuessu
NozzleNozzle
ositioositio
ONON
BIDETT TTURBO
STOP
PULSE SEAT TEMP
NOZZLE CLEANING
ENERGY SAVING
WATER TEMP
CHILD
+/-
WASH
To run the bidet
function. (1 minute)
To run the turbo
function. (1 minute)
To control the
nozzle position.
To run the pulse function
during wash/bidet/
turbo operation.
Selecting nozzle cleaning while
not seated, the nozzle cleans
itself 3 times.
Then nozzle extends and stop
for manual cleaning process.
Children safety and
automatic mode.
Night light
Press “+” for longer than
3 seconds while not seated.
To control water pressure.
To run the wash function.
(1 minute)
To stop any
operations.

12 13
INSTALLATION
1. Remove the seat from
the existing toilet body.
•Release the nuts, and then
remove the seat and cover.
•Store the seat in a proper
place for future use.
•Turn off the water.
•Remove the existing water
hose and then install T-valve
to the bottom of the toilet
tank. Ensure the rubber
washer is properly seated and
attach the original water hose
to the T-Valve.
2. Install the T-Valve.
3. Fix the catch plate onto
the toilet.
•Point the arrow on the catch
plate towards the toilet tank.
•Push it until you hear a “click”.
•When the product is not
installed well, it may
cause leakage.
•Adjust as needed before
tightening bolts. Do not over
tighten the bolts.
4. Push the main body
toward the catch
plate completely.
AlignAlign
Removal ofRemoval of
water hosewater hose
InstallationInstallation
of T-valveof T-valve
5. Connect bidet hose. 6. Turn on the water
•After installing the T-valve,
connect the supplied bidet
hose from the center of the
T-valve to the bidet.
•Make sure to check for leaks.
7. Plug in!
•Plug in and be sure that the
nozzle comes out and retracts
when powered on.
•Do not plug the power cord
with wet hands. Risk of
electric shock.

14 15
•Be sure to sit on the
seat sensor. If the sensor is
not occupied, all functions
will not operate.
•Skin to seat contact needs to
occur to activate seat.
•Selected function can be used
as described.
•When pressing the selected
function again, the nozzle will
oscillate back and forth to
wash a wider range.
•Press the button once again to
stop oscillate function
•The specialized water
spray in Turbo function
helps relieve constipation.
1. Sit On The Toilet Seat
•When pressing the
Pulse button during the
operation of Wash, Bidet,
and Turbo, water pressure
will repeat high and low for
smooth pulsating wash.
•Pulse function will not
operate during the operation
of Sitz bath.
•See page 17, step 14
•When selecting Child
Function, settings adjust to
low pressure.
•1 min Bidet - 30 sec Bidet
Oscillating - 30 sec
Bidet Pulse.
•It provides extra extended
nozzle position, lower
water pressure, lower seat
temperature, lower
water temperature.
2. Wash, Bidet, Turbo 3. Pulse 4. Child Function
Seat sensor
HOW TO USE

16 17
HOW TO USE (CONT.)
5. Nozzle Position Control 6. Water Pressure Control 7. Stop 8. Seat Temperature Control
•Nozzle position is adjustable
(5 levels).
•Water pressure is adjustable.
(5 levels)
•If the water or screen filters
become blocked, it may
cause low water pressure.
Regularly check the water
and screens filters.
•All operations will stop.
•When pressing the stop
button for 3 seconds, unit will
turn off.
•Press Stop, Wash, Bidet, or
Turbo to turn on.
•Seat temperature is
adjustable. (4 levels)
(Off - Low - Middle - High)
•To reduce the chance of low
temperature burns, the seat
has a safety feature that turns
to low temperature (35°C,
95°F) when seat is occupied
for more than 15 minutes
consecutively.
•If the seat is set lower than
middle level, the seat will
remain at off or low level.

18 19
9. Energy Saving Function 10. Nozzle Cleaning 11. Night Light 12.Automatic Tank Draining
•Eco 1 - This mode will be
activated by pressing the
Energy Saving button until
the yellow LED light turns on.
(Seat and water temperature
will be kept at 32°C)
•Eco 2 - This mode will be
activated by pressing the
Energy Saving button until the
green LED light turns on.
•Eco OFF - Press the Energy
Saving button until LED light
turns off.
•When the unit is occupied,
it adjusts to the present
temperature and is returned
to the saving mode when seat
is unoccupied.
•If the seat and water
temperature are off, they will
remain off.
•When selecting Nozzle
Cleaning while not seated, the
nozzle cleans itself 3 times.
Then nozzle extends and stop
for manual cleaning process.
•Clean the nozzle with a brush
and press the STOP button
after completion of manual
cleaning. Then nozzle cleans
itself for 3 times and retracts.
•NOZZLE CLEANING will
not operate if the seat sensor
is activated.
•Water temperature is
adjustable. (4 levels)
(Off - Low - Middle - High)
•Blue LED night light provides
enough brightness to see the
toilet without turning on the
bathroom light. Night light
can be turned on and off by
pressing + for 3 secs while
not seated.
•Night light setting cannot be
adjusted if seat sensor bypass
feature is activated.
HOW TO USE (CONT.)

20 21
13.Sitz Bath 14.Seat Sensor Bypass 15.Reset 16.Using Inline Carbon Filter
•Wash or Bidet is switched to
Wash Sitz Bath or Bidet Sitz
Bath if Nozzle Cleaning button
is pressed during use.
•Water pressure is switched
to 1st level regardless of
preset water pressure
settings and Sitz Bath
operates for 5 minutes.
•LED of Nozzle Cleaning turns
on during the operation of
Sitz Bath.
•Select the Nozzle Cleaning
again to switch to normal
Wash or Bidet.
•The seat sensor can be
activated and deactivated by
pressing Massage button
for 3 seconds.
•If the seat sensor is
deactivated, the unit works
without occupying the seat
and select features cannot be
controlled. Those features are
Night light, Silent mode, and
Nozzle cleaning.
•Press and hold the Stop
button for 5 seconds.
•After 3 seconds, the
seat will power off.
Keep holding another
2 seconds and the
seat will power back on.
This completes the
factory reset process.
Use of external water filter is
only recommended in areas with
known hard water issues.
If a filter is used, it must be
replaced every 3 months. This
product is designed and intended
for use exclusively with Bio Bidet
DIB water filters.
The purchase or use of any other
water filter is not the responsibility
of BBC Innovation LLC.
As such, any use of non DIB
water filters is prohibited and will
void the warranty for those Bio
Bidet products. Bio Bidet will not
be responsible for any resulting
damages or claims related to the
misuse or distribution of non Bio
Bidet DIB filters.
HOW TO USE (CONT.)

22 23
1. Close the water valve.
2. Disconnect the water supply
hose. Take the screen filter
out and clean it with a
soft brush.
3. Return the filter after cleaning
and reconnect the water
supply hose.
4. Open the water valve.
1. Exterior surface of unit is
made of plastic material,
which may be damaged by
scrubber, chemicals, etc.
2. Wipe the surface with a
soft damp cloth. Do not
spray water directly onto
the surface.
3. Clean the body after
removing the power plug
from the outlet. Be sure
no water splashes into the
power plug or outlet.
4. Be careful of not dropping any
chemical detergents or toilet
cleaner on the main body or
supply hose to avoid damage.
1. Remove the power plug from
the outlet.
2. Close the water feed valve.
3. Press the release button and
gently pull to remove the unit
from the catch plate.
4. Use a flat-head screwdriver to
open the drain plug.
•When bidet seat is not
used for an extended
period of time, unplug
and drain the unit.
MAINTENANCE & CLEANING
Screen Filter Cleaning Extended Non-Use Cleaning the Unit Draining of Remaining Water
Water supply hose
Screen filter

24 25
TROUBLESHOOTING
PLEASE CHECK THE FOLLOWING POINTS BEFORE
REQUESTING REPAIR SERVICE.
Self-Diagnosis Table
Please refer to the following table and inform the exact status when
requesting repair service.
PROBLEM CHECK LIST
Completely out of order •Check if the power plug is not connected
•Check if the power supply or outlet
has failed
Water does not spray out •Check if the water supply is turned on
•Check if water valve is open
•Check if nozzle is blocked by
foreign material
•Check if connection hose is bent
Water pressure is low •Check if screen filter is blocked and
clean if needed.
•Check if the water pressure is set at
too low level.
Water is not
warm enough
•Check if its temperature is set at off or low
level, or economy mode
Seat is not warm enough •Check if its temperature is set at off or low
level, or economy mode
No.Self Diagnosis Indication
1Water temp sensor is
disconnected or not inserted.
LEDs of water low + middle
level blinking
2Water temp sensor is
short-circuited or overheated
LEDs of water high + middle
level blinking
3Seat temp sensor is
disconnected or not inserted
LEDs of water low level blinking
4Seat temp sensor is
short-circuited or overheated
LEDs of water high level blinking
SETTINGS
•The unit will work without sitting on the seat if the occupied seat sensor
is deactivated. (Turned off)
•If the seat sensor is deactivated, some features cannot be controlled.
(Night light on/off, silent mode on/off, and nozzle cleaning)
USER SETTING WITH THE REMOTE CONTROL
No. Function Seat
Status
Switch
Operation
Description Initial
Status
1Silent
mode
“ ” For
longer than 3
seconds
To turn on/off the
operating chime
sound.
ON
2Power off “ ” For
longer than 3
seconds
Press one of Stop,
Wash, Bidet, Intensive
or Dry
to power on
3Seat sensor
bypass
“ ” For
longer than 3
seconds
Seat sensor feature
will
be deactivated
OFF
4Night light “ ” For
longer than 3
seconds
To turn on/off the
night light
ON
5Factory
reset
Press and
hold the Stop
button for
5 seconds
After 3 seconds, the
seat will power off.
Keep holding
another 2 seconds and
the seat will power
back on.
This completes the
factory reset process
ON
Seat sensor ‘off’ Seat sensor ‘on’ Regardless of on/off

26 27
WARRANTY
1 YEAR WARRANTY
Bio Bidet warrants its products to be free from manufacturing defects under
normal use and service for a period of 1 year from the date of purchase. This
warranty is extended only to the original purchaser.
For full warranty details, visit www.biobidet.com
Contact Bio Bidet customer support with any questions you may have.
847.458.2334
[email protected]
www.biobidet.com
SPECIFICATIONS
ITEM BIO BIDET SLIM ONE
Rated voltage 120V, 60Hz
Max. Power consumption 870W
Power cord length 1.2 m
Water feed method Directly connects to water pipe
Recommended inlet
water pressure 99~106.6 psi
Wash Feed
Volume Wash 0.13~0.21 gal/min
Bidet 0.13~0.18 gal/min
Turbo 0.13~0.18 gal/min
Child 0.13-0.16 gal/min
Pressure control 5 levels
Temperature control 4 levels (off-low-middle-high)
Heater capacity 800W
Safety device Water level sensor, Thermal fuse,
Bi-metal, Temperature sensor
Heated
Seat Temperature control 4 levels (off-low-middle-high)
Heater capacity 55W
Safety device Thermal fuse
Feed water temp.
tolerance range 37~95°F (recommended 54~95°F)
Usage room temp.
tolerance range 37~104°F (recommended 54~95°F)
Dimension Elongated 18.5”(470) x 20.8”(528) x 6.8”(173)
Weight Net
Weight
(Gross
weight)
Elongated 10.4 lb (15.2)

Thank You
Technical Support/Customer Service
7900 S Route 31 Crystal Lake, IL 60014
T: 845.458.2334
U.S TOLL FREE: 877.339.5214
[email protected]om
www.biobidet.com