Epson S020122 Operating and maintenance instructions

EPSON
MSDS # S020122 Version 3.54 (USA)
Page 1 of 4 Release Date 04/2010
Material Safety Data Sheet
1. Article and Corporate Identification
Product: Epson Ink Cartridge S020122
for use with Epson Stylus Color 3000
and Pro 5000 Printer
Manufacturer/Distributor: Epson America, Inc.
3840 Kilroy Airport Way
Long Beach, CA 90806
United States
TEL: [phone]
FAX: [phone]
The EPSON S020122 Ink Cartridge
2. Composition Information
This is an aqueous ink formulation
Ink Composition CAS No. % By Weight
Proprietary dyes and pigments - < 3 %
Diethylene glycol 111-46-6 <12%
Proprietary organic materials - 10 –15 %
Glycerols - 5 –10%
Water 7732-18-5 balance
3. Hazard Identification
3.1 Emergency Overview: Ink component is a light yellow liquid that may cause eye irritation. Avoid contact with
eyes or clothing. In the case of skin contact, wash with soap and water. Keep out of reach
of children.
3.2 Potential Health Effects:
Eyes: Ink contact with eye may be mildly irritating. See Section 11 for Toxicology.
Skin: Ink contact with skin may cause irritation, swelling, or redness. It is not expected to cause an allergic
skin reaction. See Section 11 for Toxicology.
Inhalation: Intentional exposure to ink vapors may cause respiratory irritation. See Section 11 for Toxicology.

EPSON
MSDS # S020122 Version 3.54 (USA)
Page 2 of 4 Release Date 04/2010
Ingestion: May cause upset stomach. See Section 11 for Toxicology.
4. First Aid Measures
4.1 Eyes: Immediately flush with room temperature, low pressure, clean water for at least 15 minutes.Seek
medical attention if eye irritation continues.
4.2 Skin: Wash surface areas with soap and water. Wash soiled clothing before rewearing. Consult a physician
if irritation continues.
4.3 Inhalation: Remove subject to ventilated fresh air. Consult physician if necessary.
4.4 Ingestion: Seek medical advise; and attention if stomach continues to be upset.
5. Fire Fighting Measures
5.1 Flammability: Flash point is greater than 230 deg. F / 110 deg. C (closed cup in accordance with
ASTM D3278)
5.2 Extinguishing Media: Dry chemical or carbon dioxide
5.3 Fire Fighting Instructions: No special fire fighting procedures are required other than breathing apparatus. No
special explosion hazards are known.
6. Accidental Release Measures
If a spill occurs, use sponges to wipe-up ink, then rinse area with damp cloth. Place waste in closed container for
disposal. Use proper ventilation. Do not dispose of waste to the sewer. No eye or skin protection required during
clean-up. Wash hands with soap and water.
7. Precautions for Safe Handling and Use
Keep out of reach of children and do not drink ink. Do not store the cartridge in high or freezing temperatures. Keep
cartridge out of direct sunlight. Do not dismantle cartridge. Do not store cartridges with oxidizing agents or
explosives. Make sure cartridge is dry before insertion into printer housing.
8. Exposure Controls and Personal Protection
8.1 Engineering Controls: None required
8.2 Exposure Controls: None required
8.3 Personal Protection: None required when cartridges are used as intended
9. Physical and Chemical Properties of Ink Formulation

EPSON
MSDS # S020122 Version 3.54 (USA)
Page 3 of 4 Release Date 04/2010
Appearance: Yellow Liquid
Odor: None
pH: 9 - 10
Boiling point: Approximately 212 deg. F / 100 deg. C
Freezing point: Less than 32 deg. F / 0 deg. C
Melting point: Less than 32 deg. F / 0 deg. C
Flash point: Greater than 230 deg. F / 110 deg. C (closed cup, ASTM D3278)
Autoflammability: None
Explosive properties: None
Oxidizing properties: None
Vapor density: Greater than 1 (air = 1)
Relative density: 1.07 at 68 deg. F / 20 deg. C
Solubility in water: Complete
Solubility in fat: No data available
Partition coefficient: No data available
Viscosity: Less than 5 mPa-s
10. Stability and Reactivity
Stability: Stable
Hazardous polymerization: Will not occur
Hazardous decomposition products: None
Incompatible materials: Oxidizers and explosives
11. Toxicology and Health Hazards
Routes Of Overexposure: Eye, skin, inhalation, and oral
Acute Health Hazards:
•Overexposure of eye surface to ink may be mildly irritating
•Overexposure of skin to ink contact may cause irritation and in some people swelling and redness
•Intentional inhalation overexposure to ink vapors may result in respiratory tract irritation
•Intentional or accidental oral ingestion may cause an upset stomach
Chronic Health Hazards: None known
Carcinogenicity: None Known
Toxicity Data: Oral LD50 Dermal LD50 Inhalant LC50 OSHA Regulated?
> 5000mg/kg(Rats) >2000mg/kg(Rats) Not Applicable Not Established
12. Ecological Information
No data available on the adverse effects of this material on the environment
13. Disposal Considerations
Used and unused cartridges are not a federal RCRA hazardous waste. Disposal should be in accordance with federal,
state, and local requirements.

EPSON
MSDS # S020122 Version 3.54 (USA)
Page 4 of 4 Release Date 04/2010
14. Transportation Information
Not regulated as a Hazardous Material by DOT, IMO, or IATA.
This material does not require a TSCA Section 12(b) Export Notification.
15. Regulatory Considerations
U.S. DOT Hazard Class Regulated? NO
U.S. OSHA Inhalation Hazard? NO
In U.S., NFPA/HMIS Hazard Rating: Health (1), Flammability (1), Instability/Reactivity (0), Other (0)
16. Other Information
This MSDS adheres to U.S. regulatory requirements and standards and may not meet the regulatory requirements in other
locations.
This is a revised Material Safety Data Sheet which replaces all prior U.S. MSDS for this product.
This “Material Safety Data Sheet” contains health, safety, and environmental information. It does not replace any precautionary
language or use and disposal information which accompanies the product. The information contained herein is believed to be
accurate at the time of preparation, but should only be used as a guide. Epson does not warrant the completeness or accuracy of the
information contained herein. It is subject to revision from time to time.
YOU’VE GOT TO SEE IT IN EPSON COLOR ™