Epson Et-16650u User manual

Start Here

10 Press the power button to turn on the product.

Note: If an error message appears, turn off the product and

check that no protective material has been left inside the product

and that the transportation lock is in the printing position.

11 Select your language, country, date, and time.

Note: You can change these settings later using the product’s

control panel. For more information, see the online User’s Guide.

Follow steps 12 and 13 to continue ink charging.

12 When the message to see the Start Here sheet appears

on the LCD screen, press and hold OK for 5 seconds.

13 When the ink conﬁrmation message appears on the LCD

screen, select Done to start charging the ink. Ink charging

takes approximately 9 minutes. A message appears when

ink charging is complete. Press OK to proceed with initial

setup.

Caution: Do not unplug or turn off the product, raise the

scanner unit, or load paper while the product is charging or you’ll

waste ink.

Note: Part of the ink from the included bottles is used for printer

setup. You will notice ink levels in the tanks decrease during

charging. This decrease is normal and does not affect the stated

in-box yields.

3Load paper

See the online User’s Guide for information about loading

capacity, available paper types and sizes, loading envelopes,

and using the rear paper feed slot or Automatic Document

Feeder (ADF).

1 Make sure the

product is not

charging ink, then

pull out one of the

paper cassettes.

2 Slide the side edge guides

all the way out and set the front

edge guide to the paper size you

are using.

IMPORTANT: Before using this product, make sure you read

these instructions and the safety instructions in the online User’s

Guide.

Important Safety Instructions: When using telephone equipment, you

should always follow basic safety precautions to reduce the risk of fire,

electric shock, and personal injury, including the following:

• Do not use the Epson®product near water.

• Always keep this guide handy.

• Avoid using a telephone during an electrical storm. There may be a

remote risk of electric shock from lightning.

• Do not use a telephone to report a gas leak in the vicinity of the leak.

Caution: To reduce the risk of fire, use only a No. 26 AWG or larger

telecommunication line cord.

Note: As part of the ReadyPrint™ program, Epson monitors ink usage

remotely to provide you with additional ink before you run out of it. The

product must be connected to the Internet to function and monitor ink

usage.

1Unpack

Note: Do not open the ink bottles until you are ready to ﬁll the ink

tanks. The ink bottles are vacuum packed to maintain reliability.

1 Remove all protective materials from the product.

2 Lift up the scanner unit. Remove all protective materials

from inside the product.

Caution: Do not touch the ﬂat white cable or the ink tubes and

their translucent cover. Do not move the transportation lock from

the printing position.

3 Lower the scanner unit.

2Fill ink tanks

Warning: Keep the ink bottles out of the reach of children and do not

drink the ink.

Caution: This product requires careful handling of ink. If ink spills,

wipe it off immediately with a damp towel to avoid permanent stains.

If ink gets on your clothes or belongings, it may not come off.

Note:

• Use only Epson 582 ink provided to you under the ReadyPrint

program.

• Use the ink bottles included with the printer to set up the product.

• The included ink bottles are designed for reliable printer setup and

cannot be resold.

1 Open the ink tank cover, then open the cap for the

black ink tank.

Note: Refer to the color-coded sticker on the ink tank unit to

identify the color of each tank.

2 Unpack the black (BK) ink bottle. Hold the ink bottle

upright and slowly turn the bottle cap to remove it.

Caution: Do not shake or squeeze the ink bottle. Do not touch

the top of the ink bottle after its cap is removed.

3 Insert the ink bottle into the ﬁlling port.

Note: Do not force the bottle into position; each bottle is keyed

for each color.

4 Wait for the ink to ﬁll the tank. Do not squeeze the bottle.

Note: If ink does not ﬂow from the bottle, lift and reinsert the

bottle.

5 When the ink bottle is empty, remove the ink

bottle and replace the bottle cap.

Note: Do not leave the ink bottle inserted;

otherwise the bottle may be damaged or ink

may leak.

6 Securely close the black ink tank cap.

7 Repeat the previous steps for the other colors.

8 Close the ink tank cover.

9 Connect the power cord to the back of the product and to

an electrical outlet.

Caution: Do not connect to your computer yet.

ET-16650U

Start Here

10 Press the power button to turn on the product.

Note: If an error message appears, turn off the product and

check that no protective material has been left inside the product

and that the transportation lock is in the printing position.

11 Select your language, country, date, and time.

Note: You can change these settings later using the product’s

control panel. For more information, see the online User’s Guide.

Follow steps 12 and 13 to continue ink charging.

12 When the message to see the Start Here sheet appears

on the LCD screen, press and hold OK for 5 seconds.

13 When the ink conﬁrmation message appears on the LCD

screen, select Done to start charging the ink. Ink charging

takes approximately 9 minutes. A message appears when

ink charging is complete. Press OK to proceed with initial

setup.

Caution: Do not unplug or turn off the product, raise the

scanner unit, or load paper while the product is charging or you’ll

waste ink.

Note: Part of the ink from the included bottles is used for printer

setup. You will notice ink levels in the tanks decrease during

charging. This decrease is normal and does not affect the stated

in-box yields.

3Load paper

See the online User’s Guide for information about loading

capacity, available paper types and sizes, loading envelopes,

and using the rear paper feed slot or Automatic Document

Feeder (ADF).

1 Make sure the

product is not

charging ink, then

pull out one of the

paper cassettes.

2 Slide the side edge guides

all the way out and set the front

edge guide to the paper size you

are using.

IMPORTANT: Before using this product, make sure you read

these instructions and the safety instructions in the online User’s

Guide.

Important Safety Instructions: When using telephone equipment, you

should always follow basic safety precautions to reduce the risk of fire,

electric shock, and personal injury, including the following:

• Do not use the Epson®product near water.

• Always keep this guide handy.

• Avoid using a telephone during an electrical storm. There may be a

remote risk of electric shock from lightning.

• Do not use a telephone to report a gas leak in the vicinity of the leak.

Caution: To reduce the risk of fire, use only a No. 26 AWG or larger

telecommunication line cord.

Note: As part of the ReadyPrint™ program, Epson monitors ink usage

remotely to provide you with additional ink before you run out of it. The

product must be connected to the Internet to function and monitor ink

usage.

1Unpack

Note: Do not open the ink bottles until you are ready to ﬁll the ink

tanks. The ink bottles are vacuum packed to maintain reliability.

1 Remove all protective materials from the product.

2 Lift up the scanner unit. Remove all protective materials

from inside the product.

Caution: Do not touch the ﬂat white cable or the ink tubes and

their translucent cover. Do not move the transportation lock from

the printing position.

3 Lower the scanner unit.

2Fill ink tanks

Warning: Keep the ink bottles out of the reach of children and do not

drink the ink.

Caution: This product requires careful handling of ink. If ink spills,

wipe it off immediately with a damp towel to avoid permanent stains.

If ink gets on your clothes or belongings, it may not come off.

Note:

• Use only Epson 582 ink provided to you under the ReadyPrint

program.

• Use the ink bottles included with the printer to set up the product.

• The included ink bottles are designed for reliable printer setup and

cannot be resold.

1 Open the ink tank cover, then open the cap for the

black ink tank.

Note: Refer to the color-coded sticker on the ink tank unit to

identify the color of each tank.

2 Unpack the black (BK) ink bottle. Hold the ink bottle

upright and slowly turn the bottle cap to remove it.

Caution: Do not shake or squeeze the ink bottle. Do not touch

the top of the ink bottle after its cap is removed.

3 Insert the ink bottle into the ﬁlling port.

Note: Do not force the bottle into position; each bottle is keyed

for each color.

4 Wait for the ink to ﬁll the tank. Do not squeeze the bottle.

Note: If ink does not ﬂow from the bottle, lift and reinsert the

bottle.

5 When the ink bottle is empty, remove the ink

bottle and replace the bottle cap.

Note: Do not leave the ink bottle inserted;

otherwise the bottle may be damaged or ink

may leak.

6 Securely close the black ink tank cap.

7 Repeat the previous steps for the other colors.

8 Close the ink tank cover.

9 Connect the power cord to the back of the product and to

an electrical outlet.

Caution: Do not connect to your computer yet.

ET-16650U

3 Follow the instructions on the computer screen to run

the setup program.

4 When you see the Select Your Connection screen, select

one of the following:

• Wireless connection

In most cases, the software installer automatically

attempts to set up your wireless connection. If setup

is unsuccessful, you may need to enter your network

name (SSID) and password.

• Direct USB connection

Make sure you have a USB cable (not included).

• Wired network connection

Make sure you have an Ethernet cable (not included).

Mobile and voice-activated

printing

• Print directly from your Android™ (v4.4 or later) device*.

Simply connect your printer and device to the same

network and tap the menu icon to select the print option.

• Turn your mobile device into an intuitive, easy-to-use

printing and scanning control center with Epson Smart

Panel®. Download the app from your mobile device’s app

store.

• Print from wherever you are, next to your printer or

remotely, with Epson Connect™. Learn more at

http://epson.com/connect.

• Use voice-activated assistants to print a variety of creative

and everyday items from your Epson product. Simply add

your product to an Epson Connect account, then link the

account to a voice-activated assistant. See

http://epson.com/voice.

* May require the Epson Print Enabler or Mopria®Print Service app from

Google Play™.

Any problems?

Network setup was unsuccessful.

• Make sure you select the right network name (SSID).

• Restart your router (turn it off and then on), then try to

connect to it again.

• If you see a ﬁrewall alert message, click Unblock or Allow

to let setup continue.

• If your network has security enabled, make sure you enter

your network password (WEP key or WPA passphrase)

correctly. Be sure to enter your password in the correct

case.

• Print a network connection report to identify network

problems and solutions. See your online User’s Guide for

instructions.

There are lines or incorrect colors in my printouts.

Run a nozzle check to see if there are any gaps in the

printout. Then clean the print head, if necessary. See the

online User’s Guide for more information.

EPSON and Epson Smart Panel are registered trademarks, the EPSON logo is a registered

logomark, and Epson Connect is a trademark of Seiko Epson Corporation.

Designed for Excellence and ReadyPrint are trademarks of Epson America, Inc.

Mac is a trademark of Apple Inc., registered in the U.S. and other countries.

Android, Chromebook, and Google Play are trademarks of Google LLC.

Windows is a registered trademark of the Microsoft group of companies.

Mopria®is a registered and/or unregistered trademark and service mark of Mopria Alliance, Inc.

in the United States and other countries. Unauthorized use is strictly prohibited.

General Notice: Other product names used herein are for identiﬁcation purposes only and may

be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

Printed in XXXXXX CPD-63608

3 Insert paper with the glossy or printable side facedown.

Note: Make sure the paper is loaded against the front edge

guide and not sticking out from the end of the cassette.

4 Slide the side edge

guides against the

paper, but not too

tightly.

Note: Make sure the

paper is under the

arrow mark on the

edge guide.

5 Keep the cassette

ﬂat as you insert it all

the way.

6 Select the paper settings on the product’s control panel.

4Connect the fax line

1 Connect a phone cord to a telephone wall jack and to the

LINE port on your product. See the online User’s Guide

for more information.

2 Select Proceed on the LCD screen to set up the fax, or

select Set Up Later to set it up later.

5Install software

Note:

• An Internet connection is required to obtain the product software.

• To print from a Chromebook™, go to

http://epson.com/support/chromebookprint.

1 Make sure the product is NOT CONNECTED to your

computer.

Windows®:If you see a Found New Hardware screen, click

Cancel and disconnect the USB cable.

2 Download and run your product’s software package:

http://epson.com/support/et16650u

The product’s screen is dark.

Make sure your product is turned on, and touch the screen

to wake it from sleep mode.

Setup is unable to find my product after connecting it

with a USB cable.

Make sure your product is on and securely connected.

Any questions?

User’s Guide

Windows: Click the icon on your desktop or Apps screen to

access the online User’s Guide.

Mac: Click the icon in Applications/Epson Software/Guide to

access the online User’s Guide.

If you don’t have a User’s Guide icon, go to the Epson website,

as described below.

ReadyPrint Subscription Technical Support

VIsit http://epson.com/support/et16650u to download

drivers, view videos and manuals, get FAQs, or contact Epson.

Call 800-879-3776, 7 a.m. to 4 p.m. Paciﬁc Time, Monday

through Friday. Days and hours of support are subject to

change without notice.

Recycling

Epson offers a recycling program for end of life hardware

and ink bottles. Please go to http://epson.com/recycle for

information on how to return your products for proper disposal.

Need paper?

Ensure brilliant results with Epson specialty

and plain papers, engineered speciﬁcally for

Epson printers. Find Epson papers at

http://epson.com and at Epson authorized

resellers. Call 800-GO-EPSON (800-463-7766).

Supplier’s Declaration of

Conformity

According to 47CFR, Part 2 and 15 for Class B Personal

Computers and Peripherals; and/or CPU Boards and Power

Supplies used with Class B Personal Computers:

We: Epson America, Inc.

Located at: 3131 Katella Ave.

Los Alamitos, CA 90720

Telephone: (562) 981-3840

Declare under sole responsibility that the product identiﬁed

herein, complies with 47CFR Part 2 and 15 of the FCC rules as

a Class B digital device. Each product marketed, is identical

to the representative unit tested and found to be compliant

with the standards. Records maintained continue to reﬂect the

equipment being produced can be expected to be within the

variation accepted, due to quantity production and testing on

a statistical basis as required by 47CFR § 2.906. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Trade Name: Epson

Type of Product: Multifunction printer

Model: C753C