Epson Disc producer PP-100N Security Service manual

Administrator’s Guide
M00012700

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written
permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information
contained herein. While every precaution has been taken in the preparation of this manual, Seiko Epson Corporation
assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse
of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U. S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or
any consumable products other than those designated as Original EPSON Products or EPSON Approved Products
by Seiko Epson Corporation.
NOTICE: The contents of this manual are subject to change without notice.
Copyright © 2009 Seiko Epson Corporation. All rights reserved.
Trademarks
•Microsoft, Windows, Windows Vista and Internet Explorer are registered trademarks of Microsoft Corporation in the
United States and other countries.
•EPSON is a registered trademark of Seiko Epson Corporation.
Other product names are trademarks or registered trademarks of their respective owners.
Marks used in this guide
The following marks are used in this guide to indicate important information.
Screens appearing in this guide
Unless otherwise indicated, the Windows screens appearing in this guide are Vista screens.
Indicates information with which you must comply when using this product. Ignoring this
information and mishandling the product may cause it to fail or malfunction.
Indicates an additional explanation or information we want you to know.
Note
s

3
Organization of this manual
The following instruction guides are included with this product.
PP-100N Setup Guide Briefly describes how to set up this product using Standard Mode, External
Output Mode and Batch Mode in 25 languages with illustrations. See the
PP-100N Administrator’s Guide for more information.
PP-100N User’s Guide (PDF) Presents detailed information users need to know when using this product
in Standard Mode, External Output Mode, and Batch Mode, such as how
to install the software, the product functions and operations, as well as
maintenance information. It is included on the PP-100/PP-100N Utility &
Documents disc.
PP-100N Administrator’s
Guide (PDF)
Presents detailed information necessary for setting up, operating, and
managing this product when using it in Standard Mode, External Output
Mode, and Batch Mode. It also describes how to troubleshoot various
problems. It is included on the PP-100/PP-100N Utility & Documents disc.
PP-100N Security Setup
Guide
Briefly describes how to set up this product using PIN Controlled Mode and
Security Mode in 25 languages with illustrations. See the PP-100N Security
Administrator’s Guide for more information.
PP-100N Security User’s
Guide (PDF)
Presents detailed information users need to know when using this product
in PIN Controlled Mode and Security Mode, such as how to install the
software, the product functions and operations, as well as maintenance
information. It is included on the PP-100N Security-Documents disc.
PP-100N Security
Administrator’s Guide (PDF)
Presents detailed information that administrators need to know about
setting up, operating and managing this product when using it in PIN
Controlled Mode and Security Mode. It also describes how to
troubleshoot various problems.

4
Table of Contents
Trademarks..................................................................2
Marks used in this guide...........................................2
Screens appearing in this guide ...............................2
Organization of this manual.....................................3
■Table of Contents ...............................................4
Before Using This Product .........6
■For safe use .........................................................6
Cautions for the power source .................................8
Cautions for using......................................................9
WARNING ................................................................ 11
FCC compliance statement for American
users ........................................................................... 11
For Canadian users .................................................. 11
For California customers only ................................ 11
■Cautions for CD/DVD discs..........................12
■Uses of this product.........................................12
■Incidental loss arising from the use of this
product..............................................................12
■Restriction of Use.............................................12
■About open source software licenses............12
PIN Controlled Mode and
Security Mode.........................13
Publish Mode............................................................13
Security control mechanisms..................................15
System configuration...............................................15
■Secure disc creation .........................................16
Roles of the person in charge and the users
(administrators, approvers, publishers)................16
What is a secure disc creation environment? .......17
Preparation..............................18
■Installation ........................................................18
Installation location requirements .........................19
Installation space......................................................19
■Setup procedure...............................................20
■Connecting the authentication keypad ........21
■Connecting the Ethernet cable.......................25
■Connecting the power cord ...........................25
■Installing the ink cartridges ...........................26
■Setting the security lock switch.....................30
■Setting the Publish Mode ...............................31
Types of Publish Modes...........................................31
Installing the stackers ..............................................32
Setting procedure .....................................................34
■Network settings .............................................36
■Registering an administrator .........................42
■System settings ................................................47
Output device settings.............................................47
Notification email transmission settings...............50
Setting the date and time.........................................54
■Installing digital certificates...........................56
Creating a CA certificate and server certificate ...57
Downloading the CA certificate.............................59
Downloading the server certificate........................60
Uploading the server certificate .............................61
■Setting the language........................................62
Administration and
Management ..........................63
■Closing and opening the disc cover..............63
Unlocking the disc cover .........................................63
Opening the disc cover ............................................65
Closing the disc cover..............................................66
■Loading discs ...................................................67
■Managing jobs..................................................68
Checking job information........................................68
Canceling job applications (Security Mode only)
.....................................................................................70
Checking the job processing status........................72
Pausing jobs...............................................................73
Resuming jobs ...........................................................74
Canceling jobs ...........................................................75
Deleting jobs..............................................................76
■Managing users ...............................................78
Checking user information .....................................78
Registering users ......................................................79
Batch registering users.............................................82

5
Changing user information.....................................85
Deleting user information.......................................87
Changing password and PIN .................................89
Unlocking the user account ....................................92
■Managing inspection logs.............................. 94
Checking inspection logs ........................................94
Downloading inspection logs.................................96
■Changing the Publish Mode.......................... 97
Mode change II.........................................................98
Mode change III......................................................100
Mode change IV......................................................102
Maintaining Your Product.....104
■Backing up and restoring data ....................104
Backing up data......................................................104
Restoring data.........................................................106
■Restoring to initial state ...............................107
■Checking maintenance information ............111
Checking device information ............................... 111
Downloading operation log.................................. 113
■Checking the TOE version (Security Mode
only) ................................................................ 114
■Starting Service Mode .................................. 115
■Precautions for transporting your
product ........................................................... 117
Troubleshooting.....................119
■Error messages and remedies...................... 119
■Problems and their remedies....................... 126
Power/Control Panel problems...........................126
Disc writing problems ...........................................127
Label printing problems........................................128
Password/PIN problems ......................................130
Other problems.......................................................131
■Checking with EPSON Total Disc
Monitor........................................................... 133
■When discs cannot be published ................ 135
■Disc does not come out ................................ 138
Drive tray does not come out ...............................138
Printer tray does not come out.............................139
■Disc recording surface is stained with
ink.................................................................... 143
Appendix.............................. 147
■Where to get help.......................................... 147
Before contacting Epson ........................................147
Help for users in the United States and
Canada .....................................................................147
Help for users in Europe (EMEA)........................147
■Product specifications .................................. 148
Basic specifications.................................................148
■Ink and Disc................................................... 153
Ink cartridges ..........................................................153
Discs .........................................................................153

6
Before Using This Product
For safe use
•To use this product safely, be sure to read this guide as well as the other instruction guides included with this
product before using it.
•Keep this guide at hand so that you can resolve any questions you have about this product.
To prevent harm to customers and other people or damage to property, this guide contains the following symbols and
warning displays for operations and use that may be dangerous. Please read the guide after thoroughly
understanding this information.
Install this product in the following type of place.
WARNING
If this display is ignored and the product is mishandled, it may result in death or serious
injury.
CAUTION
If this display is ignored and the product is mishandled, it may result in bodily harm or
physical damage.
Indicates action that should not
be performed (prohibited).
Indicates that the product must
not come in contact with water.
Indicates that disassembly is
prohibited.
Indicates that the plug should be
disconnected from the outlet.
Indicates that contacting the
product with wet hands is
prohibited.
Place that is flat and stable Place with the following temperature and
humidity range
•When using this product in a place where static electricity is easily generated, use an
antistatic mat or other product to prevent static electricity.
•Do not install on a surface that is smaller than the base of the product.
If the rubber bases on the bottom of the product extend beyond this surface, it places stress
on the internal mechanisms, which negatively affects disc writing, printing and transporting.
Be sure to install on a flat surface that is wider than the product so that all of the feet on the
base of the product rest firmly on it.
Flat

7
Before Using This Product
WARNING
•Do not use flammable gas sprays inside or around this product. There is a
risk that gas will build up and a spark may cause a fire.
•Do not install in a place where volatile substances, such as alcohol or paint
thinner, are present or in a place where there is fire.
This may result in electric shock or fire.
CAUTION
Place the product on a flat, stable surface that extends beyond the base of the
product in all directions. If you place the product by the wall, leave more than
10 cm between the back of the product and the wall. The product will not
operate properly if it is tilted at an angle.
Do not install or store in an unstable place (such as on a wobbly or tilted
surface), in reach of children, or in a place subject to vibration from other
machines.
There is a risk that it could drop or fall over, resulting in injury.
Do not install in places where there is excessive moisture or dust, risk of getting
wet, direct sunlight, severe changes in temperature and humidity, or close to
heating and cooling devices.
There is a risk of electric shock, fire, and malfunction or failure of this product.
Do not block the air vents on this product.
Blocking the air vents may result in internal heat build-up and fire.
Do not install in the following types of places.
•Tight spaces where ventilation is poor, such as in a closet or on a bookshelf
•On a rug or bed
If you place the product by the wall, leave more than 10 cm between the
back of the product and the wall. It is also necessary to leave enough space
in front of the product to open and close the disc cover.

8
Cautions for the power source
WARNING
Do not connect or disconnect the power plug with wet hands.
This may result in electric shock.
Use only the type of power source indicated on the product’s label.
Also, do not plug the power cord into an outlet with many other cords
connected to it.
Using an out-of-spec power source may result in electric shock or fire.
Do not use a damaged power cord.
This may result in electric shock or fire.
If the power cord is damaged, consult your dealer for repairs.
Observe the following when handling the power cord.
•Do not modify the power cord
•Do not place heavy objects on the power cord
•Do not bend, twist or pull the power cord by force
•Do not wire heating appliances nearby
Be careful when handling the power plug.
Mishandling may result in fire.
•Do not leave plugged into a power source having foreign matter such as
dust
•Firmly insert the prongs of the power plug all the way
When you disconnect the power plug from the outlet, be sure to turn off the
power and hold the plug as you pull.
If you stretch the power cord, it may become damaged, which could result in
electric shock or fire.
Be sure your AC power cord meets the relevant local safety standard. Also, do
not use the power cord included with this product with any other devices.
This may result in electric shock or fire.
For safety reasons, be sure to ground the power cord.
The power cord included with the product is a 3-pin cable with a power
system grounding (PE) terminal, so connect it to an outlet with a grounding
electrode and ground it securely.
CAUTION
Regularly disconnect the power plug from the outlet and clean the base of the
prongs and between the prongs.
If you leave the power plug connected to an outlet for a long time, the base
of the power plug prongs may become dusty, which may result in short circuit
and fire.
For safety, be sure to disconnect the power plug from the outlet when you will
not be using the product for a long time.

9
Before Using This Product
Cautions for using
WARNING
Do not continue to use under abnormal conditions such as smoke, unusual
odors or sounds.
This may result in electric shock or fire.
Immediately turn off the power, disconnect the power plug from the outlet,
and contact your dealer or the Epson Repair Center about repairs. Servicing
the product yourself is dangerous, so never attempt it.
Do not insert or drop metal or flammable objects into the air vents or other
openings.
This may result in electric shock or fire.
If a foreign object, water or other liquid enters the product, do not continue to
use it.
This may result in electric shock or fire.
Immediately turn off the power, disconnect the power plug from the outlet,
and contact your dealer or the Epson Repair Center about repairs.
Do not attempt to service the product yourself.
This may result in injury, electric shock, fire or malfunction.
Do not leave containers of water or other liquid on this product.
If water spills on or into the product, this may result in electric shock, fire, or
malfunction.
CAUTION
Do not step on or place heavy objects on top of the product.
Be especially careful in households with small children. There is a risk that it
could fall over or break, resulting in injury.
Do not use the various cables (cords) to connect the product in a way other
than that specified in the instruction guide.
Faulty wiring may result in fire.
Do not connect a telephone line to the Ethernet interface connector.
This may result in damage to the telephone line or this product.
When connecting this product to a computer (or other device) using a cable,
be careful to orient the connector the right way.
The connectors on the cables have a specific orientation. If you connect
incorrectly oriented connectors to both this product and the computer (or
other devices), this may result in the malfunction of both connected devices.

10
CAUTION
When storing or transporting this product, do not tilt it, stand it on end, or turn it
upside down.
When transporting the product, be sure to package it in the original box to
protect it from any impact.
For safety reasons, if you move this product, first check that the power is off, the
power plug is disconnected from of the outlet, and all of the wires are
disconnected.
When replacing the ink cartridges, be careful that the ink does not contact
your eyes or skin.
Be especially careful because once an ink cartridge is used, there may be
some ink around the ink supply port. If ink gets into your eyes, immediately flush
them with water, and if it gets onto your skin, immediately wash the area with
soap and water. Leaving the ink as is may result in bloodshot eyes or mild
inflammation. In the rare event that there is a problem, immediately consult
with a physician.
Do not disassemble the ink cartridges to replenish or refill the ink.
Do not shake the ink cartridges too hard.
The ink cartridges may leak if you shake them around too much.
Store ink cartridges out of the reach of children. Also, do not ingest the ink.

11
Before Using This Product
WARNING
The connection of a non-shielded interface cable to this product will invalidate the EMC standards of this device. You
are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your
authority to operate the equipment.
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
FCC compliance statement for American users
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
For Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
For California customers only
The lithium batteries in this product contain Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.

12
Cautions for CD/DVD discs
Before using this product, run an operation check to make sure it is functioning normally. Also, back up the data on
CD/DVD discs onto separate media as necessary. Data may be damaged or lost at the following times:
•When there is static electricity or electrical noise
•During improper use
•During a malfunction or repair
•When there is damage due to a natural disaster
Even if the product is still under warranty, Epson accepts no responsibility for data that is lost or damaged due to
causes not limited to those listed above.
Uses of this product
This product is for business use and not for household use.
Incidental loss arising from the use of this product
Should you not obtain the results you expect from this product, including the bundled software, we cannot provide
compensation for incidental loss arising from that fact, such as expenses required for the use of this product and lost
earnings that would have been gained through the use of this product.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related to
aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc.; or functional/precision
devices etc., you should use this product only after giving consideration to including fail-safes and redundancies into
your design to maintain safety and total system reliability. Because this product was not intended for use in
applications requiring extremely high reliability/safety such as aerospace equipment, main communication
equipment, nuclear power control equipment, or medical equipment related to direct medical care etc., please make
your own judgment on this product’s suitability after a full evaluation.
About open source software licenses
This product uses open source software in addition to Epson proprietary software. For a list of the open source
software used in this product as well as license terms for this software, see Open Source Software License Agreement
on the PP-100/PP-100N Utility & Documents Disc included with the product.

13
PIN Controlled Mode and Security Mode
PIN Controlled Mode and Security Mode
In addition to the regular modes (Standard Mode/External Output Mode/Batch Mode), this product also has the two
modes PIN Controlled Mode and Security Mode. This section describes precautions for using the product in the PIN
Controlled Mode and Security Mode.
Publish Mode
PIN Controlled Mode
In PIN Controlled Mode, only a publisher authenticated using the identity authentication function can publish a disc
after the disc image and the label data file are created on the client computer. In addition, the disc that was published
can be received only by a publisher who enters a user number and PIN to be certified as the person who published the
disc.
Publisher
Publisher Publisher
Creates a disc data file Publishes the disc
Enters a user number and PIN Ejects the disc

14
Security Mode
In Security Mode, after the disc image and the label data file are created on the client computer, the publisher and the
approver are authenticated using the identity authentication function, and the disc is published only if the correct
approver approves disc publishing by the correct publisher using the approval workflow. In addition, the disc that
was published can be received only by a publisher who enters a user number and PIN to be certified as the person
who published the disc.
As a result, if you use Security Mode, published discs can no longer be passed to other people, which makes it
possible to prevent data recorded on discs from leaking.
What this product (PP-100N) protects is the data on the published disc that is stored on
this product. It does not protect the following data on this product.
•Source files on the file server or client computers as well as disc images and label data
files
•Disc images and label data files saved on the hard disc of this product as spool data
•Data on a published disc that was ejected from this product or to Stacker 4
Publisher Approver
Publisher Publisher
• Creates a disc data file
• Applies to have a disc
published
Approves publishing of
the disc
Publishes the disc
Enters a user number and PIN Ejects the disc

15
PIN Controlled Mode and Security Mode
Security control mechanisms
This product offers the following five security control mechanisms for implementing security functions that prevent
leaks of data stored on your discs when you use the PIN Controlled Mode and Security Mode.
•Controlled Distribution Function
Only the user who created the disc can eject a published disc.
•Electronic Lock Open Function
Only administrators are permitted to unlock the disc cover.
•Identity Authentication Function
Only registered users are permitted to operate this product using the control panel and the Web application software
included with the products (EPSON Total Disc Net Administrator), EPSON Total Disc Maker, and EPSON Total Disc
Monitor.
•Warning Function
Issues a warning to the administrator when there is a possibility of a security breach.
•Setting Data Control Function
Only users with authority are permitted to access setting control data, job information, and disc position information.
System configuration
The following items are required to use this product in Authentication Publish Option Mode.
Hardware
•Client computers for approvers (only when in Security Mode), administrators, and publishers
Software
•Total Disc Maker: Lets you write data to a disc, edit print data, and publish discs.
•Total Disc Setup: Lets you register the publish destination PP-100N.
•Total Disc Monitor: Shows the status of this product, and lets you show and change the status of a job.
•Internet Explorer 6/7: Used for EPSON Total Disc Net Administrator (Web application included with this
product).
Note: It is necessary to be protected from the external network using a router or firewall.
Depending on the usage environment, an external network, SMTP server, or file server may not be present.
External network
Router/
Firewall
Approver’s
client computer
Administrator’s
client computer File server
SMTP server
Publishers’
client computers
PP-100N

16
Secure disc creation
To use the Pin Controlled Mode/Security Mode in this product and build an environment for creating disc securely,
thoroughly familiarize yourself with the following information and start setup tasks.
Roles of the person in charge and the users (administrators, approvers, publishers)
To appropriately use the Pin Controlled Mode/Security Mode in this product, it is necessary to separate the roles of
the person in charge and the users (administrators, approvers, publishers). (In PIN Controlled Mode, it is not
necessary to appoint an approver.) Each of the roles is described below.
Who is the person in charge?
This is the head of the organization that installed this product.
Role of the person in charge
•Appoints administrators (more than one) who can be trusted and teaches the administrators the required
knowledge
•Appoints approvers who can be trusted
Who is a user?
A user is a person who has the authority to create discs using this product. This includes administrators, approvers
and publishers.
More details about the work performed by users are presented in the PP-100N Security User’s Guide.
Role of an administrator
•Sets up, operates, and manages this product
•Trains approvers and publishers in how to install the software
•Trains approvers and publishers in how to operate the product
•Responds when there is a possibility of a breach of security
More information about the work that administrators perform is presented in this guide.
Role of an approver
•Approves the creation of discs
More information about the work that approvers perform is presented in Approving/ Rejecting Job Applications in
the PP-100N Security User’s Guide.
Role of a publisher
•Creates discs
•Applies for creation of
discs (Security Mode only)
Related personnel
in the organization
Head of the organization
Users
Administrators Approvers Publishers

17
PIN Controlled Mode and Security Mode
What is a secure disc creation environment?
There is a risk of information leaks in environments where appropriate conditions are not met. Check the following
issues.
•The person in charge must appoint people who can be trusted to be administrators and approvers (Security Mode
only).
•People with knowledge of IT must be appointed as administrators.
•Several administrators who can always monitor the status of this product and who can respond quickly if a
warning or error occurs must be appointed.
•Administrators must sufficiently understand the information in this guide in advance.
•Users themselves should manage user authentication information (passwords and PINs) used for identity
authentication so that it is not used by third parties.
•Administrators must manage disc cover keys very carefully so that they are not used by anyone other than
administrators.
•Measures such as making firewall and router security settings must be implemented so that this product is not
subject to an attack from an external network.
•Measures must be taken to protect the data that flows within the internal network from hacking so that user
authentication information (passwords and PINs), JOB data, and other information is not leaked.
•Measures must be taken to monitor the network so that the NTP server or DNS server is not falsified.
•An administrator must be present when a third party other than an administrator, such as a service engineer, sets
up the product or changes the settings.

18
Preparation
Installation
Install this product in a suitable location with adequate space.
CAUTION
•Make sure that the product is lifted by two people.
•The weight of this product is approximately 25.0 kg. When this product is lifted, it should
be lifted on both sides by two people holding the recesses on the sides as shown in the
illustration on the left. Holding any part other than the ones indicated in the illustration
on the left when carrying the product may result in damage to the product. In
particular, carrying the product while the disc cover, ink cartridge cover, or Stacker 4 is
open may result in the product being dropped, or deformed and damaged.
Furthermore, when putting down this product, take care not to trap a finger between
the product and installation surface.
•When lifting this product, make sure that, for example, you sufficiently bend
your knees and your posture is such that excessive stress is not placed on your
body.
An unnatural posture when lifting the product may result in an injury, or the product
being damaged.
•When moving the product, do not tilt it 10 or more degrees in a forward or
backward direction, or sideways direction.
The dropping or other mishandling of the product may result in an accident.
•Do not place a heavy object on the top of the product.
Subjecting this product to excessive force may result in a malfunction.
However, it is possible to place one unit of this product on top of another. In such a
case, make sure the tops and bottoms are oriented the same, and the exterior of the
units are aligned.
Take sufficient care to prevent a unit from dropping or falling. Also, do not
place more than one unit on top of another.
•In a location where static electricity is easily generated, use an antistatic mat and
other product to prevent static electricity.
•Do not install this product in locations with large amounts of dust, dirt, or cigarette
smoke.
•Do not use or store in high-temperature, high-humidity environments. This can cause
the label surfaces to blur and stick together.

19
Preparation
Installation location requirements
Install this product in the following type of location.
•Flat, stable location that can fully support the product weight (approx. 25.0 kg)
•Location that is wide enough to fully hold the product base
•Location where the air vents on the product are not blocked
•Location where the product is not subjected to vibrations or jolts
•Location where the product has access to its own dedicated power outlet
•Location that allows disc loading and unloading
•Location with sufficient space for attaching accessories, replacing consumables, and enabling regular maintenance
and care
•Location that satisfies the following requirements
Installation space
Provide enough installation space for facilitating the installation work. If you place the product by the
wall, leave more than 10 cm between the back of the product and the wall. It is also necessary to leave
enough space in front of the product to open and close the disc cover.
* Be sure to leave at least 7 cm on the product left side for opening the ink cartridge cover.
Temperature Operation: 10 to 35°C, Storage: -20 to 40°C (Less than one month if at 40°C)
Humidity Operation: 20 to 80% RH, Storage: 5 to 85% RH (no condensation)

20
Setup procedure
This section describes the setup procedure for this product (PP-100N).
Before starting setup, check that all protective tape and protective materials attached to
this product have been removed. See PP-100N Security Setup Guide for the procedure to
remove the protective materials.
1. Connecting the authentication keypad on page 21 in this guide
5. Setting the security lock switch on page 30 in this guide
4. Installing the ink cartridges on page 26 in this guide
3. Connecting the power cord on page 25 in this guide
2. Connecting the Ethernet cable on page 25 in this guide
7. Network settings on page 36 in this guide
9. System settings on page 47 in this guide
8. Registering an administrator on page 42 in this guide
10. Installing digital certificates on page 56 in this guide
6. Setting the Publish Mode on page 31 in this guide