Epson EPL-N4000 User manual

Flamingo
Rev. C
A5 size COVER.FM
11/5/98 Pass 0
LProof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
Printer Parts
power switch
control panel
front cover
lower cassette 1
lower cassette 2
cover B
extention
MP tray
paper guide
face-down tray
cover A
stopper Type-B
interface
connector
optional Duplex Unit
connector
optional Multibin Unit
connector
optional Large
Capacity Paper Unit
connector
AC inlet
Ethernet interface
connector
parallel
interface
connector

Proof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
Flamingo
Rev. C
A5 size Setup2.toc
11/5/98 Pass 0
R
Hardware Setup Guide
Contents
1 Installing the Large Capacity Paper Unit. . . . . . . . . . . . . 1
2 Installing the Imaging Cartridge . . . . . . . . . . . . . . . . . . . 8
3 Loading Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Attaching the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . 17
5 Test Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Connecting the Printer to a Computer . . . . . . . . . . . . . . . 19
7 After Setting Up the Hardware. . . . . . . . . . . . . . . . . . . . . 20

ii
Flamingo
Rev. C
A5 size Setup2.toc
11/5/98 Pass 0
LProof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
This booklet helps you set up your printer and begin printing quickly.
See the Reference Guide for information on using your printer and its
options, or if you have problems printing.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
General Notice: Other product names used herein are for identification purposes only and
may be trademarks of their respective owners. EPSON disclaims any and all rights in those
marks.
Copyright © 1998 by SEIKO EPSON CORPORATION, Nagano, Japan.

1
Flamingo
Rev. C
A5 size SETUP2.FM
11/5/98 Pass 0
R
Proof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
1
Installing the Large Capacity
Paper Unit
Install the Large Capacity Paper Unit when setting up the printer.
Skip this section if you will not use this option.
1. Open and unpack the shipping carton.
2. Cut the tape that holds the cardboard inserts.
3. Remove the inserts and all other protective materials inside
the box. Make sure the contents of the package match the
items on the included document. Remove the packaging
materials from the Large Capacity Paper Unit and store them
for future use.
cut here

2
Flamingo
Rev. C
A5 size SETUP2.FM
11/5/98 Pass 0
LProof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
4. Carefully lift the Large Capacity Paper Unit out of the box
with two or more people, and place it near the printer.
5. Lock the casters at the bottom of the unit by pushing their
levers down.

3
Flamingo
Rev. C
A5 size SETUP2.FM
11/5/98 Pass 0
R
Proof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
6. At the back of the unit, push the cable into the slot.
7. Carefully lift the printer with two or more people.
cCaution:
❏The printer weighs about 50 kg (110.2 lb); always lift it
with two or more people.
❏Grasp the printer at the locations indicated below.
left side right side

4
Flamingo
Rev. C
A5 size SETUP2.FM
11/5/98 Pass 0
LProof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
8. Align each of the printer’s corners with those of the unit, then
lower the printer until it rests securely on the unit.
9. Make sure all corners of the printer fit firmly onto the unit.

5
Flamingo
Rev. C
A5 size SETUP2.FM
11/5/98 Pass 0
R
Proof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
10. Pull out lower cassette 2 as far as it will go. Then, lift it up
slightly, and completely remove it.
11. Pull out lower cassette 3. Take out and open the included
package of metal fittings and screws.

6
Flamingo
Rev. C
A5 size SETUP2.FM
11/5/98 Pass 0
LProof Sign-off:
M.Takata _______
K.Nishi _______
K.Pipa _______
12. Attachthe two metal fittings with the screws as shown below.
Note that the shape of the two fittings are different.
13. Push cassette 3 back into the unit, then replace cassette 2.
14. Pull out cassette 4 and remove the protective materials inside.