Epson FX-850+ Dimensions

Product Support Bulletin
Subject:
Power Specifications
Date: 2/7/90 PSB No: P-0060
Page: 1 of 2
Originator: RFB
The following information is a list of the power requirements for
the Epson 9 and 24 pin printers and laser printers.
504 VA maximum

PSB No: P-0060
Page: 2 of 2
Product
1 Voltage 1
Max. Current
Consumption 1 Power Consumption 1 BTU/HR
LX810
1
120V
.7 Amp
84 VA maximum
I
286.69
T750 120V 1.0 Amp
120 VA maximum 409.56
T1000 120V .7 Amp 84 VA
maximum 286.69
If the power requirements of a particular Epson printer is not listed please
refer to the appropriate User's Manual for the electrical specifications.
In the event that the User's Manual is not available, locate the silver label
on the back of the Epson printer.
This is a reliable source for the electrical
requirements.
The following formula is used to calculate the electrical
power requirements:
VOLTAMPS is equivalent to WATTS
VOLTAMPS = Volts * Amps
AMPS
BTU/HR = Voltamps/Volts
= Watts * 3.413
Example:
120V * 1A = 120VA
120VA/120V = 1A
120VA is equivalent to 120W
120W * 3.413 = 409.56 BTU/HR
Heat output is rated in BTU/HR.

EPSON
EPSON AMERICA, INC. INFORMA
Product Support Bulletin
Subject: Tractor
Pin Alignment
Date: 5/15/89
PSB No: P - 0044
Page: 1 of 1
Originator: RP
bd
The purpose of this bulletin is to insure the proper installation and alignment of
the FX-850/1050 and LQ- 850/1050 push tractor assemblies.
There are two possible ways to install the tractor frame on the push tractor
assembly. If the frame is installed incorrectly, the tractor belt pins on the two
tractors will not be aligned, and the resulting printout appears to be slanted on
the page, or the perforated edge will be tom. This is caused by the marks on
the tractor shaft holders being 180 degrees ‘out of phase.’
When assembling a tractor, there are two grooves in the shaft, and two tabs
on the tractor shaft holder. lf the pins on both tractor belts are not aligned, it
will be necessary to disassemble the tractor, and rotate one tractor shaft holder
180 degrees, to bring it back into alignment with the other shaft holder.
Alignment can be verified by examining the marks in the shaft holders, which
will both be in the forward position when properly aligned, as shown in Figure
4- 51 below.
Figure 4-51. Tractor Assembly Phases

EPSON
EPSON AMERICA, INC.
SERVICE
PRODUCT SUPPORT BULLETIN
PSB NO.: P-0024
I
DATE: 8/01/88
PAGE: 1 of 1
SUBJECT: FX-850/1050 UNDOCUMENTED BUFFER FEATURE
The FX-850/1050 dot matrix printers support an important feature
that is currently undocumented in the printer's User's manual.
The FX-850/1050 printers have the ability to enable or disable
the input buffer. This feature is controlled from the printer's
front panel by holding down the Load/Eject button during power
The printer will beep once indicating that the buffer is
disabled or will beep twice indicating that it is enabled.
The
condition of the input buffer may be changed back by simply
repeating the above operation. The printer's Self Test feature
may be used to determine the current setting of the input buffer
without changing it.
Please refer to the Self Test examples shown
below.
Skip Perforation
None
Auto LF Depend on I/F
2-4 OFF
Input Buffer
Valid
"'#$X%-o*+,-
' GF$%a- ( )*+,-
./0123456789:;<=>?UBCDEF'GHIJKUlNOPQRSTUVWXYZC'
~~#$%a- ( )*+*
./0123456789:;<=>?8ABCDEFGHIJKLMNOPQRSTWWXYZC\
-./0123456789:;<=>[email protected]\l
sTwwxYzc\3 -
Skip Perforation None
2-3 OFF
Auto LF Depend on I/F 2-4 OFF
Input Buffer
Invalid
'"jW&'O*+,-./0123456789:;
' n#$%&' ( >*+
<=>?@ABCDEFGHIJKLMNOPQRSTWWXYZC
-./0123456789:;<=>?$DEFGHIJKLMNOPQRSTWWXYZ~\
"#$xh'O*+,k/0123456789
:;<=>?QABCDEFGHIJKLMNOPQRSTWWXYZ~\l
#$%a-( I*+,-
./0123456789:;<=>?6ABCDMWIJKLMNOPQRSTWWXYZC\l-
EPSON AMERICA SERVICE, 23610 TELO AVENUE, TORRANCE, CALIF. 90505

EPSON
EPSON AMERICA, INC.
INFORMATION
Product Support Bulletin
Subject:
Epson Dot - Matrix Printer Options and Accessories
Date: 8/1/89
Page: 1 of 2 PSB No: P-0017B
Originator: RFA
9 - PIN DOT MATRIX OPTIONS
LX-810 FX-850 FX-1050 DFX-5000
TRACTOR UNITS
PULL TRACTOR C800061
7311 -A 7312-A 8309-A
CUT SHEET FEEDERS
SINGLE BIN C806121
7339-A 7340-A
DOUBLE BIN
N/A
N/A 7346-A 7348-A N/A
RIBBONS
STANDARD (BLACK)
INTERFACE BOARDS
SERIAL
- 0K BUFFER
8143
8143 8143 8143
SERIAL
- 8K BUFFER
8148 8148 8148 8148
PARALLEL - 32K BUFFER
8172 8172 8172 8172
IEEE 488 - 8K BUFFER
8165 8165 8165 8165
8750 8750 8755 8766
CABLES
STANDARD IBM PARALLEL
SERlAL DB-25 TO DB-9
SERIAL DB-25 TO DB-25
C1-9E-A C1-9E-A C1-9E-A C1-9E-A
=I;
EiZx EEx
g:;
MISC. PRINTER ACCESSORIES
PRINTER STAND
CPD-552 CPD-552 KP - STAND 8501-A

PSB No: P-0017B
Page: 2 of 2
24 - PIN MATRIX OPTIONS
TRACTOR UNITS
PULL TRACTOR
CUT SHEET FEEDERS
SINGLE BIN
DOUBLE BIN
INTERFACE BOARDS
SERIAL - 0K BUFFER
- 8K BUFFER
PARALLEL - 32K BUFFER
IEEE 488 -
8K BUFFER
CABLES
STANDARD IBM PARALLEL
SERIAL DB-25 TO DB-9
SERIAL DB-25 TO DB-25
SERIAL DIN-6 TO DB-9
SERIAL DIN-6 TO DB-25
APPLE ][e. DB-25 TO DIN-6
APPLE ][c. DIN-6 TO DIN-5
FONT MODULES
COURIER
PRESTIGE
ELFi3
MULTI
MISC. PRINTER ACCESSORIES
WINDOWS DRIVER SOFTWARE
APPLE MAC LQ SOFTWARE
LQ PATCH SOFTWARE
PRINTER STAND
DCB-LQ2
El=
CPD-552
LQ-510 LQ-850 LQ-950 LQ-1050 LQ-2550
C800061
7311 -A 7313-A 7312-A 7314-A
C806121 7339-A 7345-A 7340-A N/A
N/A 7346-A 7347-A 7348-A 7343-A
7753 7767
N/A N/A
7768 7769
7754
N/A
7762
7763
7764
8143 8143 8143 8143
8143
8148 8148 8148 8148
8148
8172 8172 8172 8172
8172
8165 8185 8165 8165
8165
C1-9E-A
E-i
N/A
N/A
N/A
N/A
C1-9E-A
E-X
iz
8239
C1-9E-A
z:;
zi
8239
C1-9E-A
=I;
N/A
N/A
N/A
N/A
7400A 7400A 7400A 7400A 7400A
7401A 7401A 7401A
7401A
7401A
7402A 7402A 7402A 7402A 7402A
7403A 7403A 7403A 7403A 7403A
7407-A 7407-A 7407-A 7407-A 7407-A
DCB-LQ2
C842001
LQ1
CPD-552
DCB - LQ2
ZYO’
DCB-LQ2
C842001
LQ1
KP - STAND KP - STAND
DCB-LQ2
i?iF1
KP - STAND

EPSON AMERICA, INC.
EPSON
Product Support Bulletin
Subject:
Quick Reference for Printer Acoustic Noise Levels
Date: 6/5/91
PSB No: P-0016D
Page(s): 1 of 2 Originator: SLS
Sound intensity is measured in units called Bels (named after Alexander Graham Bell,)
or more commonly in tenths of this fundamental unit: decibels. In making noise
measurements a weighting network is applied in an attempt to match the frequency
response of the instrument to that of the human ear. The most common is the A
weighting network, with resulting measurements expressed in dB(A).
The following is a list of current product’s noise levels tested in accordance with
standards set by the International Standards Organization (ISO). The acoustic noise
levels for the 9 pin printers are averages while printing in Near Letter Quality (NLQ)
mode using continuous paper and are not guaranteed figures. The acoustic noise
levels for the 24 pin printers are averages while printing in Letter Quality (LQ) mode
using continuous paper and are not guaranteed figures. The acoustic noise levels for
the laser printers are averages while using single sheet paper and are not guaranteed
figures.
9 PIN PRINTERS
MODEL
1 NOISE LEVEL
II
LX-810 56 dB(A)
II
FX-850
FX-1050
56 dB(A)
56 dB(A)
II
DFX-5000
I
55 dB(A)
II
II
DFX-8000
I
55 dB(A)
II
24 PIN PRINTERS
LQ-510
LQ-1010
56 dB(A)
56 dB(A)
11 LQ-850 1 56 dB(A) 11

PSB No: P-0016D
Page: 2 of 2
MODEL NOISE LEVEL
LQ-860 55 dB(A)
LQ-1050 55 dB(A)
LQ-2550 55 dB(A)
LASER PRINTERS