Epson PictureMate Guide

Using PictureMate
With a Computer
CPD-19430
Printed in XXXXXX XX.XX-XX XXX

1
Installing Software and Connecting PictureMate
To connect PictureMate®Deluxe Viewer Edition, you’ll need this cable:
If you don’t have a USB cable, you can buy one from your local computer
dealer or from Epson.
®See the inside back cover for details.
When you’re ready to start, see the section for your computer system:
■For Windows,
®see below.
■For Macintosh,
®see page 9.
Installing PictureMate for Windows
First make sure PictureMate is NOT CONNECTED to your computer,
and REMOVE your memory card, if it’s inserted. Then:
1. Load a sheet of PictureMate
Photo Paper, glossy side up,
against the right edge of the
paper feeder. Slide the edge guide
against the paper and open the
output tray.
2. Press the On button to turn
on PictureMate.
3. Turn on your computer.
Type A to B
USB cable
On button
Usingwcomputer.fm Page 1 Tuesday, March 29, 2005 3:48 PM

2
4. Wait a minute for your computer to start up, then insert the
PictureMate CD in your CD-ROM or DVD drive.
After a moment, you see this screen:
5. Read the license agreement and click Agree.
Usingwcomputer.fm Page 2 Tuesday, March 29, 2005 3:48 PM

3
Note:
If you see a screen like this,
remove your memory card
from PictureMate and click the
Xin the upper right corner to
close the screen, if necessary.
Note:
If you see a New Hardware
Found message at the bottom
of your screen, click the Xin
the box to close it.
If you see a screen like this,
click Cancel and disconnect
PictureMate from your
computer. Then turn off your
computer and begin again at
step 3.
Usingwcomputer.fm Page 3 Tuesday, March 29, 2005 3:48 PM

4
6. When you see this screen, click Next to begin installing your software.
Usingwcomputer.fm Page 4 Tuesday, March 29, 2005 3:48 PM

5
After a few minutes, you see this screen:
7. Make sure PictureMate is turned on, then connect the square end of
your USB cable to the USB port on the back of PictureMate. Connect
the flat end of the USB cable to any USB port on your computer.
Make sure the handle is
all the wa
y
down in back
Usingwcomputer.fm Page 5 Tuesday, March 29, 2005 3:48 PM

6
8. If you see a prompt to restart your computer, click No.
9. When you see this screen, click No if you have another printer for
non-photo printing.
If PictureMate is your only printer, and you only print photos, click
Yes.
If you see a message about printing a test page, click OK to print. When
printing finishes, click Next to install additional software.
Continue with the instructions in the next section.
Usingwcomputer.fm Page 6 Tuesday, March 29, 2005 3:48 PM

7
Installing Additional Software for Windows
1. When you see this screen, you can install additional photo software:
2. Click Epson Software Film Factory, then click Install on the next
screen and follow the on-screen instructions.
Note:
If you are asked if you want to install QuickTime,
®click Yes and follow the
on-screen instructions; you don’t need a registration number. Also
uncheck the boxes for launching QuickTime and Film Factory™at the end
of their installations.
Usingwcomputer.fm Page 7 Tuesday, March 29, 2005 3:48 PM

8
3. Close any open windows to return to the Optional Software
installation.
4. Click Epson PhotoCenter Link, then click Add Icon on the next
screen and follow the on-screen instructions.
5. When you’re done installing software, click Exit. The registration screen
appears.
6. Follow the on-screen instructions to register PictureMate.
7. Remove and store your PictureMate CD.
8. Restart your computer.
Note:
If you have any problems installing the PictureMate software, see page 16.
You’re ready to print your photos! Insert your memory card or open your
photo file on your computer, as described in the on-screen User’s Guide.
Double-click the PictureMate Deluxe User’s Guide icon on your screen
to open the User’s Guide.
Usingwcomputer.fm Page 8 Tuesday, March 29, 2005 3:48 PM

9
Installing PictureMate for Macintosh
1. If you inserted a memory card, remove it from PictureMate.
2. Connect the square end of your USB cable to the USB port on the back
of PictureMate. Then connect the flat end of the USB cable to any open
USB port on your Macintosh.
3. Press the On button to turn on PictureMate.
4. Turn on your Macintosh and wait a minute for it to start up.
5. Insert the PictureMate CD in your CD-ROM or DVD drive.
Note:
If you have any problems installing the PictureMate software, see
page 16.
Usingwcomputer.fm Page 9 Tuesday, March 29, 2005 3:48 PM