Epson R2880 - Stylus Photo Color Inkjet Printer User manual

Epson Stylus Photo R2880
Managing Color
Printing With Epson Premium ICC Profiles
®

2
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. The information contained herein is designed only for use with this
Epson product. Epson is not responsible for any use of this information as applied to other
equipment.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by purchaser or
third parties as a result of: accident, misuse, or abuse of this product or unauthorized
modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the
use of any options or any consumable products other than those designated as Original
Epson Products or Epson Approved Products by Seiko Epson Corporation.
Responsible Use of Copyrighted Materials
Epson encourages each user to be responsible and respectful of the copyright laws when
using any Epson product. While some countries’ laws permit limited copying or reuse of
copyrighted material in certain circumstances, those circumstances may not be as broad as
some people assume. Contact your legal advisor for any questions regarding copyright law.
Trademarks
Epson and Epson Stylus are registered trademarks, and Epson Exceed Your Vision is a
registered logomark of Seiko Epson Corporation.
General Notice: Other product names used herein are for identification purposes only and
may be trademarks of their respective owners. Epson disclaims any and all rights in those
marks.
This information is subject to change without notice.
© 2008 Epson America, Inc. 8/08

Print With Adobe Photoshop 3
Introduction
For the most precise color in your prints, you can use profiles designed specifically
for your printer model and paper type. Basic profiles are installed with your
printer driver, and you may also have downloaded Premium ICC profiles from
Epson when you installed your printer software (or you can download them from
http://www.epson.com/SPR2880Profiles).
To print using Premium ICC profiles with Adobe®Photoshop®CS2, CS3, or
Adobe Photoshop Lightroom®, follow the instructions in these sections for your
operating system:
■“Windows Vista and XP” below
■“Mac OS X 10.5” on page 15
■“Mac OS X 10.3 to 10.4” on page 25
Windows Vista and XP
Follow the instructions in these sections:
■“Print With Adobe Photoshop” below
■“Print With Adobe Photoshop Lightroom” on page 9
Print With Adobe Photoshop
First set up your color management environment in Photoshop and assign a
profile to your image. Then select your print settings and print (the steps show
Photoshop CS3 screens).
Note:
Assigning a profile to your image doesn’t alter it, only the interpretation of it by your
software and how it appears on your monitor and in a printout. This is the best way to
improve the color balance and contrast in your image.

4Print With Adobe Photoshop
Set Up the Photoshop Environment
1. Open Photoshop.
2. Select Edit > Color Settings.
3. Select North America Prepress 2 from the Settings menu to set Adobe RGB
(1998) as the RGB working space and activate profile messages.
4. Click OK.
Follow the steps in the next section to open the photo you want to print and
assign a profile to it.
Assign a Profile to Your Photo
1. Open the photo you want to print.
2. If you see an Embedded Profile Mismatch message, select Use the
embedded profile and click OK.
If you see a Missing Profile message, select Assign working RGB: Adobe
RGB (1998) and click OK. When your image appears, evaluate the color
balance and contrast as displayed on your monitor. If it looks incorrect, select
Edit > Assign Profile.

Print With Adobe Photoshop 5
Select one of the following as the Profile setting:
■A different RGB working space (or Profile), such as ColorMatch RGB or
sRGB IEC61966-2.1
■A scanner profile for your scanner
■A camera profile for your digital camera
Also click the Preview box so you can see the effects of your profile choice on
the screen.
Tip:
This is most effective when your monitor is calibrated using a hardware device
such as the X-Rite®i1Display 2.
3. Click OK.
4. Select File, then select Page Setup.
5. Select the Size of your paper, the Source you’ll use to load it, and the correct
Orientation for your photo.
6. Click OK.
7. Select File, then select Print or Print with Preview.
Windows Vista
®
Windows
®
XP

6Print With Adobe Photoshop
8. Do one of the following:
■Photoshop CS3: Select EPSON Stylus Photo R2880 in the Printer list,
if necessary, then select Color Management.
■Photoshop CS2: Click More Options, if necessary, then select Color
Management.
9. Under Print, select Document.
10. Under Color Handling, select Photoshop Manages Colors (Photoshop
CS3) or Let Photoshop Determine Colors (Photoshop CS2).
11. Under Printer Profile, select a profile for your printer and the paper you’ll
use. If you’re printing with Epson Premium ICC profiles, select the profile
that also matches the print quality you want to use, such as:
Note:
Epson Premium ICC profiles can be identified with the suffix “.icc,” for example,
“SPR2880 PrmSmGls Photo.icc.”
SPR2880 PrmSmGls Photo.icc
Printer Paper Print quality

Print With Adobe Photoshop 7
12. For the Rendering Intent setting, select Relative Colorimetric.
Note:
If your image contains very saturated colors, select Perceptual. This reduces the
color saturation so that the colors fit within the printer’s color gamut.
13. Select the Black Point Compensation checkbox.
14. Click the Print button.
Follow the steps in the next section to select print settings to match the profile and
print.
Print Your Color-Managed Photo
1. Make sure the EPSON Stylus Photo R2880 is selected, then click the
Preferences or Properties button.
2. Select the Source and Media Type settings for the paper you’ll use for the
print.
3. Select Quality Options as the Print Quality setting.
You see a window like this one:
4. If you are using an Epson Premium ICC profile, set the Print Quality setting
to match your profile.
5. Turn off the High Speed and Edge Smoothing options, if they are
available, then click OK to close the Quality Options window.

8Print With Adobe Photoshop
6. Select Custom as the Mode setting, then choose Off (No Color Adjustment)
in the drop-down menu.
Note:
Make sure that you select Off (No Color Adjustment). If you don’t, the printer
driver will apply additional correction to the image, producing inaccurate results.
7. Click OK.
8. Click OK or Print to print.
If you get unexpected results, see “Solve Color Management Problems” on
page 37.
IMPORTANT:
Select Off (No
Color Adjustment)

Print With Adobe Photoshop Lightroom 9
Print With Adobe Photoshop Lightroom
First select your printer and page setup options in Lightroom. Then set the color
management options, select print settings, and print.
Select Color Management Options
1. Open Lightroom.
2. Select the photo you want to print.
3. Select the Print module, and click the Page Setup button.
4. Make sure the EPSON Stylus Photo R2880 is selected.

10 Print With Adobe Photoshop Lightroom
5. Select the Size of your paper, the Source you’ll use to load it, and the correct
Orientation for your photo.
6. Click OK.
7. Scroll down to the Print Job panel in Lightroom.
8. Under Color Management in the Print Job panel, select Other as the
Profile setting.

Print With Adobe Photoshop Lightroom 11
9. In the window that appears, select the profiles you want to add to the Profile
list that correspond to the printer and the papers you’ll use.
If you’re printing with Epson Premium ICC profiles, select the profiles that
also match the Print Quality you want to use, such as:
Note:
Epson Premium ICC profiles can be identified with the suffix “.icc,” for example,
“SPR2880 PrmSmGls Photo.icc.”
10. Click OK.
SPR2880 PrmSmGls Photo.icc
Printer Paper Print quality

12 Print With Adobe Photoshop Lightroom
11. Under Profile, select the profile for the paper you’re going to print on. If
you’re printing with Epson Premium ICC profiles, select the profile that also
matches the print quality you want to use, such as:
12. For the Rendering Intent setting, select Relative.
Note:
If your image contains very saturated colors, select Perceptual. This reduces the
color saturation so that the colors fit within the printer’s color gamut.
13. Click the Print button.
Follow the steps in the next section to select print settings to match the profile and
print.

Print With Adobe Photoshop Lightroom 13
Print Your Color-Managed Photo
1. Make sure the EPSON Stylus Photo R2880 is selected, then click the
Preferences or Properties button.
2. Select the Source and Media Type settings for the paper you’ll use for the
print.
3. Select Quality Options as the Print Quality setting.
You see a window like this one:
4. If you are using an Epson Premium ICC profile, set the Print Quality setting
to match your profile.
5. Turn off the High Speed and Edge Smoothing options, if they are
available, then click OK to close the Quality Options window.

14 Print With Adobe Photoshop Lightroom
6. Select Custom as the Mode setting, then choose Off (No Color Adjustment)
in the drop-down menu.
Note:
Make sure that you select Off (No Color Adjustment). If you don’t, the printer
driver will apply additional correction to the image, producing inaccurate results.
7. Click OK.
8. Click OK to print.
If you get unexpected results, see “Solve Color Management Problems” on
page 37.
IMPORTANT:
Select Off (No
Color Adjustment)

Print With Adobe Photoshop 15
Mac OS X 10.5
Follow the instructions in these sections:
■“Print With Adobe Photoshop” below
■“Print With Adobe Photoshop Lightroom” on page 20
Print With Adobe Photoshop
First set up your color management environment in Photoshop and assign a
profile to your image. Then select your print settings and print (the steps show
Photoshop CS3 screens).
Note:
Assigning a profile to your image doesn’t alter it, only the interpretation of it by your
software and how it appears on your monitor and in a printout. This is the best way to
improve the color balance and contrast in your image.
Set Up the Photoshop Environment
1. Open Photoshop.
2. Select Edit > Color Settings.

16 Print With Adobe Photoshop
3. Select North America Prepress 2 from the Settings menu to set Adobe RGB
(1998) as the RGB working space and activate profile messages.
4. Click OK.
Follow the steps in the next section to open the photo you want to print and
assign a profile to it.
Assign a Profile to Your Photo
1. Open the photo you want to print.
2. If you see an Embedded Profile Mismatch message, select Use the
embedded profile and click OK.
If you see a Missing Profile message, select Assign working RGB: Adobe
RGB (1998) and click OK. When your image appears, evaluate the color
balance and contrast as displayed on your monitor. If it looks incorrect, select
Edit > Assign Profile.
Select one of the following as the Profile setting:
■A different RGB working space (or Profile), such as ColorMatch RGB or
sRGB IEC61966-2.1
■A scanner profile for your scanner
■A camera profile for your digital camera
Also click the Preview box so you can see the effects of your profile choice on
the screen.
Tip:
This is most effective when your monitor is calibrated using a hardware device
such as the X-Rite i1Display 2.
3. Click OK.

Print With Adobe Photoshop 17
4. Select File, then select Page Setup.
5. Select EPSON Stylus Photo R2880 in the Format for pop-up menu, then
change the Paper Size, Source, and Orientation settings as necessary, and click
OK.
6. Select File, then click Print or Print with Preview.

18 Print With Adobe Photoshop
7. Do one of the following:
■Photoshop CS3: Select EPSON Stylus Photo R2880 in the Printer list,
if necessary, then select Color Management.
■Photoshop CS2: Click More Options, if necessary, then select Color
Management.
8. Under Print, select Document.
9. Under Color Handling, select Photoshop Manages Colors (Photoshop
CS3) or Let Photoshop Determine Colors (Photoshop CS2).
10. Under Printer Profile, select a profile for your printer and the paper you’ll
use. If you’re printing with Epson Premium ICC profiles, select the profile
that also matches the print quality you want to use, such as:
Note:
Epson Premium ICC profiles can be identified with the suffix “.icc,” for example,
“SPR2880 PrmSmGls Photo.icc.”
SPR2880 PrmSmGls Photo.icc
Printer Paper Print quality

Print With Adobe Photoshop 19
11. For the Rendering Intent setting, select Relative Colorimetric.
Note:
If your image contains very saturated colors, select Perceptual. This reduces the
color saturation so that the colors fit within the printer’s color gamut.
12. Select the Black Point Compensation checkbox.
13. Click the Print button.
Follow the steps in the next section to select print settings to match the profile and
print.
Print Your Color-Managed Photo
1. Select EPSON Stylus Photo R2880 in the Printer list.
2. Click dto expand the Print window, if necessary.
3. Select Print Settings from the pop-up menu.
4. Select the Media Type setting for the paper you’ll use for the print.
5. In the Color Settings pop-up menu, select Off (No Color Adjustment).
Note:
Make sure you select Off (No Color Adjustment). If you don’t, the printer driver
will apply additional correction to the image data, producing inaccurate results.
IMPORTANT:
Select Off (No
Color Adjustment)

20 Print With Adobe Photoshop Lightroom
6. If you are using an Epson Premium ICC profile, set the Print Quality setting
to match your profile.
7. Turn off the High Speed option.
8. Click Print to print your photo.
If you get unexpected results, see “Solve Color Management Problems” on
page 37.
Print With Adobe Photoshop Lightroom
First select your printer and page setup options in Lightroom. Then set the color
management options, select print settings, and print.
Select Color Management Options
1. Open Lightroom.
2. Select the photo you want to print.
3. Select the Print module, and click the Page Setup button.