Epson SC-F7100 series User manual

User's Guide
CMP0011-01 EN

Copyrights and Trademarks
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed
only for use with this Epson printer. Epson is not responsible for any use of this information as applied to other printers.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses
incurred by the purchaser or third parties as a result of accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to
this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those
designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
Seiko Epson Corporation shall not be held liable forany damage resulting from electromagnetic interference that occurs from the use of any interface cables
other than those designated as Epson Approved Products by Seiko Epson Corporation.
EPSON, EPSON EXCEED YOUR VISION, EXCEED YOURVISION and their logos are registeredtrademarks or trademarks of Seiko Epson Corporation.
Microsoft
®
, Windows
®
, and Windows Vista
®
are registered trademarks of Microsoft Corporation.
Intel
®
is a registered trademark of Intel Corporation.
PowerPC
®
is a registered trademark of International Business Machines Corporation.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any
and all rights in those marks.
© 2014 Seiko Epson Corporation. All rights reserved.
SC-F7100 Series/SC-F7000 Series User's Guide
Copyrights and Trademarks
2

Contents
Copyrights and Trademarks
Introduction
ImportantSafetyInstructions.................5
When choosing a place for this product. . . . . . . . 5
Whensettingupthisproduct...............5
Whenusingthisproduct...................5
Whenhandlingtheinkpacks...............6
NotesonThisGuide........................6
MeaningofSymbols......................6
Illustrations............................6
OperatingSystemVersions.................6
PrinterParts..............................7
Front (SC-F7100 Series). ..................7
Front (SC-F7000 Series). . . . . . . . . . . . . . . . . . 10
Slider................................13
LANport.............................13
Inside................................14
Back.................................15
Controlpanel..........................17
UnderstandingtheDisplay................18
Features................................20
RealizingHighProductivity................20
SuperiorEaseofUse.....................20
NotesonUsageandStorage..................21
Installationspace.......................21
Noteswhenusingtheprinter...............21
Noteswhennotusingtheprinter............22
Notes on Handling Ink Packs and Ink Tanks
....................................23
HandlingMedia........................23
UsingtheSuppliedSoftware.................25
ContentsoftheSoftwareDisc..............25
StartingEPSONLFPRemotePanel2.........26
ExitingEPSONLFPRemotePanel2.........26
UninstallingSoftware......................26
Basic Operations
LoadingandExchangingMedia...............27
LoadingMedia(SC-F7100Series)...........28
LoadingMedia(SC-F7000Series)...........33
ViewingandChangingMediaSettings........39
ExchangingMedia......................40
UsingtheAutoTake-upReelUnit.............42
MediaLoading(SC-F7100Series)...........42
Removing the Take-up Roll (SC-F7100 Series)
....................................48
Media Loading (SC-F7000 Series). . . . . . . ....50
Removing the Take-up Roll (SC-F7000 Series)
....................................55
BeforePrinting...........................56
Saving Optimal Settings for the Current Media
(PrintMediaSettings)......................57
Parameters Stored in Media Setting Banks. . . . . 57
SavingSettings.........................57
Changing the after heater temperature setting
(SC-F7100Seriesonly).....................62
Correcting Print Misalignment (Head
Alignment)..............................62
FeedAdjustment..........................64
UsingaTestPattern.....................64
Performing Feed Adjustment During Printing
....................................65
Printablearea............................66
Maintenance
DailyMaintenance........................68
Cleaning the Platen, Pressure Rollers, and
MediaHoldingPlates....................68
Checkingforcloggednozzles...............69
HeadCleaning.........................70
MaintenanceAroundthePrintHead...........71
PartCleaning:PreparationandNotes........71
HowtoClean..........................72
DisposingofWasteInk...................76
Replacing the Wiper and Wiper Cleaner. . . . . . 78
ChipUnitReplacementandInkRefills..........81
Time Period for Chip Unit Replacements and
InkRefills.............................81
ProcedureforReplacementandInkRefills.....81
DisposalofUsedConsumables...............84
PartsThatArePeriodicallyReplaced...........85
Using the Control Panel Menu
MenuOperations.........................86
MenuList...............................87
DetailsoftheMenu........................91
TheMediaSetupMenu...................91
PrinterSetupMenu......................96
TheMaintenanceMenu..................98
SC-F7100 Series/SC-F7000 Series User's Guide
Contents
3

ThePrintLogsMenu....................99
ThePrinterStatusMenu..................99
TheNetworkSetupMenu................ 100
ThePreferenceMenu................... 100
TheResetAllSettingsMenu..............101
Problem Solver
WhenaMessageisDisplayed................102
When a Maintenance Call/Service Call Occurs. . . 103
Troubleshooting......................... 104
You cannot print (because the printer does not
work)............................... 104
The printer sounds like it is printing, but
nothingprints.........................104
Theprintsarenotwhatyouexpected........105
Media...............................108
Others.............................. 110
Appendix
OptionsandConsumableProducts........... 111
SupportedMedia.........................112
MovingandTransportingthePrinter..........112
MovingthePrinter..................... 112
Transport............................ 113
Removing and Attaching the Media Guide Bar. . . 113
RemovingtheMediaGuideBar............ 113
AttachingtheMediaGuideBar............ 116
Paralleladjustment....................... 118
ParalleladjustmentusingToolA........... 119
Parallel adjustment using Tool B. . . . . . . . . . . 129
SystemRequirements..................... 144
SpecificationsTable.......................144
StandardsandApprovals.................145
Where To Get Help
TechnicalSupportWebSite.................146
ContactingEpsonSupport..................146
BeforeContactingEpson.................146
HelpforUsersinNorthAmerica...........147
HelpforUsersinEurope.................147
HelpforUsersinAustralia............... 147
HelpforUsersinSingapore...............148
HelpforUsersinThailand................148
HelpforUsersinVietnam................148
HelpforUsersinIndonesia...............148
HelpforUsersinHongKong..............149
HelpforUsersinMalaysia................149
HelpforUsersinIndia.................. 149
HelpforUsersinthePhilippines........... 150
Software License Terms
OpenSourceSoftwareLicenses.............. 151
Bonjour............................. 151
OtherSoftwareLicenses................... 156
Info-ZIPcopyrightandlicense.............156
SC-F7100 Series/SC-F7000 Series User's Guide
Contents
4

Introduction
Important Safety
Instructions
Read all of these instructions before using the printer.
Also be sure to follow all warnings and instructions
marked on the printer.
When choosing a place for this
product
❏Place this product on a flat, stable surface that is
larger than this product. This product will not
operate properly if it is tilted or at an angle.
❏Avoid places subject to rapid changes in
temperature and humidity. Also keep it away from
direct sunlight, strong light, or heat sources.
❏Avoid places subject to shocks and vibrations.
❏Keep this product away from dusty areas.
❏Place this product near a wall outlet where the plug
can be easily unplugged.
When setting up this product
❏This product’s power cord is for use with this
product only. Use with other equipment may result
in fire or electric shock.
❏Connect all equipment to properly grounded
power outlets. Avoid using outlets on the same
circuit as copiers or air control systems that
regularly switch on and off.
❏Avoid electrical outlets controlled by wall switches
or automatic timers.
❏Keep the entire computer system away from
potential sources of electromagnetic interference,
such as loudspeakers or the base units of cordless
telephones.
❏Use only the type of power source indicated on the
product’s label.
❏Use only the power cord that comes with this
product. Use of another cord may result in fire or
electric shock.
❏Do not use a damaged or frayed power cord.
❏If you use an extension cord with this product,
make sure the total ampere rating of the devices
plugged into the extension cord does not exceed the
cord’s ampere rating. Also, make sure the total
ampere rating of all devices plugged into the wall
outlet does not exceed the wall outlet’s ampere
rating.
❏If you plan to use the printer in Germany, observe
the following:
To provide adequate short-circuit protection and
over-current protection for this printer, the
building installation must be protected by a 10 or 16
amp circuit breaker.
❏If damage occurs to the plug, replace the cord set or
consult a qualified electrician. If there are fuses in
the plug, make sure you replace them with fuses of
the correct size and rating.
When using this product
❏Do not block or cover the openings in this product’s
cabinet.
❏Do not insert objects through the slots. Take care
not to spill liquid on this product.
❏Do not attempt to service this product yourself.
❏Unplug this product and refer servicing to qualified
service personnel under the following conditions:
The power cord or plug is damaged; liquid has
entered the product; the product has been dropped
or the cabinet damaged; the product does not
operate normally or exhibits a distinct change in
performance.
❏Do not move the print heads by hand; otherwise
you may damage this product.
❏Always turn the product off using the Power button
on the control panel. When this button is pressed,
the Power light flashes briefly then goes off. Do not
unplug the power cord or turn off the product until
the Power light stops flashing.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
5

❏SC-F7100 Series (model K191A) has two power
systems. There is a risk of electric shock unless the
two power cables are unplugged during the
maintenance.
When handling the ink packs
❏Keep ink packs out of the reach of children and do
not drink.
❏Wear protective eyewear, gloves, and a mask when
performing maintenance.
Should ink contact your skin or enter your eyes or
mouth, immediately take the following actions:
❏If fluid adheres to your skin, immediately
wash it off using large volumes of soapy
water. Consult a physician if the skin appears
irritated or is discolored.
❏If fluid enters your eyes, rinse immediately
with water. Failure to observe this
precaution could result in bloodshot eyes or
mild inflammation. If problems persist,
consult with a physician.
❏If fluid enters your mouth, consult a
physician immediately.
❏If fluid is swallowed, do not force the person
to vomit, and consult with a physician
immediately. If the person is forced to vomit,
fluid may get caught in the trachea which can
be dangerous.
Notes on This Guide
Meaning of Symbols
!
Warning: Warning: Warnings must be
followed to avoid serious bodily
injury.
!
Caution: Cautions must be followed to
avoid bodily injury.
c
Important: Important must be followed to
avoid damage to this product.
Note: Notes contain useful or
additional information on the
operation of this product.
Illustrations
The illustrations in this manual may differ slightly from
the actual objects they are intended to represent.
Operating System Versions
In this documentation, the following abbreviations are
used.
Windows refers to Windows 8, 7, Vista, XP.
❏Windows 8 refers to Windows 8, Windows 8 Pro,
and Windows 8 Enterprise.
❏Windows 7 refers to Windows 7 Home Basic,
Windows 7 Home Premium, Windows 7
Professional, and Windows 7 Ultimate.
❏Windows Vista refers to Windows Vista Home
Basic Edition, Windows Vista Home Premium
Edition, Windows Vista Business Edition,
Windows Vista Enterprise Edition, and Windows
Vista Ultimate Edition.
❏Windows XP refers to Windows XP Home Edition,
Windows XP Professional x64 Edition, and
Windows XP Professional.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
6

Printer Parts
Front (SC-F7100 Series)
AMaintenance cover (left)
Open this cover to clean the area around the print head. Normally closed when using the printer.
U“Cleaning Around the Print Head” on page 73
BAfter heater
The after heater can be used to rapidly dry ink after printing.
U“Heating & Drying(SC-F7100 Series only)” on page 58
CMedia guide bar
The media guide bar maintains tension to prevent the media sagging as it is taken up.
DHandle
After placing media on the left roll holder, rotate the handle to press the holder and apply pressure to the roll
core.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
7

ERoll core holder
Place the used roll core for media take-up on these holders. There are two supports: one on the left and one on the
right.
U“Media Loading (SC-F7100 Series)” on page 42
FRoll core holder locking screw
The locking screws keep the roll core holders in place once they have been attached to the roll core. There are two
supports: one on the left and one on the right.
GRoll support
Rest media temporarily on these supports when removing the take-up roll. There are two supports: one on the left
and one on the right.
HAdjustment screw
Use the adjustment screw when performing parallel adjustment.
IAutoswitch
Use this switch to select the auto take-up direction. Choose Off to disable auto take-up.
JManualswitch
Use this switch to select the manual take-up direction. The selected option takes effect when the Auto switch is in
the Off position.
KCasters
There are two casters on each leg. Once installation is complete, the front casters should be kept locked while the
printer is in use.
If the stand fixing screw is lowered too much, the caster rises off the floor. Do not use the printer when a caster is off
the floor.
LAirflow vents
These vents vent air from inside the printer. Do not obstruct these vents.
MWaste Ink Bottle holder
Place the Waste Ink Bottle in this holder.
NStand fixing screw
In addition to locking the casters, the stand fixing screws also keep the printer securely in place. The stand fixing
screws cannot be used for horizontal adjustment of the printer. After installing the printer, keep it securely in place
during use.
OWaste Ink Bottle
Waste ink collects in this bottle.
Replace with a new Waste Ink Bottle when the level approaches the line.
PStopper
The stopper prevents splatter when the waste ink is ejected.
Fit the stopper closely to the mouth of the Waste Ink Bottle in most situations.
QWaste ink tube
Waste ink is discharged from this tube. Be sure the end of this tube is in the Waste Ink Bottle while the printer is in
use.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
8

RInk tank
Holds ink used for printing.
SSlider
U“Slider” on page 13
TLock lever
Raise the lock lever to unlock the slider for removal when replacing the chip unit. Always lower the lock lever into
the locked position after inserting the slider.
UChip unit check lamp
This lamp turns on when a message related to the chip unit is displayed.
On : Check the contents of the error on the control panel’s screen and deal with the error.
Off : No error.
VAC inlet #1/AC inlet #2
Connects the power cable. Be sure to connect both cables.
WLAN port
U“LAN port” on page 13
XUSB port
Connects the USB cable.
YMaintenance cover (right)
Open this cover to perform maintenance around the print head. Normally closed when using the printer.
U“Maintenance Around the Print Head” on page 71
ZMedia loading lever
After loading media, lower the media loading lever to keep the media in place. Raise the lever to release the media
prior to removal.
aAlert lamp
This lamp lights or flashes when an error occurs.
On/Flashing : An error occurred. the type of error is indicated by how the lamp lights or flashes. Check the
contents of the error on the control panel’s screen.
Off : No error.
bControl panel
U“Control panel” on page 17
cFront cover
Open when loading media, cleaning the inside of the printer, or removing jammed media. Normally closed when
using the printer.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
9

Front (SC-F7000 Series)
AMaintenance cover (left)
Open this cover to clean the area around the print head. Normally closed when using the printer.
U“Cleaning Around the Print Head” on page 73
BEject guide
Media is ejected along this guide.
CRoll core holder
Place the used roll core for media take-up on these holders. There are two supports: one on the left and one on the
right.
U“Media Loading (SC-F7000 Series)” on page 50
DTensioner
The media guide bar maintains tension to prevent the media sagging as it is taken up.
ERoll core holder locking screw
The locking screws keep the roll core holders in place once they have been attached to the roll core. There are two
supports: one on the left and one on the right.
FRoll support
Rest media temporarily on these supports when removing the take-up roll. There are two supports: one on the left
and one on the right.
GAutoswitch
Use this switch to select the auto take-up direction. Choose Off to disable auto take-up.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
10

HManualswitch
Use this switch to select the manual take-up direction. The selected option takes effect when the Auto switch is in
the Off position.
ICasters
There are two casters on each leg. Once installation is complete, the front casters should be kept locked while the
printer is in use.
If the stand fixing screw is lowered too much, the caster rises off the floor. Do not use the printer when a caster is off
the floor.
JWaste Ink Bottle holder
Place the Waste Ink Bottle in this holder.
KStand fixing screw
In addition to locking the casters, the stand fixing screws also keep the printer securely in place. The stand fixing
screws cannot be used for horizontal adjustment of the printer. After installing the printer, keep it securely in place
during use.
LWaste Ink Bottle
Waste ink collects in this bottle.
Replace with a new Waste Ink Bottle when the level approaches the line.
MStopper
The stopper prevents splatter when the waste ink is ejected.
Fit the stopper closely to the mouth of the Waste Ink Bottle in most situations.
NWaste ink tube
Waste ink is discharged from this tube. Be sure the end of this tube is in the Waste Ink Bottle while the printer is in
use.
OInk tank
Holds ink used for printing.
PSlider
U“Slider” on page 13
QLock lever
Raise the lock lever to unlock the slider for removal when replacing the chip unit. Always lower the lock lever into
the locked position after inserting the slider.
RChip unit check lamp
This lamp turns on when a message related to the chip unit is displayed.
On : Check the contents of the error on the control panel’s screen and deal with the error.
Off : No error.
SAC inlet
Connects the power cable.
TLAN port
U“LAN port” on page 13
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
11

UUSB port
Connects the USB cable.
VMaintenance cover (right)
Open this cover to perform maintenance around the print head. Normally closed when using the printer.
U“Maintenance Around the Print Head” on page 71
WMedia loading lever
After loading media, lower the media loading lever to keep the media in place. Raise the lever to release the media
prior to removal.
XAlert lamp
This lamp lights or flashes when an error occurs.
On/Flashing : An error occurred. the type of error is indicated by how the lamp lights or flashes. Check the
contents of the error on the control panel’s screen.
Off : No error.
YControl panel
U“Control panel” on page 17
ZFront cover
Open when loading media, cleaning the inside of the printer, or removing jammed media. Normally closed when
using the printer.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
12

Slider
ASlider
Attach the chip unit included with the ink pack
before refilling the ink.
U“Chip Unit Replacement and Ink Refills” on
page 81
BInk inlet cover
Open this cover to refill the ink tank with ink.
CChip unit
A unit that includes an IC chip.
This is included with the ink pack.
LAN port
ARJ-45 connector
Connects the LAN cable. Use a shielded twisted pair
cable (category 5 or higher).
BData lamp (orange)
Indicates the network connection status and data
receive status by flashing and/or turning on.
On : Connected.
Flashing : Receiving data.
CStatus lamp (green/red)
The color indicates the network connection speed.
Red : 100Base-TX
Green : 1000Base-T
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
13

Inside
Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the
chapters listed in the reference sections below.
APrint head
The print head prints by moving left and right while emitting ink. Cleaning may be required depending on the
status.
U“Cleaning Around the Print Head” on page 73
BMedia holding plate
The media holding plates prevent the media riding up and keeps fibers on the cut edge of the media from touching
the print head. Position the plates at either side of the media before printing.
U“Loading Media (SC-F7100 Series)” on page 28
U“Loading Media (SC-F7000 Series)” on page 33
CCutter groove
Pass the blade of a cutter (available in the market) down this groove to cut media.
DPressure rollers
These rollers press down on the media during printing.
U“Cleaning the Platen, Pressure Rollers, and Media Holding Plates” on page 68
EPlaten
This part suctions the media for printing.
U“Cleaning the Platen, Pressure Rollers, and Media Holding Plates” on page 68
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
14

FWiper cleaner
The wiper cleaner removes ink from the wiper. It is a consumable; replacement may be required depending on the
status.
U“Replacing the Wiper and Wiper Cleaner” on page 78
GCaps
Except during printing, these caps cover the print head nozzles to prevent them drying out. Cleaning may be
required depending on the status.
U“How to Clean” on page 72
HWiper
The wiper removes ink from the print head nozzles. It is a consumable; cleaning or replacement may be required
depending on the status.
U“How to Clean” on page 72
U“Replacing the Wiper and Wiper Cleaner” on page 78
Back
ADrive switch
The drive switch is used to feed the media during loading and to rewind the media for replacement.
BRoll holder
Place media on these holders. There are two supports: one on the left and one on the right.
CRoll holder fixing screw
These screws fix the roll holders in place once the media has been installed. There are two supports: one on the left
and one on the right.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
15

DLift lever
If the media to be mounted on the roll holders seems heavy, use these levers to raise the media effortlessly to the
level of the roll holders. There are two supports: one on the left and one on the right.
ELoading guide
Media is loaded along this guide.
FRoll support
Rest media on these supports before placing it on the roll holders. There are two supports: one on the left and one on
the right.
GHandle
After placing media on the right roll holder, rotate the handle to press the holder and apply pressure to the roll
core.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
16

Control panel
APbutton (power button)
Turns the power on and off.
BPlight (power light)
The printer’s operational status is indicated by a lit or
flashing light
On : The power is on.
Flashing : The printer is receiving data or
performing head cleaning or other
operations during shut-down.
Off : The power is off.
CMbutton (media setup button)
Press this button to display the Media Setup menu,
which contains such items as Media Remaining,
Select Media, Customize Settings, and Print Media
List. This button is disabled during printing.
U“The Media Setup Menu” on page 91
DDisplay
Displays the printer's status, menus, error messages,
and so on. U“Understanding the Display” on
page 18
EMenu button
Press this button to display menus. U“Using the
Control Panel Menu” on page 86
Fybutton (back button)
Press this button to exit to the previous menu when
options are displayed. U“Menu Operations” on
page 86
Gl/rbuttons (left and right arrow buttons)
Use to position the cursor when performing such
tasks as entering a Setting Name or IP Address in
the setup menu.
Hu/dbuttons (media feed buttons)
❏When media is loaded, you can press the dbutton to
feed the media and the ubuttonto rewind. dKeep the
dbutton pressed to feed the media up to 103 cm.
Keep the dbutton pressed to feed the media up to 25
cm.
Note that when the ubutton is used to rewind, the
media will stop when its edge reaches the starting
print position. Rewind can be resumed by releasing
the button and then pressing it again.
❏When the menus are displayed, these buttons can be
used to select menu items and options. U“Menu
Operations” on page 86
IZbutton
❏When the menus are displayed, these buttons can be
used to select menu items and options.
❏Pressing this button when an option is highlighted
selects the highlighted item or performs the selected
operation.
❏If pressed when the warning buzzer is sounding, the
sound stops.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
17

Jbutton
SC-F7100 Series
Pressing this button displays the Heating & Drying
menu, where you can adjust the Heater
Temperature.
U“The Media Setup Menu” on page 91
SC-F7000 Series
Pressing this button when menus are displayed
closes the menus and returns the printer to ready
status.
K#button (maintenance button)
Pressing this button displays the Maintenance
menu, which contains such items as Nozzle Check,
Cleaning, Head Maintenance, and Waste Ink
Counter. This button is disabled during printing.
U“The Maintenance Menu” on page 98
LWbutton (pause/cancel button)
❏The printer enters pause status if this is pressed while
printing. To release the pause status, press the W
button again, or select Pause Cancel on the screen
and then press the Zbutton. To cancel print jobs
being processed, select Job Cancel on the screen and
then press the Zbutton.
❏Pressing this button when menus are displayed closes
the menus and returns the printer to ready status.
Mbutton (media feed button)
❏When the printer is in the ready state, you can feed the
media to the cut position by pressing this button and
then Z.
U“Cutting Media” on page 40
❏When printing is in progress, you can use this button
to adjust media feed.
U“Feed Adjustment” on page 64
Understanding the Display
The illustration shows the display for the SC-F7100
Series.
AMessages
Displays the printer’s status, operation, and error
messages.
U“When a Message is Displayed” on page 102
BHeater temperature
Displayed for the SC-F7100 Series only.
This display shows the temperature settings for the
after heater. The thermometer icons give a rough
indication of the current temperatures of the heaters.
: The heater has reached the selected
temperature.
: The heater has not reached the selected
temperature.
CFeed adjustment information during printing
Displayed when an adjustment value has been
entered during printing.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
18

DMedia info
❏From left to right, this display shows the selected
media, platen gap, media width, and media
remaining.
❏If a media setting bank number created with this
printer is selected as the print media, the number
(from 1 to 30) will be displayed. When RIP Settings is
selected, 0 will be displayed.
❏The selected platen gap is shown as follows.
:1.5
:2.0
:2.5
❏The media remaining is not displayed if Off is selected
for Remaining Setup in the MediaRemaining menu.
U“The Media Setup Menu” on page 91
EChip unit status
The display changes as shown below when an error is
detected in the installed chip unit.
Normal Warning or error
1 Status indicators
The chip unit status is indicated as follows.
: No error. Ready to print.
: An error occurred. Check the message
on the screen, and clear the error.
: The chip unit could not be recognized
or it is not compatible with the printer.
Or, the slider is not locked.
Check the on-screen message.
: Check the ink level in the ink tank, and
then replace the chip unit and refill the
ink correctly.
As it gets closer to time to replace the
chip unit, will begin to flash.
U“Chip Unit Replacement and Ink
Refills” on page 81
2 Ink color codes
BK : Black
Y:Yellow
M:Magenta
C:Cyan
FWaste Ink Bottle status
Displays the approximate amount of space available
in the Waste Ink Bottle. The display changes as
shown below when the waste ink bottle is nearly full
or an error occurs.
Normal Warning or error
1
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
19

1 Status indicators
The status of the Waste Ink Bottle is shown as
follows.
: No error. The indicator changes to
show the amount of space available.
: The Waste Ink Bottle is almost full.
Ready a new Waste Ink Bottle.
: The Waste Ink Bottle is full. Replace
with a new Waste Ink Bottle.
Features
This wide-format color ink jet printer supports roll
media 1626 mm (64 inches) in width. The main features
of this printer are described below.
Realizing High Productivity
Improving drying characteristics
The SC-F7100 Series is equipped with an after heater
that can be used to rapidly dry ink after printing.
Media Feeding Unit Accommodates High-Capacity
Rolls
The Media Feeding Unit can handle high-capacity rolls
with external diameters of up to 250 mm and weights of
up to 40 kg, ensuring that media require less frequent
replacement.
Auto Take-up Reel Unit Comes Standard
The auto take-up reel unit automatically takes up
printed media cleanly, with no wrinkles. This is useful
when printing large amounts or when performing
continuous overnight printing. The SC-F7100 Series
achieves the high-precision take-up necessary to
support continuous-type sublimation transfer printers.
High-capacity ink tank included
The printer includes a high-capcity ink tank for high
productivity. We also offer 1000 ml high-capacity ink
packs for ink refill. This eliminates the need for frequent
troublesome ink cartridge replacements.
Superior Ease of Use
Media Installation and Take up a Snap
The roll and roll core holders require no spindles,
eliminating the need to attach spindles before installing
media. Just bring the media to the printer and install it
directly. Never having to juggle long spindles makes
installing media a snap even where space is limited.
In addition to roll supports that give you a place to rest
media during installation, the printer offers lift levers
that allow heavy media to be effortlessly raised to the
level of the roll holders.
Ease of Maintenance
Print quality can only be ensured through daily
maintenance. The design of this printer leaves plenty of
space for maintenance, making maintenance a snap.
SC-F7100 Series/SC-F7000 Series User's Guide
Introduction
20