Epson SureColor F6000 Service manual

SEGroup Confidential Until: Permanent
Seiko Epson Corp.
COMMERCIAL PRINTER CS QUALITY ASSURANCE Dept.
Setting Guide (install)
SureColor F6000/B6000 series

SEGroup Confidential Until: Permanent
Revision Status
Revision Date of Issue Description
A March 8, 2013 First release
B August 27, 2014 Revised
Clear the package material
Correct mistakes

SEGroup Confidential Until: Permanent
< Caution >
Always wear gloves for assembly to avoid injury from sharp
metal edges.
When handling the ink packs
Wear protective eyewear, gloves, and mask when performing
maintenance.

SEGroup Confidential Until: Permanent
Content
1-1 Packaging (Main Unit)
1-2 Packaging (Ink Support Assy.)
1-3 Packaging (Ink Supply cover)
2-1 Assembly (Stand)
2-2 Assembly (Main unit + Stand)
3-1 Setting the Ink Support Assy.
3-2 Setting the Ink Tank
3-3 Confirming the Ink Tank position
3-4 Adjusting the Ink Tank height
3-5 Fixing the Ink Tank
3-6 Setting the Ink Supply cover
4-1 Fill ink into ink tank
5-1 FW update
6-1 Ink charge
7-1 Replace the Maintenance box
8-1 Nozzle check
9-1 Request for customer

SEGroup Confidential Until: Permanent
1-1 Packaging (Main Unit)
12
3
4
56
7
1. Printer
2. Adapter
3. Document pack
4. AC cable
5. Stand
6. Hex wrench
7. Hex bolt
（Fix the printer and
stand)

SEGroup Confidential Until: Permanent
1-2 Packaging (Ink Support Assy.)
8. Spacer (18pcs)
9. Plate B
10. Screw (for Ink tank)
Staite3×8 (4pcs)
11. Screw (for ink tank height)
3×18 (2 pcs)
12. Screw ( for Ink Support Assy.
4×8(10 pcs)
13. Ink Support Assy.
8
9
10 11
12
13

SEGroup Confidential Until: Permanent
1-3 Packaging (Ink Supply cover)
19. Ink Supply Cover
15. Plate C
14. Plate A
16. Hex bolt (Short)
(for Plate A and Plate C)
17. Hex bolt (Long)
(For Ink Supply cover )
18.Screw
(Ink supply ink and Plate
C)
3×8（2pcs）
14
15
16
17
18
19

SEGroup Confidential Until: Permanent
2-1 Assembly (Stand)
It is recommended to assemble the stand by a group of three.
Give the screws shown
in the figure a couple of
turns to fasten the
parts temporarily. The
items in the following
steps can not be
attached if the
screws are too tight.
Plate C Plate A

SEGroup Confidential Until: Permanent
Before using the
printer, be sure
the stand is
fixed in place.
When moving
the printer,
unlock the
casters.
Set Plate A to the Stand Right
You must set this plate before placing main unit on the stand. Set hex bolts temporarily.
2-1 Assembly (Stand)

SEGroup Confidential Until: Permanent
2-2 Assembly (Main unit + Stand)
When carrying the printer, use at least 4 persons.
When lifting the printer unit, only hold the highlighted area. Otherwise, it may
affect normal operation and printing.

SEGroup Confidential Until: Permanent
2-2 Assembly (Main unit + Stand)

SEGroup Confidential Until: Permanent
1. Set Ink support assy. (Black: 10 screws)
Main unit bottom front side
Main unit bottom
back side
Set Plate B （2 screws) temporarily
3-1 Setting the Ink Support Assy.

SEGroup Confidential Until: Permanent
3-2 Setting the Ink Tank
Put the CSIC Chips on the Slider Push topside and Insert the INKHOLDER
Caution:
See next
page
Set the Bk Ink Tank at first. (Most right side)
Set Ink Tank with reference to Ink Supply Cover

SEGroup Confidential Until: Permanent
Set to fit between cut position of Ink
Tank and hook of Ink Holder
Cut position of Ink Tank
Hook of Ink Holder
3-2 Setting the Ink Tank

SEGroup Confidential Until: Permanent
Check the depth of Hook
Good
Bad
Gap
3-2 Setting the Ink Tank

SEGroup Confidential Until: Permanent
3-3 Confirming the Ink Tank position
It is not enough to hold/insert
the ink tank.
ÆBad
It is enough to hold/insert the ink
tank.
ÆGood
If it is not enough to hold/insert the ink tank, please set this ink
tank again.
Check the vertical position of Ink Tank

SEGroup Confidential Until: Permanent
3-4 Adjusting the Ink Tank height
Check the front and rear position of Ink Tank
This Tank is not insert enough.
Bad
Good

SEGroup Confidential Until: Permanent
Adjusting plastics
for ink tank height.
(included 18pcs)
Set the white adjusting plastics one by one.
3-4 Adjusting the Ink Tank height
1. Right side 2. Left side
3. Right side 4. Left side

SEGroup Confidential Until: Permanent
5. Right side 6. Left side 7. Right side
Once you do not feel the
staggering (even if you find
there is No Gap ),
please set one more plastic
parts again.
<One time only!>
Set one more
plastic parts again.
Not feel the
staggering Don’t push ink tanks up
during inserting adjusting
plastics.
3-4 Adjusting the Ink Tank height

SEGroup Confidential Until: Permanent
3-5 Fixing the Ink Tank
Holding down the Ink Tank
and tighten 4pcs screws to
hold ink tank itself.