Epson EB-4955WU User manual

User's Guide

Notations Used in This Guide
•Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
Please understand and respect these caution symbols in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
•General information indications
Attention
Indicates procedures which may result in damage or injury if sufficient care is not taken.
a
Indicates additional information and points which may be useful to know regarding a topic.
sIndicates a page where detailed information regarding a topic can be found.
g Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
section of the "Appendix".
s"Glossary" p.151
[Name] Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Menu Name Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness

Notations Used in This Guide ........................ 2
Introduction
Part Names and Functions ................................... 8
Front/Top...................................................8
Rear....................................................... 9
Interface....................................................9
Base......................................................10
ControlPanel................................................11
RemoteControl ...............................................12
Replacingtheremotecontrolbatteries ............................. 14
Remotecontroloperatingrange.................................15
Preparing the Projector
Installing the Projector ..................................... 18
InstallationRequirements........................................18
ScreenSettings ...............................................19
Adjustingthepositionoftheimageontheprojectedscreen..............20
DisplayingaTestPattern........................................21
AdjustingthePositionoftheProjectedImage(LensShift)..................22
AdjustingtheImageSize........................................ 24
CorrectingtheFocus...........................................24
AdjustingtheImagePosition.....................................24
AdjustingtheHorizontalTilt......................................24
IDSettings..................................................25
SettheprojectorID..........................................25
CheckingtheProjectorID...................................... 25
SettingtheremotecontrolID...................................25
SettingtheTime..............................................26
Connecting Equipment ..................................... 28
ConnectingaComputer ......................................... 28
ConnectingImageSources.......................................30
ConnectingExternalEquipment...................................32
ConnectingaLANCable ......................................... 33
InstallingtheWirelessLANUnit.................................... 34
AttachingtheCableCover.......................................35
Attaching ................................................. 35
Basic Usage
ProjectingImages ......................................... 38
Automatically Detect Input Signals and Change the Projected Image (Source Search)
..........................................................38
SwitchingtotheTargetImagebyRemoteControl.......................39
AdjustingtheVolume..........................................39
AdjustingProjectedImages ................................ 40
CorrectingDistortionintheProjectedImage...........................40
H/V-Keystone..............................................40
QuickCorner...............................................41
ArcCorrection ..............................................42
PointCorrection............................................43
SelectingtheProjectionQuality(SelectingColorMode)...................44
Projecting 3D images(EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only)
........................................................45
ChangingtheAspectRatiooftheProjectedImage ......................45
Changingmethods.......................................... 46
AdjustingtheImage...........................................48
Hue,Saturation,andBrightnessAdjustment.........................48
GammaAdjustment .......................................... 49
CorrectingtheColorDifferencewhenProjectingfromMultipleProjectors.......50
Summaryofcorrectionprocedure................................50
Correcting................................................50
Useful Functions
ProjectionFunctions ....................................... 53
ProjectingTwoImagesSimultaneously(SplitScreen) .....................53
Contents
3

Operatingprocedures........................................53
Restrictionsduringsplitscreenprojection ........................... 55
HidingtheImageandSoundTemporarily(A/VMute).....................56
FreezingtheImage(Freeze)......................................57
EnlargingPartoftheImage(E-Zoom)................................ 57
SavingaUser'sLogo...........................................58
MemoryFunction .......................................... 60
Saving/Loading/ErasingtheMemory................................60
SchedulingFunction ....................................... 62
SavingaSchedule .............................................62
SettingMethods............................................62
Editingaschedule........................................... 63
SecurityFunctions ......................................... 65
ManagingUsers(PasswordProtection) ............................... 65
KindsofPasswordProtection...................................65
SettingPasswordProtection....................................65
EnteringthePassword........................................66
RestrictingOperation...........................................67
ControlPanelLock...........................................67
Remotecontrolbuttonlock....................................68
Anti-TheftLock ............................................... 68
Installingthewirelock........................................69
Configuration Menu
Using the Configuration Menu .............................. 71
ListofFunctions ........................................... 72
ConfigurationMenuTable.......................................72
Networkmenu............................................. 73
ImageMenu .................................................74
SignalMenu .................................................75
SettingsMenu................................................77
ExtendedMenu...............................................78
NetworkMenu...............................................81
NotesonoperatingtheNetworkmenu .............................82
Softkeyboardoperations......................................83
Basicmenu ................................................83
WirelessLANmenu.......................................... 84
Securitymenu .............................................85
WiredLANmenu............................................87
Mailmenu................................................88
Othersmenu..............................................89
Resetmenu...............................................90
InfoMenu(DisplayOnly)........................................91
ResetMenu.................................................92
Troubleshooting
UsingtheHelp ............................................. 94
ProblemSolving ........................................... 95
ReadingtheIndicators .......................................... 95
WhentheIndicatorsProvideNoHelp ................................99
ProblemsRelatingtoImages .....................................100
Noimagesappear .......................................... 100
Movingimagesarenotdisplayed................................100
Projectionstopsautomatically ..................................101
ThemessageNotsupportedisdisplayed...........................101
ThemessageNoSignalisdisplayed.............................. 101
Imagesarefuzzy,outoffocus,ordistorted ......................... 102
Interferenceordistortionappearinimages......................... 102
The image is truncated (large) or small, the aspect is not suitable, or the image has
beenreversed.............................................103
Imagecolorsarenotright ..................................... 104
Imagesappeardark......................................... 105
ProblemswhenProjectionStarts.................................. 105
Theprojectordoesnotturnon ................................. 105
OtherProblems .............................................. 106
Nosoundcanbeheardorthesoundisfaint........................ 106
Theremotecontroldoesnotwork............................... 107
Nothingappearsontheexternalmonitor.......................... 108
Contents
4

Iwanttochangethelanguageformessagesandmenus ................ 108
Emailisnotreceivedevenifaproblemoccursintheprojector............ 108
Thebatterythatsavesyourclocksettingsisrunninglow.isdisplayed....... 109
CannotchangesettingsusingaWebbrowser....................... 109
AboutEventID ........................................... 110
Maintenance
Cleaning ................................................. 112
CleaningtheProjector'sSurface ...................................112
CleaningtheLens............................................ 112
CleaningtheAirFilter ..........................................112
Cleaningtheairfilter ........................................ 112
ReplacingConsumables ................................... 115
ReplacingtheLamp........................................... 115
Lampreplacementperiod.....................................115
Howtoreplacethelamp......................................115
Resettingthelamphours..................................... 118
ReplacingtheAirFilter ......................................... 118
Airfilterreplacementperiod................................... 118
Howtoreplacetheairfilter.................................... 118
NotesonTransportation .................................. 120
MovingNearby.............................................. 120
WhenTransporting........................................... 120
Preparingpackaging........................................ 120
Noteswhenpackingandtransporting............................ 120
ImageMaintenance ....................................... 121
PanelAlignment ............................................. 121
ColorUniformity............................................. 122
Appendix
NetworkFunctions ....................................... 126
UsingtheQuickWirelessConnectionUSBKey ......................... 126
Monitoring and Controlling ............................... 127
AboutEasyMPMonitor.........................................127
AboutMessageBroadcasting.................................. 127
ChangingSettingsUsingaWebBrowser(WebControl)................... 127
Projectorsetup ............................................ 127
DisplayingtheWebControlscreen...............................127
UsingtheMailNotificationFunctiontoReportProblems..................128
ReadingErrorNotificationMail................................. 128
ManagementUsingSNMP...................................... 129
DisplayingtheWebRemoteScreen................................ 129
ESC/VP21Commands..........................................130
Commandlist............................................. 130
Cablelayouts............................................. 131
AboutPJLink................................................132
About Crestron RoomView
®
..................................... 132
Operatingaprojectorfromyourcomputer......................... 133
Optional Accessories and Consumables .................... 137
OptionalAccessories .......................................... 137
Consumables............................................... 137
Screen Size and Projection Distance ........................ 138
Projection Distance (For EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU) .....138
ProjectionDistance(ForEB-4750W)................................ 140
ProjectionDistance(ForEB-4650/EB-4550)........................... 142
SupportedMonitorDisplays ............................... 144
SupportedResolutions......................................... 144
Computersignals(analogRGB)................................. 144
ComponentVideo .......................................... 144
Compositevideo ........................................... 144
Input signal from the HDMI port and DisplayPort (EB-4955WU/EB-4950WU/
EB-4855WU/EB-4850WU/EB-4750W) .............................. 145
Contents
5

Input signal from the HDMI port and DisplayPort (EB-4650/EB-4550) . .......145
Specifications ............................................ 146
ProjectorGeneralSpecifications...................................146
Appearance .............................................. 150
Glossary ................................................. 151
GeneralNotes ............................................ 153
TrademarksandCopyrights ......................................153
Index .................................................... 154
Contents
6

Introduction
This chapter explains the names for each part.

Unless otherwise specified, the illustrations used in this guide are for
EB-4950WU.
Front/Top
Name Function
AAir exhaust vent Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands
near the air exhaust vent, and do not place objects
that may become warped or damaged by heat near
the vent. Hot air from the air exhaust vent could
cause burns, warping, or accidents to occur.
Name Function
BFocus ring Adjusts the image focus.
s"Correcting the Focus" p.24
CZoom ring Adjusts the image size.
s"Adjusting the Image Size" p.24
DRemote receiver Receives signals from the remote control.
EStatus indicators The color of the indicators and whether they are flashing
or lit indicate the status of the projector.
s"Reading the Indicators" p.95
FAir intake vent
(air filter)
Takes in air to cool the projector internally.
s"Cleaning the Air Filter" p.112
GAir filter cover
operation knob
Use this knob to open the air filter cover.
s"Replacing the Air Filter" p.118
HWireless LAN unit
cover
When wirelessly connecting the projector to a computer,
remove this cover and install the optional wireless LAN
unit.
s"Installing the Wireless LAN Unit" p.34
IWireless LAN indicator Indicates the access status of the optional wireless LAN
unit.
s"Optional Accessories" p.137
JCable cover Cover for the rear interface cable connection section.
s"Attaching the Cable Cover" p.35
KVertical lens shift dial Turn the dial to move the position of the projected image
up or down.
s"Adjusting the Position of the Projected Image (Lens
Shift)" p.22
LLens shift dial lock Locks or releases the lens shift dials.
MHorizontal lens shift
dial
Turn the dial to move the position of the projected image
left or right.
s"Adjusting the Position of the Projected Image (Lens
Shift)" p.22
Part Names and Functions
8

Name Function
NLamp cover Open when replacing the projector's lamp.
s"Replacing the Lamp" p.115
OSecurity slot The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
s"Anti-Theft Lock" p.68
Rear
Name Function
APower inlet Connects to the power cable.
BInterface s"Interface" p.9
CControl panel s"Control Panel" p.11
DSpeaker Outputs audio.
ECable holder Insert the supplied cable clamp here to prevent the HDMI
cable from falling out.
sQuick Reference
Interface
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU
EB-4750W/EB-4650/EB-4550
Name Function
AAudio1 port Inputs audio from equipment connected to the Computer
port.
Part Names and Functions
9

Name Function
BComputer port For analog RGB signals from a computer and component
video signals from other video sources.
CBNC port For analog RGB signals from a computer and component
video signals from other video sources.
DMonitor Out port Outputs to an external monitor the analog signal from the
computer connected to the Computer port or the BNC
port. You cannot output signals input from other ports or
component video signals.
EAudio Out port Outputs audio from the currently projected image to an
external speaker.
FRS-232C port When controlling the projector from a computer, connect
it to the computer with an RS-232C cable. This port is for
control use and should not normally be used.
s"ESC/VP21 Commands" p.130
GRemote port Connects the optional remote control cable set and inputs
signals from the remote control. When the remote control
cable is plugged into the Remote port, the remote receiver
on the projector is disabled.
s"Optional Accessories" p.137
HAudio2 port Inputs audio from equipment connected to the BNC port.
IAudio-L/R port Inputs audio from equipment connected to the Video port
or the S-Video port.
JS-Video port For S-video signals from video sources.
KVideo port Inputs composite video signals from video sources.
LHDMI port Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with HDCP
g .
MAudio3 port Inputs audio from equipment connected to the
DisplayPort or the HDMI port.
NDisplayPort Inputs video signals from DisplayPort compatible
computers. This projector is compatible with HDCP
g .
OLAN port Connects a LAN cable to connect to a network.
Name Function
PService port This port is used by maintenance personnel to control the
projector. This should not normally be used.
Base
Name Function
ASecurity cable
installation point
Pass a commercially available wire lock through here and
lock it in place.
s"Installing the wire lock" p.69
Part Names and Functions
10

Name Function
BRear feet When setup on a surface such as a desk, turn to extend and
retract to adjust the horizontal tilt.
s"Adjusting the Horizontal Tilt" p.24
CScrew hole to fix the
cable cover
Screw hole to fix the cable cover in place.
s"Attaching the Cable Cover" p.35
DCeiling mount fixing
points (four points)
Attach the optional Ceiling Mount here when suspending
the projector from a ceiling.
s"Installing the Projector" p.18
s"Optional Accessories" p.137
EFront adjustable foot When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s"Adjusting the Image Position" p.24
Control Panel
Name Function
A[t] button Turns the projector power on or off.
B[Source Search]
button
Changes to the next input source that is sending an image.
s"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.38
Name Function
C[]/[ ] buttons •Displays the Control Panel Lock screen allowing you to
make settings to lock the control panel buttons.
s"Restricting Operation" p.67
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s"Using the Configuration Menu" p.71
s"Using the Help" p.94
D[] button •When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
•If pressed while projecting analog RGB signals from the
Computer port or the BNC port, you can automatically
optimize Tracking, Sync., and Position.
E[]/[ ] buttons •Displays a test pattern.
s"Displaying a Test Pattern" p.21
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s"Using the Configuration Menu" p.71
s"Using the Help" p.94
F[] /[ ] buttons •Displays the Info menu from the Configuration menu.
s"Info Menu (Display Only)" p.91
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s"Using the Configuration Menu" p.71
s"Using the Help" p.94
G[A/V Mute] button Turns the video and audio on or off.
s"Hiding the Image and Sound Temporarily (A/V
Mute)" p.56
Part Names and Functions
11

Name Function
H[Esc] button •Stops the current function.
•If pressed when the Configuration menu is displayed, it
moves to the previous menu level.
s"Using the Configuration Menu" p.71
I[]/[ ] buttons •Performs screen adjustments using the settings in
Geometric Correction from the Configuration menu.
sSettings - Geometric Correctionp.77
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s"Using the Configuration Menu" p.71
s"Using the Help" p.94
J[Menu] button Displays and closes the Configuration menu.
s"Using the Configuration Menu" p.71
Remote Control
Part Names and Functions
12

Name Function
A[] button Turns the projector on.
B[t] button Turns the projector off.
CChange input buttons Changes to images from each input port.
s"Switching to the Target Image by Remote Control"
p.39
The [HDBaseT] button and the [SDI] button are not
available for this projector.
D[Auto] button If pressed while projecting analog RGB signals from the
Computer port or the BNC port, you can automatically
optimize Tracking, Sync., and Position.
E[Aspect] button Each time the button is pressed, the aspect mode changes.
s"Changing the Aspect Ratio of the Projected Image "
p.45
F[Test Pattern] button Displays a test pattern.
s"Displaying a Test Pattern" p.21
G[Freeze] button Images are paused or unpaused.
s"Freezing the Image (Freeze)" p.57
H[Menu] button Displays and closes the Configuration menu.
s"Using the Configuration Menu" p.71
I[][ ][ ][ ]
buttons
•When the Configuration menu or the Help screen is
displayed, pressing these buttons selects menu items
and setting values.
s"Using the Configuration Menu" p.71
•When using the optional wireless mouse receiver,
pressing these buttons moves the pointer.
s"Optional Accessories" p.137
Name Function
J[] button •When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
s"Using the Configuration Menu" p.71
•Acts as a mouse's left button when using the optional
wireless mouse receiver.
s"Optional Accessories" p.137
K[Split] button Each time the button is pressed, the image changes
between projecting two images simultaneously by
splitting the projected screen, or projecting one image as
normal.
s"Projecting Two Images Simultaneously (Split Screen)
" p.53
L[Page] buttons
[[][]]
Moves to the previous or next image file when projecting
images from a computer connected via a network.
M[Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s"Adjusting the Volume" p.39
N[User1] button
[User2] button
[User3] button
Select any frequently used item from the eight available
Configuration menu items, and assign it to one of these
buttons. By pressing the button, the assigned menu item
selection/adjustment screen is displayed, allowing you to
make one-touch settings/adjustments.
s"Settings Menu" p.77
ONumeric buttons •Enter the Password.
s"Setting Password Protection" p.65
•Use this button to enter numbers in Network settings
from the Configuration menu.
P[ID] button Hold down this button and press the numeric buttons to
select the ID for the projector you want to operate using
the remote control.
s"ID Settings" p.25
Part Names and Functions
13

Name Function
Q[ID] switch Use this switch to enable (On)/disable (Off) ID settings for
the remote control.
s"ID Settings" p.25
RRemote port Connects the optional remote control cable set and
outputs signals from the remote control.
s"Optional Accessories" p.137
When the remote control cable is plugged into this remote
port, the remote control light-emitting is disabled.
S[Help] button Displays and closes the Help screen which shows you how
to deal with problems if they occur.
s"Using the Help" p.94
T[Num] button Hold down this button and press the numeric buttons to
enter passwords and numbers.
s"Setting Password Protection" p.65
U[E-Zoom] buttons
[z][x]
Enlarges or reduces the image without changing the
projection size.
s"Enlarging Part of the Image (E-Zoom)" p.57
V[Default] button Enabled when [Default]: Reset is displayed on the
configuration menu guide. The settings being adjusted are
returned to their default values.
s"Using the Configuration Menu" p.71
W[Esc] button •Stops the current function.
•If pressed when the Configuration menu is displayed, it
moves to the previous level.
s"Using the Configuration Menu" p.71
•Acts as a mouse's right button when using the optional
wireless mouse receiver.
s"Optional Accessories" p.137
X[A/V Mute] button Turns the video and audio on or off.
s"Hiding the Image and Sound Temporarily (A/V
Mute)" p.56
Name Function
Y[Color Mode] button Each time the button is pressed, the Color Mode changes.
s"Selecting the Projection Quality (Selecting Color
Mode)" p.44
Z[Search] button Changes to the next input source that is sending an image.
s"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.38
a[] button Illuminates the buttons on the remote control for
approximately 15 seconds. This is useful when using the
remote control in the dark.
bIndicator A light is emitted when outputting remote control signals.
cRemote control light-
emitting area
Outputs remote control signals.
Replacing the remote control batteries
If delays in the responsiveness of the remote control occur or if it does not
operate after it has been used for some time, it probably means that the
batteries are becoming flat. When this happens, replace them with new
batteries. Have two AA size alkaline or manganese batteries ready. You
cannot use other batteries except for the AA size alkaline or manganese.
Attention
Make sure you read the following manual before handling the batteries.
sSafety Instructions
a
Remove the battery cover.
While pushing the battery compartment cover catch, lift the cover
up.
Part Names and Functions
14

b
Replace the old batteries with new batteries.
Caution
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the batteries are inserted the correct way.
If the batteries are not used correctly, they could explode or leak causing
a fire, injury, or damage to the product.
c
Replace the battery cover.
Press the battery compartment cover until it clicks into place.
Remote control operating range
Part Names and Functions
15

a
•To restrict reception of the operation signals from the remote
control, set Remote Receiver.
sSettings - Remote Receiver p.77
•When using a remote control provided with other Epson projectors,
set the Remote Control Type.
sExtended - Operation - Remote Control Type p.78
The operating range depends on the remote control that you use.
Part Names and Functions
16

Preparing the Projector
This chapter explains how to install the projector and connect projection sources.

Installation Requirements
The projector supports the following four different projection methods.
Install the projector according to the conditions of the installation location.
•Project images from in front of
the screen. (Front projection)
•Project images from behind a
translucent screen. (Rear projec‐
tion)
•Suspend the projector from the
ceiling and project images from
in front of a screen. (Front/Ceil‐
ing projection)
•Suspend the projector from the
ceiling and project images from
behind a translucent screen.
(Rear/Ceiling projection)
Warning
•A special method of installation is required when suspending the projector
from a ceiling (ceiling mount). If installation work is not carried out
correctly, the projector could fall down. This may result in injury or
accidents.
Contact your dealer or the nearest address provided in the Support and
Service Guide if you want to use this installation method. sEpson Projector
Contact List
•If you use adhesives on the Ceiling mount fixing points to prevent the screws
from loosening, or if you use things such as lubricants or oils on the
projector, the projector case may crack causing it to fall from its ceiling
mount. This could cause serious injury to anyone under the ceiling mount
and could damage the projector.
When installing or adjusting the ceiling mount, do not use adhesives to
prevent the screws from loosening and do not use oils or lubricants and so
on.
•Do not cover the projector's air intake vent or air exhaust vent. If either of
the vents are covered, the internal temperature could rise and cause a fire.
Attention
Do not use the projector on its side. This may cause malfunctions to occur.
Installing the Projector
18

a
•An optional ceiling mount is required when suspending the
projector from a ceiling.
s"Optional Accessories" p.137
•The default Projection setting is Front. You can change from Front
to Rear from the Configuration menu.
sExtended - Projection p.78
•You can change the Projection mode as follows by pressing down
the [A/V Mute] button on the remote control for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
•When mounted on a ceiling, set Inv Direction Button to On so that
the operations and movement of the [ ], [ ], [ ], and [ ]
buttons on the control panel match.
sExtended - Operation - Inv Direction Button p.78
The projector can be installed at the following angles.
Vertical: Tilt up to ±30°. If you use the projector tilted at an angle of more
than 30° it could be damaged and cause an accident.
30
30
30
30
Horizontal: Can be tilted within the range of expansion and contraction for
the rear feet.
s"Adjusting the Horizontal Tilt" p.24
Make sure there is a gap of at least 50 cm between the wall and the air
exhaust vent and the air intake vent.
Air exhaust vent
Air intake vent
When setting up multiple projectors, make sure there is a gap of at least
50 cm between the projectors.
Screen Settings
Set the Screen Type according to the aspect ratio of the screen being used.
The area where the image is displayed matches the shape of the screen.
a
Press the [Menu] button while projecting.
s"Using the Configuration Menu" p.71
b
Select Display from Extended.
Installing the Projector
19

c
Select Screen Type from Screen.
d
Select the screen's aspect ratio.
The shape of the background test pattern changes depending on the
setting.
e
Press the [Menu] button to finish making settings.
a
•This setting is unavailable when projecting images from a computer
over a network.
•When you change the Screen Type, adjust the aspect ratio for the
projected image as well.
s"Changing the Aspect Ratio of the Projected Image " p.45
•Make sure you install the EasyMP Network Projection application
from the EPSON Projector Software CD-ROM. When using an older
version of the application, images are not projected correctly. You
can download the latest version of EasyMP Network Projection from
the following Web site.
http://www.epson.com/
•This function does not support Message Broadcasting (an EasyMP
Monitor plugin).
Adjusting the position of the image on the projected screen
You can adjust the position of the image if there are margins between the
edge of the image and the projected screen frame due to the Screen Type
setting.
Example: When the Screen Type is set to 4:3 for EB-4950WU
You can move the image to the left and right.
a
Press the [Menu] button while projecting.
s"Using the Configuration Menu" p.71
b
Select Display from Extended.
c
Select Screen Position from Screen.
d
Use the [ ], [ ], [ ], and [ ] buttons to adjust the position of
the image.
You can check the current display position by using the background
test pattern.
Installing the Projector
20