Equinox Systems EQLED407 User manual

Order code: EQLED407
Detonator Control
User Manual

www.prolight.co.uk Detonator Control User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modications to this equipment are not subject to warranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and
the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage
connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when
equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available mains supply voltage is
between 220~240V AC, 50/60Hz.
• Make sure that the power cable is never crimped or
damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualied
engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic
temperature uctuation (e.g. after transportation),
do not connect power or switch it on immediately.
The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the
original packing material), and return it to your Pro Light
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be
carried out by a qualied technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• This xture is for professional use only - it is not designed
for or suitable for household use. The product must be
installed by a qualied technician in accordance with local
territory regulations. The safety of the installation is the
responsibility of the installer. The xture presents risks of
severe injury or death due to re hazards, electric shock
and falls.
• WARRANTY: One year from date of purchase.

www.prolight.co.uk Detonator Control User Manual 3
POWER
ON
OFF
ONOFF ONOFF ONOFF ONOFF
4321
POWER INPUT:
220-240V~50/60Hz POWER OUTPUT
FUSE:
F3A 250V
FUSE:
F3A 250V
POWER CONSUMPTION: 3W
Product overview & technical specications
This 4 channel control system is ideal for ring a wide
variety of special effects machines including the C-Shot.
• 4 channels
• Safety key
• Safety switches
• 4 powerCON output channels
• PowerCON input
• PowerCON output cables
not included
Detonator Control
Specications
Power supply 220-240V, 50/60Hz
Fuse F3A 250V
Dimensions 120 x 280 x 190mm
Weight 2.8kg
Order code EQLED407
01
02
03
04
05
06
280mm
190mm
120mm
POWER
ON
OFF
ONOFF ONOFF ONOFF ONOFF
4321
POWER INPUT:
220-240V~50/60Hz POWER OUTPUT
FUSE:
F3A 250V
FUSE:
F3A 250V
POWER CONSUMPTION: 3W
01 - Power ON/OFF safety key switch
02 - Fire/detonate safety key switches
03 - Fire/detonate switches
04 - Fuses F3A 250V
05 - PowerCON outputs
06 - PowerCON input
POWER
ON
OFF
ONOFF ONOFF ONOFF ONOFF
4 3 2 1
POWER INPUT:
220-240V~50/60Hz POWER OUTPUT
FUSE:
F3A 250V
FUSE:
F3A 250V
POWER CONSUMPTION: 3W
Operation:
The Detonator Control is designed to control multiple products including confetti cannons,
kabuki drops and CO2.
Connect the powerCON cable to the powerCON input on the unit (6), then connect the ring device to the
Detonator Control via the powerCON outputs (5). To prepare the controller for use, rst unlock the panel
by turning the key to the ON position (1). Turn the safety switch for each channel to the ON position (2)
for the channels to be armed. When the corresponding red re button (3) is pushed, the device will
activate. Turn the safety switch to the OFF position when the device is not in use.
POWER
ON
OFF
ONOFF ONOFF ONOFF ONOFF
4321
POWER INPUT:
220-240V~50/60Hz POWER OUTPUT
FUSE:
F3A 250V
FUSE:
F3A 250V
POWER CONSUMPTION: 3W
In the box: 1 x xture
& 1 x power input
cable

www.prolight.co.uk Detonator Control User Manual 4
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed of
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.