ERNITEC ECB Series User manual

Day&Night Hi-Res Colour CCD
Camera
ZEIM-0050696G A.3
CAUTIONS -----------------------------------------------------------------------------
SYSTEM COMPONENTS ---------------------------------------------------------
PIN CONNECTIONS -----------------------------------------------------------------
PARTS NAMES & FUNCTIONS --------------------------------------------------
PUSH BUTTONS AND THEIR FUNCTIONS ----------------------------------
SETTING MENU ----------------------------------------------------------------------
SUB MENU -----------------------------------------------------------------------------
OSD FUNCTION DESCRIPTION ------------------------------------------------
SYSTEM EXTENSIONS -------------------------------------------------------------
SPECIFICATIONS ---------------------------------------------------------------------
2
2
3
3
4
5
6
6
9
11

2
IMPORTANT SAFETY INSTRUCTIONS
1. CAUTIONS
Do not touch the imaging surface of
sensor. Use soft cloth moistened with
alcohol to clean the surface if it is
touched accidentally.
Ensure the supply voltage is correct
as specified for the particular variant of
camera before operation.
Do not expose the camera to rain,
moisture or to temperature outside the
specified limit, without a suitable
housing.
Avoid focusing directly on the sun.
Do not attempt to service this unit
yourself unless you are authorised to
do so. Opening the camera may
expose you to dangerous voltages
or other hazards. Refer all servicing to
qualified personnel only.
1)
2)
3)
4)
5)
3. SYSTEM CONNECTION
3.1 Basic System Connection
If connected to the mains :
THIS APPARATUS MUST BE EARTHED.
The wires on the mains lead are in
accordance with the following code :
GREEN/YELLOW ------------------Earth
BLUE ----------------------------------Neutral
BROWN ------------------------------Live
Warranty void if the S/N label on
camera is removed.
2. SYSTEM COMPONENTS
Camera -----------------------------------1
Instruction Manual ---------------------1
Lens Mounting Cap --------------------1
Hexagonal Wrench ---------------------1
AI Lens 4-pin Plug ----------------------1
6)
7)
NOTES OF USE

3
NOTES OF USE
3.2 Extended System Connection
4 PIN CONNECTIONS
5. PARTS NAMES & FUNCTIONS
Lens Mount (CS Mount) :
For installation of CS Mount lenses
only.
Tripod Stand :
Application for camera mounting onto
the camera holder. Effective for general
camera tripods.
Exposure Control :
a. Auto IRIS mode (two types of lens
are appropriate for this function):
DC IRIS lens :
Set the IRIS slide switch to the DC
position and adjust the LEVEL
control on the side panel to obtain a
clear picture.
1)
2)
3)
Video IRIS lens : Set the IRIS slide s
witch to the VIDEO position and
adjust the LEVEL and ALC controls
on the lens to obtain a clear picture.
b. Automatic Electronic Shutter ( AES ):
Set the IRIS slide switch to the AES
position to automatically adjust the
shutter speed according to the
subjects brightness.
V-PHASE Adjustment
When using two cameras or more, the
image on the monitor may roll vertically
when switching sources. This rolling
can be minimized by adjusting this
controller.
4)
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 2
1
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
36
45 78

4
NOTES OF USE
DC IRIS LEVEL Adjustment
If using a DC type auto-iris lens, you
will need to set the LEVEL volume.
Turn counterclockwise (L) for a darker
picture. Turn clockwise (H) for a
brighter picture.
Back-Focus Adjustment :
a. Back Focus Screw :
Loosen this screw before using the
Focus Adjustment and to maintain
correct focus afterwards ensure it is
tightened.
5)
6)
b. Focus Adjustment :
Adjust this dial to obtain correct
back-focus whilst using a CS mount
lens.
Menu / Set-up Buttons :
For menu access and adjustment.
Video Output Terminal (BNC) :
Used to give out the video signal.
Connected to the video input terminal
of a monitor, switcher, etc. (to be
terminated with 75 ohm impedance).
6. PUSH BUTTONS AND THEIR FUNCTIONS
Switch Name
Function / Adjustment select (UP)
Main Function
Menu access, function select
Function / Adjustment select (DOWN)
Continue to press more than 2 seconds
to access SUB MENU
Select
All dimensions by mm
Bottom Rear
Front
Side
Top
260V
AC90~
Rear
AC24V
DC12V/

5
SETUP PROCEDURES
7. SETTING MENU
MENU
GAIN
SYNC
GAMMA
BLC
WHITE BAL
APERTURE
PREDTMSP
STD
SHUTTER AUTO 1/50(PAL);1/60(NTSC)
1/2501/5001/10K 1/4K 1/2K 1/1K
D/N MODE AUTO B.C.GMANUAL
D/N LEVEL HIGH LOW
D/N FIL ON OFF
WIDE
INT LL
0.45 1
OFF BLC1 BLC2 BLC3 BLC4
ATW1 ATW2 AWC R:0~6 B:0~63
HIGH LOW MID
ID.
ID POS
NEXT/BACK
OFF TOP BOTTO
EXIT CANCEL DEFAULT
Default Setting
1/120(PAL);1/100(NTSC)
OFF 1/50(PAL);1/60(NTSC)
1/2501/500
1/10K 1/4K 1/2K 1/1K
1/120(PAL);1/100(NTSC)
WITH IR LAMP NO YES

6
SETUP PROCEDURES
8. SUB MENU
Press and hold the ↑button on the side of the camera body for about 2 seconds until the
menu appears on the monitor. The blinking area represents the option to be set.
Note :
All of functions in SUB MENU are used for connection with remote control box (Optional)
or PC Software.
SUB
MENU
001 199
Default Setting
ADDRESS
PELCO P PELCO D
PROTOCOL
1200
BIT RATE 2400 4800 9600
SOFT VER
EXIT DEFAULT
ERNITEC
LANGUAGE ENGLISH FRANCAIS GERMAN
9. OSD FUNCTION DESCRIPTION
SETTING MENU
D/N MODE :
AUTO : When set to this mode, the
camera will change to COLOUR mode
and B/W mode automatically according
to a subject's brightness.
MANUAL : When set to this mode, the
camera will remain in COLOUR or B/W
mode by MANUAL selection.
B.C.G : When set to this mode, the
camera will change to COLOUR mode
and B/W mode manually according to
a RJ-45 B,C,G commands.
1)
D/N LEVEL :
Set up a switch-over point from B/W
mode to COLOUR mode. Use the
SELECT button to select HIGH or LOW
Under the AUTO mode, the switchover
point of brightness from COLOUR
mode to B/W is 1.5 lux.
LOW : The switchover point of
brightness from B/W to COLOUR mode
is 4.5 lux.
HIGH : The switchover point of
brightness from B/W to COLOUR
mode is 7.5 lux.
( To switch between Colour mode and
B/W mode withina short time, use this
setup.)
2)

7
SETUP PROCEDURES
D/N FIL :
ON : Y-signal filter of CCD output is
narrow in B/W mode. In this position,
the horizontal resoulation is 480TV
lines.
OFF : Y-signal filter of CCD output is
wide in B/W mode. In this position, the
horizontal resoulation is 600TV lines.
(If there is horizontal noise in B/W
mode,set to ON)
SHUTTER :
Selection of shutter speed from AUTO
to 1/10K. Sequentially contains AUTO,
1/50(PAL) or 1/60(NTSC), 1/120(PAL)
or 1/100(NTSC) , 1/250, 1/500, 1/1K,
1/2K, 1/4K, 1/10K.
When the slide switch is set to :
AES Mode : Shutter will be able to
select from AUTO to 1/10K.
DC/VIDEO Mode : Shutter will be able
to select from 1/50(PAL) or 1/60(NTSC)
to 1/10K.
GAIN :
STD :Standard position, GAIN=22dB.
WIDE :High-sensitivity position,
GAIN=30dB.
SYNC :
INT : The camera is in the internal
SYNC mode.
LL : The camera is in the LineLock
Mode.Adjusting degrees by V-PHASE
control on the side panel.
GAMMA :
Selection of GAMMA curvature for
GAMMA correction. 0.45 and 1 are
able to select.
BLC :
Selection of backlight compensation
mode.
OFF : The BLC function is off.
Backlight compensation window is like
3)
4)
5)
6)
7)
8)
BLC1 BLC2
(Bottom-Centre Window) (Centre Window)
BLC3
(Bottom Window) (Top Window)
BLC4
WHITE BAL :
ATW1(INDOOR) :
TTL auto trace white balance algorithm
is designed to implement a perfect
colour reproduction. Colour temperature
range is 2600oK~6000oK.
ATW2(OUTDOOR) :
TTL auto trace white balance algorithm
is designed to implement a perfect
colour reproduction. Colour temperature
range is 2500oK~9500oK.
The white balance is automatically
adjusted, within 3 seconds, to
the correct colour temperature of the
environment.
MANUAL :
Manually adjust the R and B (red&blue)
values.
APERTURE :
Selection of picture sharpness (HIGH,
LOW, MID).
PREDTMSP :
(Pre-determined shutter speed)
Preset of shutter speed. When external
controler active this functon, shutter
speed will be change to preset value.
(Manually according to a RJ-45
PREDTMSP command.)
9)
10)
11)

8
ID. :
16 characters Max. (alpha-numeric).
Using to name each camera.
ID POS :
OFF : No ID display.
TOP : Display the ID in the top left of
screen.
WITH IR LAMP
Use enter to get into the submenu.
Using LEFT/RIGHT button, to choose
YES or NO.
*When the environment with extra IR
lights, the ICR filter may hunt
continually. If it occurs, turning this
function YES is able to fix this issue.
**The default setting is NO.
NEXT BACK :
Selection of next page and last page.
EXIT :
Save all settings and exit.
12)
13)
14)
15)
16)
SETUP PROCEDURES
CANCEL :
Reset back to original settings.
DEFAULT :
Recall factory settings.
10. SYSTEM EXTENSIONS
10.1 Connection with Remote Control
Box (Optional)
To connect this camera with Remote
Control Box to obtain more function.
(B.C.G Control, PREDTMSP, 4 Alarm-
In, 2 Alarm-Out …etc.)
10.1-1 Camera & Control Box RJ-45 Pin
define :
17)
18)
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 2
1
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
36
45 78
10.1-2 Single Camera Installation :
COA X
CAT 5
PC
RS-232
A
C/DC POWER
ADAPTOR

9
SETUP PROCEDURES
10.1-3 Multi-Camera Installation :
SYSTEM
MA TRIX
RS- 485
RS- 232
PC
CA M001
CA M199
CA M002
A
C/DC POWER
ADAPTOR
10.2 Connection with Switcher Box (Optional)
To connect this camera with Switcher Box to obtain simple control function.
(B.C.G Control and PREDTMSP)
Rear
ON
OFF
B/W
AUTO
C/L
MODE PREDTMSP

10
SETUP PROCEDURES
10.3 B.C.G & PREDTMSP Control
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V)
2
1
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
36
45 78
B.C.G function :
When D/N MODE set to B.C.G mode, the
camera will change to COLOUR MODE and
B/W MODE manually according to a RJ-45
B.C.G commands.
Control Terminal Image
B = Pin 6 C = Pin 4 G = Pin 5
H
(
OFF
)
H
(
OFF
)
GND Auto
L
(
ON
)
L
(
ON
)
GND
H
(
OFF
)
L
(
ON
)
GND Colour
L
(
ON
)
H
(
OFF
)
GND Black and White
PDSP(PREDTMSP, Pre-determined Shutter
Speed) function :
According to a RJ-45 PDSP commands,
the shutter speed will manually change to
Pre-determined shutter speed which is set
in OSD menu.
Control Terminal PREDTMSP
Pin 3 Pin 7
H
(
OFF
)
GND OFF
L
(
ON
)
GND ON
Note :SW1&SW2 symbolise electronic switching (PIR) or manual
switching (Voltage free contact).
10.4 Conection with PC (Optional)
RS-232
Converter
RS-485
PC
To connect this camera with PC and control
it by PC software RS-232. This converter
is not a standard or optional accessory, but
it's easy to obtain in the market conditions.

11
SPECIFICATIONS
Signal system
Imaging area
Image pickup device
Effective pixels(HxV)
Sync system
Horizontal resolution
Lens mount
Gamma correction
S/N ratio
Iris control
Gain control
White balance
Electric shutter
BLC
Day/Night mode
OSD
Remote control
Video output
Power requirement DC12V /
AC24V AC90~260V
Power consumption
Operating
temperature
Operating humidity
Storage temperature
Weight 500g approx.
Mechanism
Dimensions(WxHxD)
66mm x 55mm x 130mm
(2.6" x 2.16" x 5.11")
Environment
-10º C ~ 50º C
30% ~ 90% RH
-20º C ~ 60º C
1Vpp composite output, 75 ohm
Power supply
DC12V / AC24V
10W (max.)
BLC1 / BLC2 / BLC3/ BLC4 / off
Auto / manual
Yes
RS485, (RJ45)
Video / DC driver
Auto(standard / wide)
ATW1 / ATW2 / ATW3 / AWC / manual
Auto 1/60(1/50) to 1/100,000sec. / manual
Minimum illumination
Day mode: 0.004 lux(F1.4, AGC on, 10 IRE)
Night mode: 0.0012 lux(F1.4, AGC on, 10 IRE)
More than 50dB (AGC off)
Internal / linelock
540 TV lines
CS with backfocus
0.45
Scanning system
2:1 Interlace V: 59.94Hz, 2:1 Interlace V: 50Hz,
H: 15.734KHz H: 15.625KHz
1/2"-type exview CCD
768 x 494 752 x 582
Electric
NTSC PAL
Image system
4.9mm x 3.7mm