ERNITEC Orion User manual

INSTRUCTION MANUAL Ver 1.0 (3810-0132D)
Indoor Mini Speed Dome Camera Series
www.ernitec.com

Indoor Mini Speed Dome Camera
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments/Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause
hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly installed
product may fall, causing serious injury to a child or adult, and damage to the product. Use only with a mounting
device recommended by the manufacturer, or sold with the product. To insure proper mounting, follow the
manufacturer's instructions and use only mounting accessories recommended by manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
2
www.ernitec.com

Indoor Mini Speed Dome Camera
NOTICE
Precautions
■Operating
zBefore using, make sure power supply and others are properly connected.
zWhile operating, if any abnormal condition or malfunction is observed, stop using the camera immediately
and then contact your local dealer.
■Handling
zDo not disassemble or tamper with parts inside the camera.
zDo not drop or subject the camera to shock and vibration as this can damage camera.
zCare must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
■Installation and Storage
zDo not install the camera in areas of extreme temperature, which exceed the allowable range.
zAvoid installing in humid or dusty places.
zAvoid installing in places where radiation is present.
zAvoid installing in places where there are strong magnetic fields and electric signals.
zAvoid installing in places where the camera would be subject to strong vibrations.
zNever expose the camera to rain and water.
1. Introduction
Features 5
Product & Accessories ……………………….………………………………………………………………………. 7
Parts Name & Functions ..…………………….……………………………………………………………………… 8
2. Installation
DIP Switch Setup ……………………………………………………………………………………………………… 9
Direct Installation on the Ceiling …………………………………………………………………………………… 11
Installation using Pendant Mount Bracket .....…………………………………………………………………….. 12
Installation using Wall Mount Bracket ……………………………………………………………………………… 13
Cabling ………………………………………………………………………………………………………………… 15
3. Operation
Check points before Operation …………………………………………………………………………………….. 18
Preset and Pattern Function Pre-Check …………………………………………………………………………… 18
Starting OSD Menu …………………………………………………………………………………………………… 19
Reserved Preset ………………………………………………………………………………………………………. 19
Preset ………………………………………………………………………………………………………………...... 19
Swing ………………………………………………………………………………………………………………...... 20
Pattern ..……………………………………………………………………………………………………………...... 21
Group ………………………………………………………………………………………………………………...... 22
3
www.ernitec.com

Indoor Mini Speed Dome Camera
CONTENTS
Other Functions …..………………………………………………………………………………………………...... 23
OSD Display of Main Screen ……………………………………………………………………………………...... 24
4. Menu
General Rules of Key operation for Menu .……………………………………………………………………...... 25
Main Menu ………………………………….……………………………………………………………………....... 25
Display Setup .……………………………….……………………………………………………………………...... 26
Privacy Zone Mask Setup .................…….……………………………………………………………………...... 27
Zoom Camera Setup .……………………….……………………………………………………………………...... 28
Motion Setup .……………………………….……………………………………………………………………...... 30
Preset Setup 32
Swing Setup ………………………………….……………………………………………………………………...... 34
Pattern Setup .……………………………….……………………………………………………………………....... 35
Group Setup ..……………………………….……………………………………………………………………....... 36
System Initialize …………………………….……………………………………………………………………....... 38
5. Specifications
x10 Zoom Model ..............………………….……………………………………………………………………...... 39
Dimension ..………………………………….……………………………………………………………………...... 40
Features
Camera Specifications
zCCD Sensor : 1/4" Interline Transfer CCD
zZoom Magnification : x10 Optical Zoom, x10 Digital Zoom (Max. ×100 Zoom) Æx10 Zoom Model
zDay & Night Function
zVarious Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.
zIndependent & Simultaneous Camera Characteristic Setup in Preset operation
Powerful Pan/Tilt Functions
zMax. 360°/sec high speed Pan/Tilt Motion
zUsing Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result, time to
target view is reduced dramatically and the video on the monitor is very natural to watch.
zFor jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy to locate
camera to desired target view. Additionally it is easy to move camera to a desired position with zoom-
proportional pan/tilt movement.
4
www.ernitec.com

Indoor Mini Speed Dome Camera
1. INTRODUCTION
Preset, Pattern, Swing, Group, Privacy Mask and More…
zMax. 127 Presets are assignable and characteristics of each preset can be set up independently, such as
White Balance, Auto Exposure, Label and so on.
zMax. 8 set of Swing action can be stored. This enables to move camera repetitively between two preset
positions with designated speed.
zMax. 4 of Patterns can be recorded and played back. This enables to move camera to follow any trajectory
operated by joystick as closely as possible.
zMax. 8 set of Group action can be stored. This enables to move camera repetitively with combination of
Preset or Pattern or Swing. A Group is composed of max. 20 entities of Preset/Pattern/Swings.
zPrivacy Masks are assignable, not to intrude on other’s privacy. (4 Privacy Zones)
PTZ(Pan/Tilt/Zoom) Control
zWith RS-485 communication, max. 255 of cameras can be controlled at the same time.
zPelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.
OSD(On Screen Display) Menu
zOSD menu is provided to display the status of camera and to configure the functions interactively.
zThe information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be displayed on screen.
Alarm I/O Functions
z4 alarm sensor Inputs are available.
zTo reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo coupler.
zThe signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications.
zIf an external sensor is activated, camera can be set to move to the corresponding Preset position.
Product & Accessories
5
www.ernitec.com

Indoor Mini Speed Dome Camera
1. INTRODUCTION
Product & Accessories
Options
●Pendant Mount Bracket ●Wall Mount Bracket
Parts Name & Functions
6
www.ernitec.com

Indoor Mini Speed Dome Camera
1. INTRODUCTION
zMain Unit / Surface Mount Bracket zBack of Main Unit
zBubble Do not detach protection vinyl from the bubble before finishing all installation
process to protect the bubble from scratches or dust.
zSurface Mount Bracket This is used to install the camera directly on the ceiling. After separating this
cover first and then attach this directly to ceiling. Camera must be assembled at
the last stage.
zFixing Screw Fixes main unit to surface mount bracket.
zCabling Terminal Block During installation, Power, Video, Communication, Alarm Input cables are
connected on to this cabling terminal block.
zDIP Switch Adjusts camera ID and protocols.
DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID, communication protocol.
7
www.ernitec.com

Indoor Mini Speed Dome Camera
2. INSTALLATION
Camera ID Setup
zID number of camera is set using dip switch. The example is shown
bellow.
Pin 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
ex) ID=5 on off on off off off off off
ex) ID=10 off on off on off off off off
Do not use 0 as camera IDzThe range of ID is 1~255. . Factory default of
Camera ID is 1.
zIf you want to control a certain camera, you must match the camera ID
with Cam ID setting of DVR or Controller.
Communication Protocol Setup
8
www.ernitec.com

Indoor Mini Speed Dome Camera
2. INSTALLAT2. INSTALLATIONION
zSelect the appropriate Protocol with DIP switch combination.
Switch State
P0
(Pin 1)
Protocol
P3
P1
(Pin 2) (Pin 3)
OFF OFF OFF PELCO-D, 2400 bps
ON OFF OFF PELCO-D, 9600 bps
OFF ON OFF PELCO-P, 4800 bps
ON ON 0FF PELCO-P, 9600 bps
Others Reserved
zIf you want to control using DVR or P/T controller, their protocol must be
identical to camera. Otherwise, you can not control the camera.
zIf you changed camera protocol by changing DIP S/W, the change will be
effective after you reboot the camera.
zFactory default of protocol is “Pelco-D, 2400 bps”.
Termination Switch Setting
Termination switch(Pin 4) is used in cases listed below.
zLong-distance communication between the controller and the camera
(1-to-1 connection)
When the connecting distance between the two units is especially long,
communication errors may occur due to the impedance of transmission
cable. In this case, set the termination switch of both units to ON.
zControlling multiple cameras (Multiple connection)
The camera may not operate correctly if multiple cameras are connected
and controlled. In this case, set the termination switch of the controller and
the last connected camera to ON and the switch of other cameras is OFF.
Ex) Using the Terminating Resistance
Direct Installation on the Ceiling
9
www.ernitec.com

Indoor Mini Speed Dome Camera
①To pass cables to upside of ceiling, please, make about
50~60mm hole on the ceiling panel.
②Detach the marked part from the rubber gasket and
srew the surface mount bracket to the ceiling with
fixing screws.
You can use “Guide Pattern” for
the making holes.
③Wire cables to terminal block and connect the terminal
blocks to main unit.
④Insert the main body into the surface mount bracket
with the molding lines on each part being aligned
and turning clockwise.
⑤Insert the fixing screw tightly and detach the protection
vinyl from dome cover.
Installation using Pendant Mount Bracket
10
www.ernitec.com

Indoor Mini Speed Dome Camera
2. INSTALLATION
①Screw pendant mount to ceiling with screws. ②Detach the marked part from the rubber gasket and
screw the mounting base to the pendant mount
bracket with fixing screws.
You can use “Guide Pattern” for
the making holes.
③Wire cables to terminal block and connect the terminal
blocks to main unit.
④Insert the main body into the pendant mount bracket
with the molding lines on each part being aligned
and turning clockwise.
11
www.ernitec.com

Indoor Mini Speed Dome Camera
2. INSTALLATION
⑤Insert the fixing screw tightly and detach the
protection vinyl from dome cover.
Installation using Wall Mount Bracket
①Screw wall mount bracket to wall with 3 screws. ②Detach the marked part from the rubber gasket and
srew the mounting base to the wall mount bracket with
fixing screws.
You can use “Guide Pattern" for
the
12
www.ernitec.com

Indoor Mini Speed Dome Camera
2. INSTALLATION2. INSTALLATION
③Wire cables to terminal block and connect the terminal
blocks to main unit.
④Insert the main body into the wall mount bracket with
the molding lines on each part being aligned and
turning clockwise.
⑤Insert the fixing screw tightly and detach the protection
vinyl from dome cover.
Cabling
13
www.ernitec.com

Indoor Mini Speed Dome Camera
Power Connection
zPlease, check the voltage and current capacity of rated power carefully. Rated power is indicated in the back
of main unit.
Rated Power Input Voltage Range Current Consumption
DC 12V DC 11V ~ 18V 1 A
AC 24V AC 17V ~ 29V 0.8 A
RS-485 Communication
zFor PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time, RS-
485 communication lines of them is connected in parallel as shown below.
14
www.ernitec.com

Indoor Mini Speed Dome Camera
2. INSTALLATION
Audio Input/Output Connection (Reserved for network model)
zConnection with audio input/output device.
Video Connection
zConnect with BNC coaxial cable
Network Connection (Reserved for network model)
Notice) Network model is now preparing.
zNETWORK 1
Connect with LAN cable.
If LAN cable is not connected properly, This product can not be operate.
zNETWORK 2 (Reserved for supplier.)
DO NOT CONNECTED ANY DEVICE.
15
www.ernitec.com

Indoor Mini Speed Dome Camera
2. INSTALLATION
Alarm Input Connection
zSensor Input
IN COM+
Internal +5V~12V
IN 1-
IN 4-
Sensor 1 Output
+
+
-
-
+
-
Sensor 4 Output
Before connecting sensors, check driving voltage and output signal type of the sensor. Since output signal types of
the sensors are divided into Open Collector and Voltage Output type in general, the cabling must be done properly
after considering these typed.
Signal Description
IN COM+ Connect (+) cable of electric power source for Sensors to this port as
shown in the circuit above.
IN1-, IN2-, IN3-, IN4- Connect output of sensors for each port as shown in the circuit above.
If you want to use Alarm Input, the types of sensor must be selected in OSD menu. The sensor types are Normal
Open and Normal. If sensor type is not selected properly, the alarm can be activated reversely.
Normal Open Output Voltage is high state when sensor is activated
Normal Close Output Voltage is high state when sensor is not activated
16
www.ernitec.com

Indoor Mini Speed Dome Camera
3. OPERATION
Check points before operation
zBefore power is applied, please check the cables carefully.
zThe camera ID of the controller must be identical to that of the target camera. The camera ID can be checked
by reading DIP switch of the camera.
zIf your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
zIf you changed camera protocol by changing DIP switch, the change will be effective after you reboot the
camera.
zSince the operation method can be different for each controller available, refer to the manual for your controller
if camera can not be controlled properly. The operation of this manual is based on the standard Pelco®
Controller.
Preset and Pattern Function Pre-Check
zCheck how to operate preset and pattern function with controller or DVR in advance to operate camera function
fully when using controller or DVR.
zRefer to the following table when using standard Pelco® protocol controller.
<Go Preset> Input [Preset Number] and press [Preset] button shortly.
Input [Preset Number] and press [Preset] button for more than 2 seconds.
<Set Preset>
<Run Pattern> Input [Pattern Number] and press [Pattern] button shortly.
<Set Pattern> Input [Pattern Number] and press [Pattern] button for more than 2 seconds.
zIf controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more
information, refer to “Reserved Preset” in this manual.
17
www.ernitec.com

Indoor Mini Speed Dome Camera
3. OPERATION
Starting OSD Menu
zFunction Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be
configured for each application.
zEnter Menu <Go Preset> [95]
Reserved Preset
Some Preset numbers are reserved to special functions.zDescription
zFunction <Go Preset> [95] Enters into OSD menu.
<Go Preset> [131~134] Runs Pattern Function 1 ~ 4
<Go Preset> [141~148] Runs Swing Function 1 ~ 8
<Go Preset> [151~158] Runs Group Function 1 ~ 8
Preset
zFunction Max. 127 positions can be stored as Preset position. The Preset number can be assigned
from 1 to 128, but 95 is reserved for starting OSD menu.
Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for
each preset. Label should be blank and "Camera Adjust" should be set to "GLOBAL" as
default. All characteristics can be set up in OSD menu.
zSet Preset <Set Preset> [1~128]
zRun Preset <Go Preset> [1~128]
To delete Preset, use OSD menu.zDelete Preset
18
www.ernitec.com

Indoor Mini Speed Dome Camera
3. OPERATION
Swing
zFunction By using Swing function, you can make camera to move between 2 Preset positions
repeatedly. When swing function runs, camera moves from the preset assigned as the 1st
point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera
moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in
CCW(Counterclockwise) direction.
In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd
point, camera turns on its axis by 360°in CW(Clockwise) direction and then it turns on its
axis by 360°in CCW(Counterclockwise) direction. Speed can be set up from 1°/sec to
180°/sec.
To set Swing, use OSD menu.
zSet Swing
zRun Swing Method 1) <Run Pattern> [Swing NO.+10] ex) Run Swing 3 : <Run Pattern> [13]
Method 2) <Go Preset> [Swing NO + 140] ex) Run Swing 3 : <Go Preset>[143]
To delete Swing, use OSD menu.zDelete Swing
19
www.ernitec.com

Indoor Mini Speed Dome Camera
3. OPERATION
Pattern
zFunction Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of
controller for assigned time and revives the path exactly as it memorized.
4 Patterns are available and Maximum 1200 communication commands can be stored in
a pattern.
Pattern can be created by one of following two methods.
zSet Pattern
Method 1) <Set Pattern> [Pattern NO.]
zPattern editing screen is displayed as bellow.
zMovement by Joystick and preset movement can be memorized in a pattern.
zThe rest memory size is displayed in progress bar.
zTo save the recording, press NEAR key and to cancel, press FAR key.
Method 2) OSD Using OSD Menu: See the section “How to use OSD Menu”.
Method 1) <Run Pattern> [Pattern NO.] ex) Run Pattern 2 : <Run Pattern> [2]
zRun Pattern
Method 2) <Go Preset> [Pattern NO+130] ex) Run Pattern 2 : <Go Preset>[132]
To delete Pattern, use OSD menu.
zDelete Pattern
20
www.ernitec.com