Erone SEL2641R433-OC4 User manual

4 OUTPUT OC RX CARD
1A - Main features
The receiver type SEL2641R433-OC4 is a superheterodyne receiver
operating at 433,92 MHz.
It can be used with the transmitters series 024A Rolling code and MINI.
SEL2641R433-OC4
GETTING
STARTED
It is equipped with a strip-type output connector with standard pitch of
2,54 mm, so it can be used only with compatible devices.
The internal EEPROM memory can store up to 85 transmitter codes.
The outputs have the open-collector configuration.
The transmitter memorization can be carried out with a push-button
It is also available a single antenna input.
Il fabbricante, CDVI Wireless Spa, dichiara che l’apparecchiatura radio
SEL2641R433-OC4 è conforme alla direttiva 2014/53/UE. Il testo
completo della dichiarazione di conformità UE è disponibile al
seguente indirizzo internet: www.erone.com.
USABLE TRANSMITTERS
!Series Erone 024A Type S2TR2641E2: 2 key transmitter
!Series Erone 024A Type S2TR2641E4: 4 key transmitter
!Series Erone 433 MINI Type SETR2641AM2 :2 key mini transmitter
Thank you for choosing this product.
You are recommended to read carefully this manual
before installing the product.
SUMMARY
1A - Main features
1B - Technical specifications
1C - Layout and connections
1 - INTRODUCTION
2 - TRANSMITTER MEMORIZATION
3 - SINGLE TRANSMITTER CANCELLATION
4 - MEMORY ERASURE
5 - MEMORY FULL
1B - Technical specifications
Receiver type Superheterodyne
Carrier frequency 433,92 MHz
Local oscillator frequency 6,6128 MHz
Demodulation AM/ASK
Local Oscillator VCO / PLL
Channel width > 25 KHz
Intermediate frequency 10.7 MHz
Input sensitivity -115 dBm
Local oscillator spurious emissions < -57 dBm
Input load: 50 Ohm
Power supply: 12 Vdc
Consumption: 11 mA
Outputs 4
Output type Open-collector
Max sink current (single output) 500 mA
Max total current (all 4 outputs) 1 A
Memory capacity 85 user codesTX
Security code Rolling code
64
Max code combination number 2
Operating temperature -20°/+80°C
Weight 9 gr
Overall dimensions (mm) 44 x 42 x 8
T H E S M A RT L I V IN G

Manufactured by CDVI Wireless Spa
Via Piave, 23 - 31020
San Pietro di Feletto (TV) - Italy
Tel.: [phone] - Fax.: [phone]
Toll-free number: 800.53.46.46
E-Mail: [email protected] - Web: www.erone.com
IS-ROCERUK Rev. 1 del 13.06.2017
2 - TRANSMITTER MEMORIZATION
1D - Layout and connections
L1 L2 L3 L4 The guarantee period of this products is 24 months, beginning from the
manufacturer date. During this period, if the product does not work
correctly, due to a defective component, the product will be repaired or
substituted at the discretion of the producer. The guarantee does not cover
the plastic container integrity. After-sale service is supplied at the
producer's factory.
GUARANTEE
In case of memory full, that means 85 transmitters are already stored, if
one try to store an extra transmitter, a sequence of 3 blinks of L3 and L4
occurs and the operation fails.
5 - MEMORY FULL
4 - COMPLETE MEMORY ERASURE
Keep the button P1 pressed down until the first red led L1 switches on,
release it, push it again and keep it pushed down until 3 blinks of the red
led L3 and green led L4 occur.
In this way the memory is completely cancelled.
3 - SINGLE TRANSMITTER CANCELLATION
Select the right output to which the transmitter was connected by
pushing P1, as indicated in the previous paragraph. Then push the
key of the transmitter to cancel : L3 and L4 will blink twice to
confirm.
Repeat the same procedure for all the transmitter keys to cancel.
The receiver makes the memorization of the transmitter keys in
sequential way, by using the button P1
Each operation is confirmed by the leds L1, L2, L3, L4.
The led activation is cyclic: at each activation of P1 a led switches on
and the previous switches off.
Keep the button P1 pressed down until the red led L1 switches on,
release P1 and push the key “A” of the transmitter ; after, push again P1,
the second red led L2 switches on , release P1 and push the key “B” of
the transmitter. After a while both the led will switch off and the
procedure will be finished.
In this way the keys “A” and ”B” of the transmitter activate the outputs
OUT1 and OUT2 of the receiver.
The procedure to follow for the keys ”C” and “D” is the same as above.
For the memorization of the “C” key on K3 push P1 3 times, and for the
memorization of the “D” key on K4 push P1 4 times.
For multiple transmitter memorization, first select the right output
position with P1, and then push the keys of all the transmitters you want
L4
L3
L2
L1
P1