Erone SEL2641R433-C5P User manual

4
IS-C5PERUK Rev. 0 del 5/4/201
3
Manufactured by
Via Piave, 23 - I-31020 S.Pietro di Feletto (TV) - ITALY
Tel. [phone] - Fax. [phone]
e-mail: [email protected]
Web: www.erone.com
ELPRO INNOTEK S.p.A.
THE SMART LIVING
P1P1 P1
Keep P1 pressed down for
more 4 sec. until LR3+LV
make 3 long flashes
P1
Keep P1
pressed down
for 2 sec. until
LR1 turns on
Release
P1
LR1
turns on
LR3+LV
3 flashes
GUARANTEE
The guarantee period of this products is 24 months, beginning from the manufacturer date.
During this period, if the product does not work correctly, due to a defective component, the product will be repaired
or substituted at the discretion of the producer. The guarantee does not cover the plastic enclosure integrity.
After-sale service is supplied at the producer's factory.
DIP-SWITCH 1
Set to ON the switch corresponding to the relay to activate,
i.e. -->SW1 = ON, SW2, SW3, SW4 = OFF ONLY Relay 1 activated.
i.e. -->SW1 = ON, SW2 = OFF, SW3 = ON, SW4 = OFF Relays 1, 3 activated simultaneously
DIP-SWITCH 2
ON
OFF
1234
DIP-SWITCH 3
CHANNEL 3 - LED LR3 ( RED )
ON
OFF
1234
DIP-SWITCH 4
CHANNEL 4 - LED LV ( GREEN )
ON
OFF
1234
DIP5-SWITCH 5
RELAY 5 ( COMMON )
The relay 5 can be activated simultaneously with each relay ( 1,2,3 or 4, depending by the
settings of DIP5.
Set to ON the switch corresponding to the channel which activates simultaneously even the
relay 5.
i.e. : sw1, sw2, sw3, sw4 = OFF : relay 5 NEVER ACTIVATED
i.e. : sw1 = ON, sw2, sw3, sw4 = OFF : relay 5 activated by Channel 1
i.e. : sw1 = ON, sw2 = ON, sw3, sw4 = OFF : relay 5 activated by Channel 1 or
Channel 2
12341234
DIP-SWITCH CONFIGURATION
Each dip-switch sets the relay or the relays activated by the corresponding channel.
ON
OFF
CHANNEL 1 - LED LR1 ( RED )
ON
OFF
CHANNEL 2 - LED LR2 ( RED )
FULL MEMORY ERASURE
THE SMART LIVING
1
ERONE 4+1 RELAY RECEIVER SEL2641R433-C5P
INTRODUCTION
The receiver Erone type SEL2641R433-C5P is designed for the control of oleodynamic systems thanks to the 5 output
relays . The main 4 relays gives a C-NO-NC dry contact when the transmission is correctly decoded , the fifth relay can
be activated together to one on them . The memorisation of the transmitter code into the receiver memory can be done
in self-learning mode with one button. The appliance full complies with the European Directives 89/336/EEC,
73/23/EEC and Regulation EN 60950
TECHNICAL SPECIFICATIONS
Receiver type Superheterodyne
Local oscillator frequency 6,6128 MHz
Modulation AM/ASK
Input impedance 50 Ohm
Input sensitivity -115 dBm
Local oscillator emissions < -57 dBm
Power supply
Consumption 270 mA
Relays 4 + 1
Relay operating mode Pulse / Latch
Min applicable power 1A / 6V
User codes max 85
Operating temperature
IP Grade
Weight 400
Overall dimensions (mm ) 110 x 110 x 60
Selflearning radio memorisation yes
Carrier frequency 433.92 MHz
12 / 24 Vdc
Max applicable power 20A / 27V - max 300W
Outputs relays C - NC - NO
Security protocol Keeloq hopping code
-20°/+70°C
IP56
gr.

2
THE SMART LIVING
JP2 = ON
R2 LATCH
JP1=OFF
R2 PULSE
121110
R3
2019
987 181716
151413
R4 R5
0
12 Vdc
24 Vdc
P1
R3 R4 R5
JP2
LAYOUT
LR3
LV
654
R1
321
R2
R1 R2
C
NC
NO
C
NC
NO
C
NC
NO
C
NC
NO
C
NC
NO
ON
OFF
12341234123412 34
DIP1DIP1 DIP2 DIP3 DIP4
LR1 LR2
1234
DIP5
Declaration of Conformity:
Elpro Innotek Spa as manufacturer declares that the
following appliances : SEL39R433-C3P, fullfills the
requirements of the European Directives 73/23/CEE,
89/336/CEE and 99/05/CE.
Security measures
For a perfect functioning of the device, read carefully this
manual and follow all the indications, since an inadeguate
use can make damages to the device
??
( * ) Connect a 17 cm piece of wire at terminal 19 or a 433 MHz tuned antenna with cable RG58 ( 50 Ohm )
Antenna (*)
3
THE SMART LIVING
MEMORIZING
Each button of the transmitter can be memorized
on one or more channels of the receiver.
The memorisation can be done in self-learning by
pressing P1.
Press P1 sequentially to select the channel desired.
2019
P1
Jp1
Jp2
LR3
LV
ON
OFF
1234123412 341234
DIP1DIP1 DIP2 DIP3 DIP4
LR1 LR2
P1
Keep P1
pressed down
for 2 sec. until
LR turns on
Release
P1
Press the
transmitter button
to memorize
P1
LR1
turns on
LR1
makes a flash and stays on again for
more 5 sec. then turns off
EXAMPLE 1
MEMORIZING ON
CHANNEL LR1
LR1 LR2 LR3 LV
P1
Keep P1
pressed down
for 2 sec. until
LR turns on
Release P1 or, if the transmitter is
memorised on channels 2,3 or 4
press P1 again until the led
corresponding to the channel where the
transmitter button has been memorised,
turns ON
Press the
transmitter button
to memorize
P1
LR1
turns on the 2 leds LR1 or LR2 or
LR3 and LV
make 2 flashes then turn off.
The procedure ends.
For deleting more
transmitter buttons, repeate
the complete procedure
EXAMPLE 2
MEMORIZING ON
CHANNEL LV
P1
TRANSMITTER CANCELLING
LRx LV
P1
Keep P1
pressed down
for 2 sec. until
LR turns on
Press P1 3 more times
until LV turns ON
Press the
transmitter button
to memorize
P1
LR1
turns on
LR1
makes a flash and stays on again for
more 5 sec. then turns off