Erone SEL128R433-NN User manual

Receiver type Superheterodyne
Carrier frequency 433,92 MHz
Demodulation GFSK
Local Oscillator VCO / PLL
Input sensitivity -115 dBm
Local oscillator spurious emissions < -57 dBm
Input load: 50 Ohm
Power supply: 12 / 24 Vac/dc
Max applicable power 24VA
Current consumption : at rest 9 mA ( @12V or 24V)
with relay excited 26 mA @ 12V
31 mA @ 24V
Relay number 1
Operating modes Pulse / Delayed
Release delay 1 - 30 Sec.
Contacts C-NO
Memory capacity 248 user codes
TX security code Rolling code
128
Max code combination number 2
Operating temperature -20°/+70°C
Housing protection IP2X
Overall dimensions (mm) 50 x 32 x 20
2 - TECHNICAL SPECIFICATIONS
ERONE 1 RELAY NANO RECEIVER 128 BIT
1 - DESCRIPTION
Thank you for choosing this product.
You are recommended to read carefully this manual before
installing the product.
1A - Introduction
The receiver type SEL128R433-NN is , designed to control
automatic closing systems and anti-burglar systems, thanks to its
very high security coding system.
The operating frequency is among the European harmonised
frequencies; the product fully complies with the EMC European
Regulations (CE).
The code sent by the transmitter changes at every activation,
avoiding any scanning and copying risk.
A special algorithm allows to keep synchronized transmitter and
receiver.
The receiver has 1 output relay ( with NO contacts, and can be
connected to many types of mechanics ( gate, garage door, rolling
shutters, awnings, anti-burglar appliances, lighting, etc.).
All the receivers of the range can store into the EEPROM a serial
number, a manufacturer key and a synchronism algorithm of more
transmitters.
The programming can be done in self-learning mode by means of
one button.
The housing protection allows indoor installations.
The appliance full complies with the European Directive
2014/53/UE «Red» and the Standard and FCC Part 15.
38,7
50
32
Dimensions
3
3 - LAYOUT AND CONNECTIONS
J1 = CLOSED
MEMO without P1
ENABLED ( 5.2)
MEMO SELECTION
INSTALLATION MANUAL
SEL128R433-NN
Fig. 1
P1
J1
RELAY
K1
BUZZER
+
-
C
NO
ANTENNA see
Memo selection
4 - OPERATING MODES & DELAY
The relay can operate in PULSE or DELAYED mode. The default
pulse is 1 sec. In delayed mode the release of the relay occurs after
a programmable delay ( 1 - 30 Sec. ) see next paragraph.
During the delay time the reception of a further signal from the
transmitter releases the relay.
J1 = OPEN
MEMO without P1
DISABLED (5.2)
- The equipment must be powered from a device that
provides a safety extra low voltage (SELV) type LPS
( Low Power Source);
- There must be a suitable disconnecting device to the
current drawn by the receiver (90 mA max @ 12Vdc).
!
Power Input
12 - 24 Vac/dc
self-adjusting

Bip
A+B ABip A or B
5 Sec. Bip
Fig. 5
5 - TRANSMITTERS MEMORIZATION
Bip A
Fig. 4
P1
Bip
5 Sec.
Bip
6 .
If the memory is full, when you try to memorize a new transmitter the buzzer does 3 bip.
Memory full
7 .
7.1 Single transmitter
1) Push P1 until the bip of the buzzer, then release it.
2) Push the key of the transmitter to delete until the bip of the buzzer.
7.2 Full Memory erasure
1) Push P1 until the bip of the buzzer, then release it;
2) Release P1 and push it again until the buzzer does 3 bip: at this point the memory has been completely erased.
Memory erasure
Bip
A+B BBip
Fig. 6
P1
2 Sec.
1 Sec.
Procedure
1) Keep pushed the button P1 for 4 sec. until the
buzzer makes one bip ( Fig. 3);
At this point it’s possible to set a release delay for the
relay different from 1 Sec. ( by default ): press P1
many times as are the seconds of the delay desired.
( max 30 Sec.).
5 sec. after the last pulse given, the buzzer makes a
bip and the procedure ends.
Bip
Fig. 3
5 Sec.
Bip
P1
Bip
N Sec.(max 30)
P1
Bip
5.1 Using P1
1) Keep P1 pressed down until the buzzer BUZ emits a
short bip ( Fig. 3);
2) Push the key of the transmitter to memorize and
verify the bip of the receiver;
3) At this point the receiver waits for more transmitters
: 5 seconds after the last transmitter memorized the
receiver makes a bip and the procedure ends.
5.2 Without P1
With this procedure it is possible to memorize the
transmitters without accessing to P1 ( Fig. 4).
1) Push simultaneously the keys A + B of the
transmitter until the bip;
2) Release and then keep pushed the key A until the
next bip of the buzzer ( memory opening );
3) Release A and push the key of the transmitter to memorize ( A or B ) until the bip of the buzzer ( memory closing).
NOTE :The memorization of a new transmitter can be done only by using a transmitter already memorized.
Use the transmitter already memorized to open the memory ( step 1 and 2 ).
Complete the procedure by pressing the key of the new transmitter to memorize.
It’s possible to program the receiver to make a bip at each
relay activation.
Follow the procedure below.
1) Press simultaneously the keys A+B of a transmitter already
memorised.
2) Release and press the key B of the transmitter up to the bip.
For the bip disabling repeat the above procedure
8. Enabling/disabling the activation bip ( Fig. 6)
IS-RNN128ERUK Rev. 1 del 22/4/2020
Manufactured by CDVI Wireless S.p.A.
Via Piave, 23
31020 S.Pietro di Feletto (TV)
Tel: [phone] - Fax: [phone]
Internet: www.erone.com - E-mail: [email protected]
T H E S M A R T L I V I N G
WARRANTY
The warranty period of this product receivers is 24 months, beginning from
the manufacturing date. During this period, if the product doesn’t operate
correctly, due to a defective component, the product will be repaired or
replaced at the sole discretion of the producer. The warranty does not
extend to the receiver case which can be damaged by conditions outside the
control of the producer.