Escea DF Series Installation and maintenance instructions

Installation / Service Instructions
For the latest documentation, visit www.escea.com
DF / DFS -Series
630381_13
Gas Fireplace

Important:
The appliance shall be installed in accordance with;
• This installation instruction booklet
• Local gas fitting regulations
• Municipal building codes
• Electrical wiring regulations
• Any other relevant statutory regulations.
• AS/NZS 5601.1:2013 Gas Installations
WARNING:
This appliance must be installed by a qualified person.
Do not modify this appliance.
This appliance is not intended for use by young children or infirm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
Failure to follow these instructions could cause a malfunction of the heater, which could result in
death, serious bodily injury, and/or property damage. Failure to follow these instructions may also
void your fire insurance and/or warranty.
Who can install this product:
Installation must be carried out by a registered installer who, on completion of the installation, must
issue a:
AUS: Certificate of Compliance
NZ: Certificates that comply with the latest legislation in accordance with national and/or local
codes. If these are not issued then the Escea warranty may be void.
Warranty Repair and Annual Servicing:
Please contact Escea if you require warranty work. Warranty repair work must be carried out by a
recognised gas fire technician. It is recommended that recognised Escea Gas Fire Technicians are
also used to carry out annual servicing requirements (particularly during the warranty period). For
contact details of recognised Escea Gas Fire Technicians in your area, or for replacement parts,
please contact the retailer from whom the appliance was purchased our visit our website.
The heater must be installed according to these instructions and in compliance with all relevant
building, gas fitting, electrical and other statutory regulations (eg. AS/NZS 5601). Any shortcomings
in the appliance and flue installation will be the responsibility of the installer, and Escea will not be
accountable for any such failings or their consequences.
Manufactured by: Escea Ltd, PO Box 5277 Dunedin NZ, Ph: [phone].
For contact details of your local Escea distributor or dealer in New Zealand, please
visit: www.escea.com or email: [email protected]. From Australia, please visit www.escea.com.au,
call AU: 1800 460 832 or WA: 1800 730 140, or email us at [email protected]

DF700 PRODUCT SPECIFICATION
MODEL NAME DF700
Description of Appliance Powerflued Gas Fire Heater
Star Rating 4-5 Stars
Max. Heat Output 5.9kW
A/NZ Approval No. AS/NZS 5263.1.3
Gas Type Natural Propane ULPG
Gas input High 25 MJ/hr 25 MJ/hr 24 MJ/hr
Low 11 MJ/hr 11 MJ/hr 9.5 MJ/hr
Inlet Pressure Max 5.0 kPa 5.0 kPa 5.0 kPa
Min 1.13 kPa 2.75 kPa 2.75 kPa
Operating Pressure on High 1.0 kPa 2.30 kPa 2.30 kPa
Operating Pressure @ Front Burner Jet on High 0.95 kPa 2.29 kPa 2.29 kPa
Burner Jet Size Front: 1.70mm
Rear:1.40mm
Front: 1.05mm
Rear:0.9mm
Front: 1.05mm
Rear:0.85mm
Aeration Collar Hole Size 1 hole @ Ø3.5mm No Collars No Collars
Pilot injector #42 #27 #27
Appliance Dimensions (mm)
Width 693.0 mm
Height 596.0 mm
Depth 387.0 mm
Weight Kg 45 kg
Ignition System Electronic Ignition to pilot system
Escea PCB
Ignition Activation 7 secs (approx)
Flame Safeguard Flame Rectification
Consumption 84W @ 0.35A 230V
Remote controls Yes
Timers Yes
Clock Yes
Function lock / child Yes
Temperature control Yes
Connections
Electric 230V AC
Gas 1/2" BSPP female lower right of fireplace chassis
Flue Type 4” and 3” Flexi Flue
Spigot
Location Rear and centre
Data badge location On Chassis Base

DF960 PRODUCT SPECIFICATION
MODEL NAME DF960
Description of Appliance Powerflued Gas Fire Heater
Star Rating 4.4-4.9 Stars
Max. Heat Output 7.7kW
A/NZ Approval No. AS/NZS 5263.1.3
Gas Type Natural Propane ULPG
Gas input High 31 MJ/hr 31 MJ/hr 28 MJ/hr
Low 15 MJ/hr 14 MJ/hr 12 MJ/hr
Inlet Pressure Max 5.0 kPa 5.0 kPa 5.0 kPa
Min 1.13 kPa 2.75 kPa 2.75 kPa
Operating Pressure on High 1.0 kPa 2.30 kPa 2.30 kPa
Operating Pressure @ Front Burner Jet on High 0.94 kPa 2.20 kPa 2.20kPa
Burner Jet Size Front: 1.85mm
Rear: 1.70mm
Front: 1.20mm
Rear: 1.05mm
Front: 1.10mm
Rear: 1.02mm
Aeration Collar Hole Size for Logs & Embers/
Flakes 1 holes @ Ø4mm No Collars No Collars
Aeration Collar Hole Size for Coals 1 hole @ Ø2.5mm No Collars No Collars
Pilot injector #42 #27 #27
Appliance Dimensions (mm)
Width 943.0 mm
Height 596.0 mm
Depth 402.0 mm
Weight Kg 70 kg
Ignition System Electronic Ignition to pilot system
Escea PCB
Ignition Activation 7 secs (approx)
Flame Safeguard Flame Rectification
Consumption 84W @ 0.35A 230V
Remote controls Yes
Timers Yes
Clock Yes
Function lock / child Yes
Temperature control Yes
Connections
Electric 230V AC
Gas 1/2" BSPP female lower right of fireplace chassis
Flue Type 4” and 3” Flexi Flue
Spigot
Location Rear and centre
Data badge location On Chassis Base

DF990 PRODUCT SPECIFICATION
MODEL NAME DF990
Description of Appliance Powerflued Gas Fire Heater
Star Rating 4.9 stars
Max. Heat Output 8.2kW
A/NZ Approval No. AS/NZS 5263.1.3
Gas Type Natural Propane ULPG
Gas input High 35 MJ/hr 30 MJ/hr 30 MJ/hr
Low 16 MJ/hr 12 MJ/hr 12 MJ/hr
Inlet Pressure Max 5.0 kPa 5.0 kPa 5.0 kPa
Min 1.13 kPa 2.75 kPa 2.75 kPa
Operating Pressure on High 1.0 kPa 2.3 kPa 2.3 kPa
Operating Pressure @ Front Burner Jet on High 0.94 kPa 2.2 kPa 2.2 kPa
Burner Jet Size Front: 2.1mm
Rear: 1.8mm
Front: 1.2mm
Rear: 1.02mm
Front: 1.2mm
Rear: 1.02mm
Aeration Collar Hole Size for Logs & Embers/
Flakes
2 holes @
Ø7.5mm
Spacer (no
restriction)
Spacer (no
restriction)
Aeration Collar Hole Size for Coals 2 holes @
Ø7.5mm
Spacer (no
restriction)
Spacer (no
restriction)
Pilot injector #42 #27 #27
Appliance Dimensions (mm)
Width 943.0 mm
Height 884.0 mm
Depth 402.0 mm
Weight Kg 90 kg
Ignition System Electronic Ignition to pilot system
Escea PCB
Ignition Activation 7 secs (approx)
Flame Safeguard Flame Rectification
Consumption 84W @ 0.35A 230V
Remote controls Yes
Timers Yes
Clock Yes
Function lock / child Yes
Temperature control Yes
Connections
Electric 230V AC
Gas 1/2" BSPP female lower right of fireplace chassis
Flue Type 4” and 3” Flexi Flue
Spigot
Location Rear and centre
Data badge location On Chassis Base

A Product Description and Installation Process 8
A1 Product Description 8
A2 Recommended Install Process 8
A3 Product Dimensions 9
B Creating the Cavity 10
B1 Cavity Shape 10
B2 Floor Clearances 11
B3 Corner Installations 12
B4 Hearth 12
B5 Cavity Base 12
B6 Wall Linings 12
B7 Television & Mantel Clearances 13
B8 Fascia Dimensions 14
C Installing the Flue 16
C1 Flue Configuration (If less than 4m flue length is required) 16
C2 Flue Configuration (If more than 4m flue length is required) 18
C3 Masonry Vertical Power Flue Kit (up to 6m) 19
C4 Masonry Vertical Power Flue Extension Kit (6 to 12m) 20
C5 Installing the Horizontal Power Flue 21
C6 Installing the Universal Vertical Power Flue (Internal Install) 24
C7 Installing the External Vertical Power Flue (UVP) 26
C8 Installing in Accordance with Relevant Codes 27
C9 Running the Flue 28
C10 Insulation Specification and Installation 29
C11 Running the Power Flue Electrical Cable 29
C12 Setting up the Flue Spigot Plate 30
D Installing the Electricity and Gas to the Appliance 31
D1 Power Supply 31
D2 Removing the Glass 31
D3 Removing the Burners 32
D4 Gas Pipe Sizing 33
D5 Gas Pipe Position 33
E Installing The Appliance 34
E1 Installation 34
E2 Connecting the Flue 34
E3 Removing the Burner Tray 35
E4 Connecting the Power Flue Cable 36
E5 Fixing the Appliance to the Base 36
E6 Network Cable 37
E7 Connecting the Gas Pipe to the Regulator 37

E8 Gas Isolating Valve 37
E9 Pressure Test Point 37
E10 Checking the Operating Pressure 38
E11 Converting the Appliance Gas Type 39
E12 Flame Picture 41
E13 Coal Fuelbed Installation 41
E14 Log Fuelbed Installation 41
E15 Installing the Glass 43
E16 Home Automation Setup 43
F Fitting the Fascia and Finishing Installation 44
F1 Fitting the Fascia 44
F2 Locating Wall Mount Cradle for Remote 44
F3 Operating the Appliance for the First Time 45
F4 Normal Operating Sounds and Smells 45
F5 Cleaning the Glass 46
G Freestanding Unit (DFS730) Installation 47
G1 Product Dimensions 47
G2 Hearth and Clearances 47
G3 Locating the DFS730 47
G4 Gas Pipe Routing Information 48
G5 Flue Installation 49
G6 Horizontal Flue Kit 50
G7 DF700 Fireplace Installation into DFS730 Freestanding Unit 50
H Installation Checklist 51
S Service Manual 52
S1 Error Codes 52
S2 Serial Number 54
S3 Checking Operating Pressure 54
S4 Cleaning the Fascia 54
S5 Removing or Cleaning Fan 55
S6 Removing Electronic Tray 55
S7 Replacing the Thermal Cut Out 56
S8 Removing the Pressure Switch 57
S9 Replacing a Remote 58
S10 Servicing the Horizontal/Universal Vertical Power Flue 59
S11 Annual Service Procedure 60
S12 Wiring Diagram 61

B
AC D E F G SERVICE
8
A Product Description and Installation Process
A1 Product Description
The Escea DF-Series gas fire is a room sealed gas appliance designed to be built into a masonry cavity
or a false chimney cavity. DF-series products are provided with stando rails to ensure adequate
clearances to combustible materials. DF990 is provided with an additional lintel spacer (see section;
creating the cavity). These appliances are flued using co-linear flexible aluminum flue (with PolyPro
flue extensions for some models) connected to a Power Flue. The user will control their fire with the
Radio Frequency (RF) remote that will normally be located in it’s wall mount cradle. In addition to the
RF remote the appliance has a single auxiliary On/O button on the unit. When not in operation it is
in a standby mode unless it is physically isolated from the mains supply.
A2 Recommended Install Process
The following diagram illustrates the steps required to install your gas fire. The sequence in which you
choose to do these tasks will vary depending on your individual scenario. Please read these instructions
fully before proceeding with the installation.
Masonry Installation
Modifying the
cavity to suit
Install electrical / gas
connections and ue
system
Install appliance and
nish cavity
Finish installation,
t fascia and test
appliance
Section B Section C, D Section E Section F
False Cavity Installation
Create The Framed-
Cavity
Install electrical / gas
connections and ue
system
Install appliance and
nish cavity
Finish installation,
t fascia, test appli-
ance and clad the
cavity
Section B Section C, D Section E Section F

BACDEFGSERVICE
9
Important: Installations that are not specifically outlined in this manual
should be referred to the Escea Architectural Advisory Team.
Please email [email protected]
i.e. Hutch, under bench, recessed, and joinery enclosed installations.
i.e. Use of heat sensitive materials such as resin stone or laminated timber.
i.e. DF flue installations over 4 metres.
To ensure that your installation is fully complete, please use the “Installation Checklist” on page 51.
A3 Product Dimensions
NOTE: All outside dimensions taken from the appliance are with the standos attached
*Slim Fascia Dimensions.
A
E*
D*
C
B
A B C D* E*
DF700 693mm 387mm 596mm 711mm 593mm
DF960 943mm 402mm 596mm 961mm 593mm
DF990 943mm 402mm 884mm 961mm 881mm
END OF SECTION A
By the end of this section, you should have:
□A framed false cavity
OR
□A masonry cavity sized to suit the appliance

B
AC D E F G SERVICE
10
B Creating the Cavity
B1 Cavity Shape
The stando rails installed on the outside must only be removed when being installed into a masonry
cavity.
Note: a top is not required when creating the cavity
Height Width Depth
DF700
False Cavity
installation (top standos
must be adjusted to the
upright position)
Framing 600mm
695mm
390mm +
minimum
65mm flue
clearances
Wall
Lining
560mm + allowance
for fascia clearance
*Masonry install with stando rails &
top standos removed. 560mm + allowance
for fascia clearance 685mm 385mm
DF960
False Cavity
installation (top standos
must be adjusted to the
upright position)
Framing 600mm
945mm
405mm +
minimum
65mm flue
clearances
Wall
Lining
560mm + allowance
for fascia clearance
*Masonry install with stando rails &
top standos removed. 560mm + allowance
for fascia clearance 935mm 400mm
DF990
False Cavity
installation (top standos
must be adjusted to the
upright position)
Framing 888mm
945mm
405mm +
minimum
65mm flue
clearances
Wall
Lining
848mm + allowance
for fascia clearance
*Masonry install with stando rails &
top standos removed. 848mm + allowance
for fascia clearance 935mm 400mm
WARNING: Wall lining MUST NOT be installed until after the fireplace is inserted into the cavity. Please
follow the steps in the figures shown.
WARNING: Ensure adequate allowances are made for fascias: see section B9 on page 15.
NOTE: Measure the indicated framing dimensions from the base of the appliance.
NOTE: If cavity dimensions significantly exceed those specified, a register plate is available for purchase
through your local Escea retailer (New Zealand Only).
D
H
W

BACDEFGSERVICE
11
False Cavity Installation Requirements
For floor-mounted installations, allow for fascia clearance, see B9 on page 15.
WARNING: DF700, DF960, and DF990: the top standos must be adjusted to the upright position
before the fireplace installation. All standos must remain in place for fireplace installation.
NOTE: Wall lining should hang below the lintel to meet the appliance edge.
Additional DF990 Specifications
B2 Floor Clearances
If the appliance is mounted above a “heat resistant floor” (including but not necessarily limited to:
ceramic tiles, concrete, and stone) then it may be positioned with the bottom of the fascia level with
the finished floor if desired.(30mm or 55mm spacer required under the fire in this case depending on
the fascia type.)
If the appliance is mounted above a “heat sensitive floor” (including but not necessarily limited to:
carpets, vinyl, carpet tiles, rugs and mats, timber, joinery, wooden flooring - see materials guide.) then
we recommend a distance of 100mm from the bottom of the fascia to the finished floor.
NOTE: “A gas appliance shall be installed such that the surface temperature of any nearby
combustible surface will not exceed 65C above ambient.” Excerpt from AS/NZS 5601.1-2013 Sec.
6.2.5.
Refer to section B4 on page 12 for hearths.
*Top
Standos
The fireplace is
inserted into the
cavity
Lintel:
Must sit above the
top standos
Wall lining thickness is
maximum 19mm
STEP 2
Lintel:
Must sit above the
top standos
Clearances; must cover
the full width of the appliance
=
STEP 1
1200mm
Cavity not to be
sealed within this
distance
20mm stando
to wall linings
Dwang/nogging/lintel MUST
be spaced 40mm away from
wall lining using provided
spacer bracket
40mm Spacer bracket
provided with DF990
Overlapping join to face
lintel/dwang/nogging
60mm Stando to
dwang/nogging/lintel

B
AC D E F G SERVICE
12
B3 Corner Installations
If a cavity is to be created in a corner, the following drawing gives the minimum sized interior wall
dimensions.
A B C
DF700 775mm 695mm 420mm
DF960 915mm 945mm 435mm
DF990 915mm 945mm 435mm
B4 Hearth
A finished floor level hearth is not required, however it may be used for decorative purposes or for
protection of soft/ heat sensitive flooring as stated in the section B2 on page 11 to allow a smaller floor
clearance. The hearth should not obscure the front face of the fire, must protrude at least 200mm
from the face of the fireplace and be at least the width of the appliance.
A raised hearth or joinery should conform to the above guideline.
B5 Cavity Base
This appliance MUST be fully supported on its base. The base must extend over the entire area of
the underside of the appliance. The base must also be levelled to prevent vibration from possible fan
imbalance. The base of the cavity must be strong enough to support 120kgs.
The fireplace must be seismically restrained in a manner appropriate to the installation location.
B6 Wall Linings
NOTE: For false cavity installations, DO NOT line the wall before the fireplace has been fitted into the
cavity; the top standos are required to be upright for this installation type.
The DF-Series fireplace has stando rails installed on the outside of the chassis. The stando rails may
only be removed when installing the fire into a masonry cavity. The side-front flanges of the appliance
must be on top of the finished wall surface in order for the fascia to mount properly. Take into account
any plaster board, tiles, or any other finishing surface that may be intended for the finished wall
surface.
The wall board that lines the outside of this opening can be normal dry wall (plaster board) and does
not need to be non-combustible.
If, for some reason, the cavity dimensions exceed those specified in section B1 on page 10, a
register plate is available (New Zealand only) for purchase through your local Escea distributor.
NOTE: The temperature of the wall lining directly above the heater does get warm and hence may discolour
paint finishes that are susceptible to temperature damage or distort vinyl wall coverings. For durability of
finishes and surfaces you should contact the relevant manufacturer for their specification.
45º
C
B
A

BACDEFGSERVICE
13
B7 Television & Mantel Clearances
Television
The diagram (shown below) shows the recommended minimum clearances for the location of any
electrical equipment (such as Plasma TV, LCD TV or home theatre) above a DF-Series gas fire.
For DF990 a mantel/recess is required to comply with our recommendation of TV installation.
Contact architectural advisory at [email protected] if you wish to install electrical equipment without a
mantel/with a recess.
NOTE: Dimensions from the top edge of the air opening.
NOTE: The television clearance recommendations are to be treated as a suggestion of a suitable installation
only. It is the responsibility of the end user to check the installation instructions of their electrical
appliances to ensure that the location in relation to the gas fire is suitable. Escea in no way guarantees or
takes responsibility that the recommended installation suggestion will be suitable for all electrical or home
entertainment appliances.
Mantel
Mantels or protruding ledges above the heater must not be installed lower than the dimension shown
to the right.
NOTE: Dimensions are from the top edge of the air opening.

B
AC D E F G SERVICE
14
B8 Fascia Dimensions
The dimensions of the fascias are shown below.
Edge Fascia
Slim Fascia & Stretch Fascia
A
T
C D
B
I
E
GH
F
Fascia
Type
E F G H I
DF700 Slim 711mm 620mm 592mm 529mm 2.5mm
Stretch 761mm 632mm
DF960 Slim 961mm 870mm 592mm 529mm 2.5mm
Stretch 1111mm 632mm
DF990 Slim 961mm 870mm 881mm 817mm 5.5mm
Stretch 1111mm 920mm
A B C D T
DF700 745mm 639mm 640mm 533mm 35mm
DF960 995mm 889mm 640mm 533mm 35mm
DF990 995mm 889mm 928mm 821mm 35mm

BACDEFGSERVICE
15
B8 Fascia Dimensions
The dimensions of the fascias are shown below.
Edge Fascia
Slim Fascia & Stretch Fascia
A
T
C D
B
I
E
GH
F
B9 Distance from Fireplace to Fascia Base
The installation requires a spacer below the appliance to allow room for the fascia to sit flush with the
non combustible floor or a hearth.
The following side-on view shows the measurement from the base of the fireplace to the base of the
fascia:
Spacer
55mm
Edge Fascia
Spacer
30mm
Slim Fascia &
Stretch Fascia
28
Slim Fascia &
Stretch Fascia
Fire
Base
52
Edge Fascia
Fire
Base
28
Slim Fascia &
Stretch Fascia
Fire
Base
52
Edge Fascia
Fire
Base

B
ACD E F G SERVICE
16
C Installing the Flue
C1 Flue Configuration (If less than 4m flue length is required)
If your flue system is less than 4m long (as shown in diagrams below), then a simple aluminium flexible
flue is required. If you wish to install a longer flue run, see either section C2 on page 18 or C3 on
page 19.
Horizontally Terminated: Utilizes the Escea Horizontal Power Flue enclosure kit.
The horizontal oset of the terminal can be any amount up to the total flue length listed below. Please
consult with Escea’s technical sta if your intended flue configuration steps outside of the bounds of
the flue configurations shown below.
X
Y
X+ YMaximum = 4m
YMaximum = 4m
YMinimum = 0m
XMaximum = 4m
XMinimum = 0m
X+ YMinimum = 0.4m
X
Y
X+ YMaximum = 4m
YMaximum = 1.5m
YMinimum = 0m
XMaximum = 4m
XMinimum = 0m
X+ YMinimum = 0.4m

BACDEFGSERVICE
17
Vertically Terminated: Utilizes the Escea Vertical Power Flue enclosure kit.
400mm Min.
4m Max.
Overall flue length:
X
Y
UVP Fan Unit
1.2m F-F Liner
UVP Cowl
X Max = 4m
Y Max = 4m
X + Y Max = 4m

B
ACD E F G SERVICE
18
C2 Flue Configuration (If more than 4m flue length is required)
If your flue system is greater than 4m long (as shown in diagrams below), then there are the following
options:
• DFS Only: Flexible flue with condensate trap and rigid PolyPro tube lengths (see diagrams
below).
• DF: For flue run installations beyond 4m and up to 12m, flexi flue must be used for the entire
flue run and must be fully insulated from appliance connection to fan unit. For information on the
insulation installation see section C10 on page 29. Beyond 12m (up to 40m) please contact
the Escea Advisory Team at [email protected].
Up to 12m MAX
Escea Wall
Terminal
Ø75mm / Ø100mm
Flexible flue
Insulation
Covering entire flue length
Fireplace
Up to 12m MAX
UVP Fan Unit
1.2m F-F Liner
UVP Cowl
Ø75mm / Ø100mm
Flexible flue
Insulation
Covering entire
flue length
Fireplace

BACDEFGSERVICE
19
C3 Masonry Vertical Power Flue Kit (up to 6m)
The following kit enables the installation of the aluminium flexi into vertical masonry chimneys for
extending the flue system from the appliance spigot to 6.0 meters while providing the masonry
flashing.
Including, but not limited to, installations into: a complete masonry chimney, a flue liner, or a combustible
sealed false chimney.
If your flue system is to be run vertically through a purpose-built sealed flue cavity (the cavity must
remain sealed up to the terminal); PolyPro and a condensate drain is not required. An extension kit
can be purchased to extend the maximum length to 12m, see section C4 on page 20. Only the
Universal Vertical Power Flue (UVP-External) kit can be used for this installation type.
NOTE: 225mm wide x 240mm long 906624-Masonry flue liner extension kit can be purchased to add extra
protection for the high snow and rainfall areas.
NOTE: If any gap occurs in between the 400mm x 400mm masonry flashing and the chimney due to the
chimney dimensions, the suitable chimney cap flashing can be built as keeping the spigot diameter 225mm.
6m Max
Ø75mm ID / Ø100mm ID
Flexible Flue
Purpose-built Sealed
Flue Cavity
Universal Vertical
Power Flue (External)
Masonry
Flashing
Chimney

B
ACD E F G SERVICE
20
C4 Masonry Vertical Power Flue Extension Kit (6 to 12m)
The following kit enables the installation of the aluminium flexi into vertical masonry chimneys for
extending the flue system to 12.0 meters from 906602-Masonry Vertical Power Flue kit that is
required and supplemented by the 12m Masonry Vertical Power Flue Extension Kit.
Including, but not limited to, installations into: a complete masonry chimney, a combustible sealed false
chimney.
NOTE: This installation type cannot be used on a DFS730. If required, please contact architectural advisory
[email protected] for more information.
If your flue system is to be run vertically through a purpose-built sealed flue cavity (the cavity must
remain sealed up to the terminal); PolyPro and a condensate drain is not required. Only the Universal
Vertical Power Flue (UVP-External) kit can be used for this installation type.
The exhaust/inlet flue MUST BE
NO longer than 12.0M.
The 100mm flue shroud must
cover the entire length of the
exhaust flue.
The intake and shrouded exhaust
flue must be entirely enclosed
within a fully vertical masonry
or purposely constructed, a
combustible sealed cavity/masonry
chimney.
Feed the power flue cable down
through the chimney cavity and
connect to the appliance and
Power Flue.
NOTE: This kit supplements and requires 906602-Masonry vertical Power Flue kit.
NOTE: If any gap occurs in between the 400mm x 400mm masonry flashing and the chimney due to the
chimney dimensions, the suitable masonry flashing can be built as keeping the spigot diameter 225mm.
6m to 12m
Ø75mm ID exhaust with
Ø100mm ID shield
Flexible Flue
Ø75mm ID Inlet unshielded
Flexible Flue
Transition Spigot
100mm ID Flexible Flue
75mm ID Flexible Flue
non-combustible
sealed flue cavity
Universal Vertical
Power Flue (External)
Masonry
Flashing
Chimney