Escea EF5000 User manual

EF5000
GAS FIRE USER GUIDE
New Zealand
630163_2
www.escea.net

NZ LTD
17 Carnforth st, Green Island
Dunedin, New Zealand
E-mail: [email protected]
Web: www.escea.net
Phone: [phone]
DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS
APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE
WHILST IT IS IN OPERATION.
IT IS NOT RECOMMENDED TO OPERATE THE FIRE WITH THE
FASCIA PANELS REMOVED.
THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG
CHILDREN OR INFIRM PERSONS UNLESS THEY HAVE BEEN
ADEQUATELY SUPERVISED BY A RESPONSIBLE PERSON TO
ENSURE THAT THEY CAN USE THE APPLIANCE SAFELY.
YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT
THEY DO NOT PLAY WITH THE APPLIANCE.
THE APPLIANCE MUST BE INSPECTED BEFORE USE AND AT LEAST
ANNUALLY BY AN AUTHORISED TECHNICIAN.
THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE
MANUFACTURERS WRITTEN INSTRUCTIONS.
Any service work carried out on this appliance must only be done by a
recognised escea technician or authorised personnel.
The data plate for this appliance, containing technical information and
specifications, can be found to the right of the control tray, near the
base of the fire. To access this, the fascia must be removed.

Contents
Basic Operation 1
Removing the Fascia 4
Replacing Batteries 5
Cleaning and Maintenance 6
The EF5000 electronic control system is designed to work within the
temperature range of 0°C to 70°C, with a humidity level that is non
condensing. This is to ensure safe operation of the electronic and
gas control system.
If the fireplace is subjected to an environment with temperatures
very close to or exceeding these temperature limits (irrespective of if
the fireplace is on or off at the time) the fireplace may not start up
until the temperature returns back to within the operating range.
To remedy this the environmental temperature should be addressed
and the fireplace control system given time to adjust accordingly.
The fireplace should then function correctly.

Basic Operation
On / Off
Flame Up
Flame Down
The EF5000 is operated by the touch control located on the right hand
side outer edge of the fascia. The basic operations possible from the
touch control are ON/OFF and manual adjustment of the flame height.
Before operating the fire, switch the Battery Isolating Switch on.
To turn on the fire push the ON/OFF button on the touch control.
The pilot will start sparking and gas will start flowing to the pilot
which should light and be visible in a few seconds.
The ignition process takes a duration of 12 seconds. No other button
should be pressed during those 12 seconds.
In the event of the pilot not igniting after 12 seconds press the
ON/OFF button. This will turn the valve off completely, then restart
the ignition process.
Ignition:

Basic Operation
Once the pilot flame has been running for 6 seconds press the
FLAME UP button to release gas to the two main burners
The EF5000 has 4 flame positions: PILOT flame only, LOW burner
flame, MEDIUM burner flame and HIGH burner flame.
Turning on the main burners:
While the fire is on, push the FLAME UP button or the FLAME
DOWN button to increase or decrease the flame height.
If the FLAME UP button is pushed while the fire is on HIGH burner
flame position, nothing will happen. Similarly if the FLAME DOWN
button is pushed while fire is in the PILOT flame position, nothing will
happen.
Adjusting the flame height:
To turn the fire off, you must push the ON/OFF button. This will shut
down the gas flow to the pilot flame and both burners.
Turning off the fire:
It is recommended that the fire be switched off by the isolating switch
when not in use

Basic Operation

Removing the Fascia
The EF5000 Stainless Steel fascia is attached to the fire by four
'hooks' on the corners of the fascia. If you need to remove the fascia,
first give the fascia a brief lift upwards as shown.
Now pull the fascia towards you, and rest the Fascia on the ground
. while you unplug the two cords connecting the fascia to the fire
Reverse these steps to re-fit the Fascia, ensuring the two connections
are correctly plugged in by testing the fire.

Replacing Batteries
The EF5000 uses 3x D sized batteries, To access the battery pack you
will need to remove the fascia (as described on previous page).
When the fascia has been removed, you will find the battery pack
located in the lower middle of the fire, situated inside the control box.
Remove the cap of the battery pack, turn it anti-clockwise until it stops,
then pull. The batteries inside should slide out.
Once the new batteries have been placed inside, (with the dimple
facing outwards) replace the cap and turn it clockwise until it stops, to
seal it.

Cleaning your EF5000
To clean the glass and stones in the front stone tray simply reverse the
steps in section 14.0 of the Installation Manual.
The glass can be cleaned using standard window cleaner. The quartz
stones can be washed using soapy water
If the stainless steel fascia requires cleaning the following products
are recommended; 3M Stainless steel cleaner or methylated spirits.
To clean the weather cover warm soapy water should be used.
Cleaning of the ceramic stones and burners can be carried out using a
brush and a dry cloth