ESI AC64v User manual

Page 1of 13 0455-0322 Rev A
eSIP and eCloud
AC64v Access Device Quick Install Guide
This guide instructs on installation and basic door unlocking settings of the ESI AC64v Access Device.

Page 2of 13 0455-0322 Rev A
Package Contents
Physical Specifications
Model
Device size
AC64v
7 x 3.47 x 1.43 inches (177.4 x 88 x 36.2 mm)
Front Panel

Page 3of 13 0455-0322 Rev A
Wiring Interface
Open the rear case of the device, there is a row of terminal blocks for connecting the power supply,
electric lock control, etc. The connections are as follows:
Reference
Number Description
1 Ethernet interface: standard RJ45 interface, 10/100M adaptive, Cat5e network cable or
better is recommended.
2 Two sets of short-circuit input detection interfaces: for connecting switches, infrared
probes, door magnets, vibration sensors and other input devices.
3 Wiegand interface.
4 RS485 interface.
5 Power interface: 12V/1A input up positive, down grounded.
6, 7 Two sets of short-circuit output control interface: used to control electric locks, alarms,
etc.
8 Line out interface.

Page 4of 13 0455-0322 Rev A
Wiring Instructions
NO: Normally Open Contact
COM: Common Contact
NC: Normally Close Contact.
Driving Mode Electric Lock Mode
Connections
Passive
No electrical
path when
open
Electrical
path when
open
√√
Electric lock (normally open type)
No electrical path to open door.
√√
Electric lock (normally closed type)
Electrical path to open door.
√√
Electric lock (normally open)
No power to open door.

Page 5of 13 0455-0322 Rev A
Installation Diagram
Panel Main Body Back Shell Wall Bracket
Wall mounting
Step 1: Installation preparation
• Check the following contents:
oKM3*6 screws x3
oTA4*30mm screws x5
o6*30mm screw anchors x5
oPM4*16mm screw x3
oTM6#*20/ screw x3
• Tools that may be required:
oPhillips screwdriver, hammer, RJ45 crimper
oElectric impact drill with an 8mm drill bit
Step 2: Drilling
1. Place the mounting template with dimensions on the surface of a wall in a desired flat position.
2. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill
about 50mm deep. Remove the template when finishing drilling.
3. Push or hammer screw anchors into the drilled holes

Page 6of 13 0455-0322 Rev A
Step 3: Removing hanging bracket and back shell.
Detach the wall bracket downward from the device and loosen the four screws on the rear cover using a
screwdriver, as shown below.
Step 4: Install the wall bracket, wiring and casing
1. Align the screw holes of the wall bracket with the holes in the wall and fix them to the wall with the
TA4*30mm screws, as shown below.

Page 7of 13 0455-0322 Rev A
2. Pass all the wires through the silicone plug in the middle of the bottom case. All lines should be
reserved for 15~20CM length, as shown below.
Note: The outlet hole of the bottom case faces down
3. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in
connectors description (refer to Section 2).
4. Connect the terminal of the wired cable to the motherboard socket. Refer to wiring interface.
5. Test whether there is electricity by doing the following: Press the # button for 3 seconds to get the IP
address of intercom by voice. Input access password or press the indoor switch to verify that electric
lock functions.
6 Attach the device to the wall bracket in a top-down manner, locking the screws at the bottom, as
shown below.

Page 8of 13 0455-0322 Rev A
Flush mounting
Step 1: Installation preparation
• Check the following contents:
oPM3*3mm screws x5
oPM3*4mm screws x5
o6*30mm screws anchors x5
oKB3*10mm screws x3
oTA4*30mm screws x5
• Tools that may be required:
oPhillips screwdriver, hammer, RJ45 crimper
oElectric impact drill with an 8mm drill bit
oDrywall saw
Flush mounting the device requires a box to be recessed into the wall as shown in the diagram below.
Finished Appearance
Exploded view
Decoration
panel
Small Stents
Access
Device
Wall box

Page 9of 13 0455-0322 Rev A
Accessing Web Interface
Getting IP Address
1. Power on device and wait for it to boot (about 30 seconds). Long press DSS key for 3 seconds.
2. When the speaker beeps rapidly, press the speed-dial button within 5 seconds.
The device will announce the IP address by voice.
In addition, the device can switch IP address acquisition mode (Static vs DHCP mode):
1. Press and hold the speed-dial button for 3 seconds.
2. Wait for the speaker to beep, and then press the speed-dial button three times within 5 seconds.
The device will announce the IP address by voice after successfully switching to the network mode.
Settings
Step 1: Log in the access device
Input IP address (e.g. http://192.168.1.128) into address bar of PC’s web browser. For eSIP, default user
and password are admin/admin. For eCloud, default user and password are admin/SIPstn@ESI.
Step 2: Add the SIP account.
Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.
Select “Activate”, and then click Apply to save this setting.

Page 10 of 13 0455-0322 Rev A
Step 3: Setting DSS key
Set the DSS key as shown below for a quick start. Click “Apply” to save this setting. Type: Memory Key.
Number 1: The DSS Key will dial to this Number 1.
Number 2: If Number 1 is unavailable, it will be forwarded to Number 2. Line: Working line.
Subtype: Speed dial
Step 4: Access Device Setting