Espressif PAN100 User manual

1Overview
The PAN100 is a WiFi and Bluetooth radio module from Espressif, part number ESP32-WROVER-IE that is
paired with a Taoglas antenna, part number FXP840.07.0055B. Refer to the manufacturer’s datasheets
for usage and specifications.
Device
Datasheet Name
ESP32-WROVER-IE
Esp32-wrover-e_esp32-wrover-ie_datasheet_en.pdf
FXP840.07.0055B
FXP840.07.0055B.pdf
2Radio Specifications
Parameter
Condition
Min
Typ
Max
Unit
Operating Frequency
2412
-
2484
MHz
Tx Power
11n, MCS7
12
13
14
dBm
Tx Power
11b mode
18.5
19.5
20.5
dBm
3Integration Instructions
This module has been granted modular approval for mobile applications. OEM integrators for host
products may use the module in their final products without additional FCC / IC (Industry Canada)
certification if they meet the following conditions. Otherwise, additional FCC / IC approvals must be
obtained.
The host product with the module installed must be evaluated for simultaneous transmission
requirements.
The user’s manual for the host product must clearly indicate the operating requirements and
conditions that must be observed to ensure compliance with current FCC / IC RF exposure
guidelines.
To comply with FCC / IC regulations limiting both maximum RF output power and human
exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only
exposure condition must not exceed 3.6 dBi.
A label must be affixed to the outside of the host product with the following statements:
oContains FCC ID: 2AVV3-PAN100
oContains IC: 11688B-PAN100
The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for
unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.
If the final host / module combination is intended for use as a portable device (see classifications below)
the host manufacturer is responsible for separate approvals for the SAR requirements from FCC Part
2.1093 and RSS-102.
4Operating Requirements
The following power levels for the 2.4 GHz WiFi modulations schemes listed below were needed to meet
FCC 15.247 conformity and will be needed in the final end-product, as set by the host software.

802.11g with 2.0 dB attenuation (8 X 0.25 dB).
802.11n 20 MHz channel bandwidth with 2.0 dB attenuation (8 X 0.25 dB).
802.11n 40 MHz channel bandwidth with 7.0 dB attenuation (28 X 0.25 dB).
5Compliance Notices
5.1 FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
5.2 FCC Part 15 Clause 15.21
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
5.3 FCC Interference Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
5.4 ISED Canada RSS-Gen Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes:

1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
5.5 ISED Canada Notice for Equipment with Detachable Antennas
This radio transmitter 11688B-PAN100 has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible
gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.
Antenna Type
Maximum Antenna Gain (dBi)
Antenna Impedance (Ohms)
Monopole
3.6
50