Eterna ELEDFLD10 User manual

Model:
ELEDFLD10 / 20 / 30 / 50
LED Economy Floodlights
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
Email: [email protected].uk / [email protected]o.uk
Visit our website: www.eterna-lighting.co.uk Made in ChinaIssue 1016
LAMP SPECIFICATIONS: 10W 20W 30W 50W
Luminaire lumens (with diuser) 1000 lm 1600 lm 2200 lm 3500 lm Lumens from chip (no diuser) 1100 lm 2000 lm 2600 lm 4100 lm Useful lumens 900 lm 1500 lm 2100 lm 3400 lm Rated Wattage 10W 20W 30W 50W
Rated luminous ux 900 lm 1500 lm 2100 lm 3400 lm Nominal life time of the lamp 30,000 hrs 30,000 hrs 30,000 hrs 30,000 hrs
Colour temperature 4000K 4000K 4000K 4000K
Number of switching cycles before premature lamp failure
15,000 15,000 15,000 15,000
Warm-up time up to 60 % of the full light output Instant full light Instant full light Instant full light Instant full light Dimmable No No No No LED dimensions (W/H) 17x12mm 25x18mm 43x33mm 43x33mm Nominal beam angle 100° 100° 100° 100° Rated power 10W 20W 30W 50W
Rated lamp lifetime 30,000 hrs 30,000 hrs 30,000 hrs 30,000 hrs
Lamp power factor 0.5 0.5 0.9 0.9 Lumen maintenance factor at end of nominal life 50% 50% 50% 50%
Starting time 0.5s 0.5s 0.5s 0.5s Colour rendering 65 65 65 65
Colour consistency Within a six step
Macadam ellipse
Within a six step
Macadam ellipse
Within a six step
Macadam ellipse
Within a six step
Macadam ellipse
Rated peak intensity 465cd 714cd 965cd 1508cd Rated beam angle 100° 100° 100° 100° Voltage / Frequency 240V~50Hz 240V~50Hz 240V~50Hz 240V~50Hz
Not suitable for accent lighting
1m
10W
50W
30W
20W
Pack Contents:
1 x LED oodlight
complete with 3
core x 80cm cable

READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product contains glass, care must be taken when
assembling, tting or handling to prevent personal
injury or damage to the product.
This product must be installed by a competent
person in accordance with the current building and
IEE wiring regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic service. Using
this tting in any other environments may result in a
shortened working life.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.
This unit is suitable for outdoor use.
This product is designed for permanent connection
to xed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
Make sure that the xings are strong enough to
support the considerable weight of the tting and
hold it rigidly and safely connected to the mains
supply (lighting circuit).
The lamp must be positioned so that there is at least
0.5m (500mm) between the bulb and any illuminated
surface.
When choosing the location for your new tting,
ensure that the xings will be anchored in a solid
surface e.g. concrete, brick or a joist—do not x
directly onto panelling, cladding, plasterboard etc.
When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product must be connected to earth
termination.
This product is not intended to be used by children
and persons with sensory, physical and/or mental
impairments that would prevent them from using it
safely.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.
INSTALLATION:
1. Choose the location for your new light tting
giving considerations to the points listed opposite.
2. Isolate mains.
3. Using the bracket, mark xing points and drill
xing holes, according to your chosen xing
method.
4. Terminate loose ends of wire to an appropriate IP
rated junction box or similar, ensuring the below
is observed.
Live - Brown / Red
Neutral - Blue / Black
Earth - Yellow / Green
5. Restore power and test the luminaire.
6. Adjust oodlight head towards the area to be
illuminated and lock o using two clamping bolts.
LAMP REPLACEMENT:
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Disconnect the power and clean the exterior only of
this tting with a moist (not wet) cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please
return it to the place where you bought it.
Our Technical Team will gladly advise on any
Eterna Lighting product, but may not be able to
give specic instructions regarding individual
installations.
874/2012
MODELNO.
ELEDFLD RANGE
The light source contained in this luminaire
shall only be replaced by the manufacturer,
service agent or a similar qualied person.
CAUTION, RISK OF ELECTRIC SHOCK.
The light source is designed to last the lifetime of the
luminaire.