ETI THERMAPEN ONE BLUE User manual

Operating Instructions
THERMAPEN®
ONE BLUE

CONNECTION - Use a Bluetooth Low Energy iOS or AndroidTM host device with
a compatible app installed to make connections to the instrument. When
connected, the Bluetooth symbol will show in the display.
Please note: No readings are stored in the instrument. When not connected, the
instrument can still be used. Readings are taken and displayed every 1 second.
TRANSFER BUTTON MEASURE/TRANSFER – When connected, press to measure
and transfer result via Bluetooth.
INSTRUMENT OPERATION – The instrument
is switched on by unfolding the probe and
turned off by folding the probe until fully
located into the rubber probe retainer.
The probe should not be rotated more
than 180 degrees as damage will occur.
It is recommended to store the probe
in the closed position, when not in use.
Apply the tip of the probe to the substance, medium or surface to be measured.
The sensor is located at the tip of the probe, therefore the minimum depth
insertion should be 3 mm.
The probe tip is very sharp and therefore caution should be taken when
using. Care should also be taken when closing the probe after taking hot
temperatures as the probe may remain hot.
SETTINGS - Adjustable via the app and include: °C or °F, Measurement Interval,
Display Sleep Interval, Connection Status Display, Display mode, Auto-off Interval,
Sensor Name and High/ Low Alarm levels. All settings are stored in the instrument
and are downloaded to the app on connection.
DISPLAY – The display has two modes,
basic mode and enhanced mode. Basic
mode will be shown when not connected
to Bluetooth. Enhanced mode will be shown
when connected and enabled via settings.
Please note: Enhanced display mode, Sleep Interval, and Connection Status
Display Settings, are only available when using software compatible with the latest
SDK/Protocol. When using the unit with older software, the display will remain in
Basic mode at all times.
!
Basic Advanced

ROTATIONAL DISPLAY - The display will rotate 180° depending on the direction
the instrument is pointing so that it can be used in either hand.
DISPLAY SLEEP INTERVAL – the display will ‘SLEEP’ after a settable time (default
30 seconds), when no movement has been detected. The instrument will remain
connected whilst in display sleep and will wake up when movement is detected.
INTELLIGENT BACKLIGHT - features a light sensor
which will automatically turn the backlight on in
low light conditions. The backlight will remain on
for 10 seconds and automatically turn off if no
movement is detected.
AUTO-OFF - If the instrument is not connected to
Bluetooth within the set auto-off interval, it will shut down.
The timer is reset with any movement or button press.
STORAGE & CLEANING – Clean the instrument regularly
with an anti-bacterial probe wipe to avoid potential
food-borne bacteria growth. The thermometer should
be stored between -20 to 60 °C. WARNING: IPA and
other solvents may cause damage to the case and
screen of this instrument.
BATTERY REPLACEMENT - A battery symbol
‘ ’ indicates that the batteries will need replacing.
The instrument continues to measure accurately
but we recommend that the batteries be changed
as soon as possible.
To replace the battery, loosen the battery cover
screw using a Pozi (PZ1) screwdriver to remove
the battery cover. Replace with a single AAA battery
noting the polarity. Tighten the battery cover screw
until the battery cover is snug onto the seal.
Do not over-tighten.
AMBIENT- The ambient operating range is -20 to 50 °C.
LCD ERROR MESSAGES - If the ambient temperature falls outside the operational
range, then either ‘Amb-Lo’ or ‘Amb-Hi’ will be displayed. This will continue until
the ambient temperature has returned within the limits. The thermometer should
be allowed plenty of time (minimum 30 minutes) to stabilise to the working/
room temperature. ‘Hi-Err’ or ‘Lo-Err’ will be displayed when the temperature
being measured is outside of the instrument’s measurement range. ‘Error’ will be
displayed if the instrument has developed a fault.
.

545-607 WEB/15.09.23
Manufactured by
Electronic Temperature Instruments Ltd
Worthing · West Sussex · BN14 8HQ
01903 202151 · [e-mail] · etiltd.com
GUARANTEE - This instrument carries a two-year guarantee against defects in either
components or workmanship. During this period, products that prove to be defective
will, at the discretion of ETI, be either repaired or replaced without charge. This
guarantee does not apply to sensors/probes, where a six-month period is offered. The
product guarantee does not cover damage caused by fair wear and tear, abnormal
storage conditions, incorrect use, accidental misuse, abuse, neglect, misapplication,
or modification. Full details of liability are available within ETI’s Terms & Conditions
of Sale at etiltd.com/terms. In line with our policy of continuous development, we
reserve the right to amend our product specification without prior notice.
The Bluetooth®word mark and logos are registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such marks by ETI is under license.
Google Play and the Google Play logo are trademarks of Google Inc.
Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries. App Store is a service mark of Apple
Inc., registered in the U.S. and other countries.
iOS is a trademark or registered trademark of Cisco in the U.S. and other
countries and is used under license. Android is a trademark of Google Inc