Euchips Eup150d-1w24v-0 User manual

100VAC-240VAC

47/63Hz

91%@230VAC,Full load

≥0.95@115VAC,Full load

Cold start,40A@230VAC

0.5Amax@230VAC

206*75*41mm（L*W*H）

IP20

-30℃~40℃

-40℃~85℃, 20-90%RH

90℃

EN50515, EN61000-3-2

EN61000-4-2, 3, 4, 5, 6, 8, 11; EN61547

EN61347, GB19510

L-N:1KV

I/P-O/P: 3000VAC/1min/5mA

Metal

30,000h@tc:80℃

1%-100% Dimming to off

±3%

70mVp-p

DALI Dimming / Touch-dim

>15,000 times

6.25A/24VDC/150W

<10%@230VAC, Full load

EUP150D-1W24V-0

Surge

Withstand Voltage

Safety Standards

IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI Standard

EMC Emission

EMC Immunity

Lifetime

Material

Dimming Range

Dimension

Net weight: 668g±5%/PCS; 18PCS/Carton;13kg±5%/Carton; Carton Size: 303*221*265mm(L*W*H)

Packing(weight)

IP Rating

Working Temp.

Storage Temp., Humidity

Dimming Type

Switch Cycle

3 yearsWarranty Condition

Turn on delay Time <1.5s, at230Vac (When the light begins to shine)

Efficiency

AC Current(max)

Inrush Current(max)

THD(full load)

Current(mA)/Voltage (VDC) Power(W)

R & N (Max)

Channel

Current Tolerance

Voltage

Frequency Range(Hz)

Power Factor

Short Circuit

Over current

Hiccup, recovers after fault condition is removed

Constant current limiting, recovers automatically after removed

Safety&

EMC

Others

Function

Model

Output

Input

Protection

DALI Constant Voltage Dimming Driver

Product Features

EUP150D-1W24V-0 (Product No.:102200041101)

1/2

User’s manual: 2019-9 www.euchips.com

Dimension(mm)

Technical Paramaters

Application

Wall Washer LED Strip Light LED Tube Underground Light AR111 Venture Light

· Single channel constant voltage, 24VDC output.

· Meet DALI Protocol IEC62386

· Wide range of input voltage 100VAC ~ 240VAC

· Support Touch-DIM function

· High efficiency up to 91%

· Built-in active PFC function

· Protections: Short circuit, Over current.

· IP 20 design

· Suitable for indoor LED lighting application

206

186

40.5

DALI Constant Voltage Dimming Driver

2/2

User’s manual: 2019-9 www.euchips.com

DALI Wiring

※The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions,

the function of the product shall prevail.Please contact us if you have any questions .

Cautions

1.This product should be installed by qualified personnel.

2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.

3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.

4.Please make sure LED power supply output voltage, current is used to meet the product requirements.

5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.

6.Due to safety concerns, PVC or rubber cord of 0.75- 2.5mm²is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire

connections and polarities are correct before applying power to avoid any damages to the LED lights.

7.In case of malfunction, do not repair it yourself.

0120 40 60 80 100 120 140 160 180 200 220 240 254

100

120

110 20 30 40 50

0.1

0.2

0.3

0.4

DALI Dimming Level

Output Current(%)

Push DIM(Touch DIM) DiagramDALI Diagram

Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.

Push DIM Function

1. Press the Push DIM (Touch DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.

2. Short press the Push DIM (Touch DIM) switch (<0.5s) to control the lamp on or off.

3. Long press the Push DIM (Touch DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.