EUFY Clean G40 Hybrid+ User manual

eufy Clean G40 Hybrid+
Owner’s Manual
T2273 51005003474 V01

EN 01
Thank you for purchasing RoboVac. Carefully read all the instructions below
before using this device, and keep this manual for future reference.
Table of Contents
02 Important Safety Instructions
09 About Your RoboVac
What's in the Box
RoboVac Anatomy
LED Indication
13 Using Your RoboVac
Important Tips Before Use
Preparation
Use the Auto-Empty Station
Use Your RoboVac with the eufy Clean App
Start / Pause Cleaning
Select a Cleaning Mode
Select a Suction Power Level
Use Mopping System
Use RoboVac with Amazon Alexa / The Google
Assistant
27 Cleaning and Maintenance
Clean the Dust Box, Water Tank, and Filter
Clean the Rolling Brush
Clean the Side Brush
Replace the Side Brush
Clean the Sensors and Charging Pins
Clean the Swivel Wheel
Clean the Mopping Cloth
Replace the Dust Bag
Clean the Auto-Empty Station
39 Troubleshooting
Voice Alert
43 Specifications
44 Customer Service

02 EN EN 03
Important Safety Instructions
To reduce the risk of injury or damage, keep these instructions
at hand when setting up, using, and maintaining this device.
WARNING SYMBOLS USED
This is the safety alert symbol. This symbol alerts you to
potential hazards that could result in property damage
and/or serious bodily harm or death.
• This device can be used by individuals aged 8 years
and above and individuals with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of this device in a safe way
and understand the hazards involved.
• Children should be supervised to ensure they do not play
with this device.
• Cleaning and maintenance shall not be performed by
children without adult supervision.
• This device is only to be used with the auto-empty
station provided.
• Before cleaning or maintaining this device, the plug must
be removed from the outlet.
• The battery in this device should only be replaced by a
skilled professional.
• Before removing the battery, disconnect the device from
its power supply.
• The battery must be removed before this device is
disposed of. To remove the battery, first unscrew
the screws on the bottom, then remove the back
cover. Remove the battery by disconnecting the quick
connector.
• The used battery should be placed in a sealed plastic bag
and disposed of safely according to local environmental
regulations.
• This device is for indoor use only.
• This device is not a toy. Do not sit or stand on this device.
Small children and pets should be supervised when this
device is operating.
• Store and operate this device in room temperature
environments only.
• Do not use to pick up flammable or combustible liquids,
such as gasoline, or use in areas where they may be
present.
• Before using this device, pick up objects like clothing and
loose paper. Lift up cords for blinds or curtains. Move
power cords and sharp, pointed, or fragile objects out of
the way. Be aware that if this device passes over a power
cord and drags it, an object could be pulled off a table or
shelf.
• If the room to be cleaned has a balcony, a physical barrier
should be used to prevent access to it to ensure safe
operation.
• Do not place anything on top of this device.
• Be aware that this device moves around on its own.
Take care when walking in the area where this device is
operating to avoid stepping on it.
• Do not operate this device in areas with exposed
electrical outlets on the floor.
• Do not expose the electronic components of this device,
its battery, or the auto-empty station. There are no user-
serviceable parts inside.
• Do not use this device on carpets with tasseled edges or
loose threads or on an unfinished, unsealed, waxed, or
rough floor, as it may result in damage to the floor and
this device. Use only on hard floor surfaces or low-pile
carpets.
• This device has been designed to be used on floors without
scratching them. We recommend that you test this device
on a small area of the room to be cleaned to ensure no
scratches are made before cleaning the whole room.

04 EN EN 05
• Only use attachments recommended or described in this
manual.
• Do not handle the device or plug with wet hands.
• Ensure that the dust bag and/or filters are correctly in
place before use.
• Do not use a battery pack or device that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion, or risk
of injury.
• Do not expose the battery pack or device to fire or
excessive heat. Exposure to fire or temperatures above
130°C / 266℉may cause an explosion.
• Do not modify or attempt to repair the device or the
battery pack, except as indicated in the instructions for
use and care.
• Follow all charging instructions and do not charge the
battery pack or device outside of the temperature range
specified in the instructions. Charging improperly or at
temperatures outside of the specified range may damage
the battery and increase the risk of fire.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord. Keep cord away from heated surfaces
• Turn off all controls before unplugging.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair, and anything
that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts.
• Use extra care when cleaning on stairs.
Notice
This symbol on the device or its packaging
indicates:
Do not dispose of electrical appliances as unsorted
municipal waste; use separate collection facilities.
Contact your local authority for information
regarding the collection systems available. If
electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging
your health and well-being. When replacing old
appliances with new ones, the retailer is legally
obliged to take back your old appliance for disposal
free of charge.
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and radiates radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a

06 EN EN 07
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment on and off,
the user is encouraged to try to correct the interference
by one or more of the following measures: (1) reorient or
relocate the receiving antenna. (2) Increase the separation
between the equipment and receiver. (3) Connect the
equipment into an outlet on a circuit different from that to
which the receiver is connected. (4) Consult the dealer or
an experienced radio / TV technician for help.
The following importer is the responsible party (for FCC
matters only).
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA
98004-5541
Telephone: [phone]
RF Exposure Compliance Statement
This equipment complies with the FCC/IC radiation
exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a
minimum distance of 20 cm between the radiator and
your body.
ISED Compliance Statement
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
Declaration of Conformity
This product complies with the radio interference
requirements of the European Community. Hereby, Anker
Innovations Limited declares that the radio equipment type
T2273 is in compliance with Directive 2014/53/EU. The
full text of the EU Declaration of Conformity is available
at the following website: https://support.eufylife.com/s/
articleRecommend?type=DownLoad.
Maximum output power: 18 dBm (For EU)
Frequency band: 2.4G band (2.4000GHz - 2.4835GHz)
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that
the product type T2273 is in compliance with Radio
Equipment Regulations 2017 and The Restriction of
the Use of Certain Hazardous Substances in Electrical
and Electronic Equipment Regulations 2012. The full
text of the GB Declaration of Conformity is available at
the following website: https://support.eufylife.com/s/
articleRecommend?type=DownLoad.
The following importer is the responsible party for EU and
UK matters.
Anker Technology (UK) Ltd
GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17
1HP, United Kingdom
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
Manufacturer :
Anker Innovations Limited

08 EN EN 09
Room 1318-19, Hollywood Plaza, 610 Nathan Road,
Mongkok, Kowloon, Hong Kong
Trademark Notice
• Amazon, Echo, Alexa and all related logos are trademarks
of Amazon.com, Inc. or its affiliates.
• Apple and the Apple logo are trademarks of Apple Inc.,
registered in the U.S. and other countries. App Store is
a service mark of Apple Inc., registered in the U.S. and
other countries.
• Google Play and the Google Play logo are trademarks of
Google Inc.
• Google Home is a trademark of Google Inc.
About Your RoboVac
What's in the Box
RoboVac
Additional Dust Bag
Protective Pad
Disposable mopping cloths
(x5)
Washable Mopping Cloth
Auto-Empty Station
Additional Side Brush
Cleaning Tool
Mopping module
Power Cord
Additional Filter
Cable Ties (x5)
Owner’s Manual &
Other Documents

10 EN EN 11
RoboVac Anatomy
A. Top & Side
Charging Contact Pins (x2)
Dust box and water tank release button
Dust box and water tank (2-in-1)
Mopping module
Recharge Button
Auto-Cleaning Start/Pause Button
Wi-Fi Status Light
Bumper
Infrared Sensor
Main Power Switch (On/O)
Spot Cleaning Button
B. Bottom
Brush Guard
Swivel Wheel
Path Tracking Sensor
Battery Compartment
Rolling Brush
Hall Sensors (x2)
Charging Contact Pins (x2)
Side Brush
Drop Sensors (x4)
Wheels (x2)
C. Dust Box and Water Tank (2-in-1)
Release button
Water inlet cover
Water inlet
Filter
Dust box
Water tank
D. Mopping Module
Cloth attachment area
Washable mopping cloth
E. Suction Inlet
Dust Box and Water Tank (2-in-1)
Suction Inlet Suction Inlet
F. Auto-Empty Station
Storage Compartment
Dust Bag
Top Cover
Dust Bag Handle
Power Indicator
Debris Evacuation Port
Charging Contact Pins (x2)
High-Performance Filter
Filter Assembly
Charging Socket

12 EN EN 13
LED Indication
You can see the status of RoboVac from the LED indicators.
Start / Pause Cleaning
• Steady blue: standby, cleaning, cleaning paused,
returning to auto-empty station, or fully charged
• Steady orange: standby or working in low
battery
• Pulsing orange (when docked to auto-empty
station): charging
• Flashing red: error (Refer to the
"Troubleshooting>Voice Alert" section in this
manual for solutions)
Reset the Wi-Fi Connection (Press and hold for 10
seconds)
Return to Auto-Empty Station
• Flashing blue slowly: returning to auto-empty
station
• Steady blue: standby or paused
Spot Cleaning
• Flashing blue slowly: Spot mode
• Steady blue: standby or paused
• When you use the Find My Robot function via the eufy Clean app, all three
LED indicators are steady blue and a voice prompt is heard.
• To conserve power, the blue light on the button becomes dim when:
• RoboVac is not docked to the auto-empty station and has been
inactive for 10 minutes;
• RoboVac has been fully charged for 1 minute.
Using Your RoboVac
Important Tips Before Use
A
D
B
E
C
F
Remove power cords and small objects from the floor that may entangle RoboVac.
Fold tasseled edges of rugs underneath to prevent tangling RoboVac. Avoid
cleaning dark-colored high-pile rugs or rugs thicker than 1.02 in / 26 mm as they
may cause RoboVac to malfunction.
It is strongly recommended to place physical barriers in front of fireplaces and
certain areas (i.e. air vents) that may cause damage to RoboVac if entered.
Keep RoboVac away from wet areas during cleaning.
RoboVac may climb on top of objects less than 0.63 in / 16 mm in height. Remove
these objects if possible.
Anti-drop sensors will prevent RoboVac from tumbling down stairs and steep
drops in most cases. Sensors are less effective if dirty or used on carpeted,
reflective, or dark-colored floors. Place physical barriers to block off areas where
RoboVac may fall.

14 EN EN 15
Preparation
1
Remove the foam blocks beside the bumper before use.
2
Install the side brush before use.
3
Turn on the main power switch on the right side of RoboVac.
4
Place the auto-empty station on a level surface and against a wall.
5
Install the supplied protective pad under the auto-empty station before using it
on a carpet.

16 EN EN 17
6
Remove objects within 3.3 ft/1 m to the left and right sides and within 6.6 ft / 2
m of the front of the auto-empty station. If you cannot remove the objects, check
whether RoboVac can return to the auto-empty station normally. If not, contact
eufy Customer Service for help.
7
Connect the power cord to the auto-empty station and a wall outlet.
When the auto-empty station connects to AC power, the LED indicator on
the auto-empty station is steady white.
• The auto-empty station has two versions: high-voltage and low-voltage.
The voltage information can be found on the bottom of the device. Make
sure you have purchased the device with the correct voltage, otherwise it
may not work normally.
• Install the auto-empty station in a location that RoboVac can easily access.
It is recommended to place the auto-empty station against a wall, and on a
hard, level surface rather than on rugs or carpets.
• Always keep the auto-empty station plugged in, otherwise RoboVac will
not automatically return to it.
Use the Auto-Empty Station
• RoboVac will return to the auto-empty station at the end of a cleaning
cycle or when its battery is running low.
• Make sure the power cord is connected to a power outlet and the dust bag
is properly installed.
• Based on eufy's internal laboratory tests, the dust bag can lock 99.7% of
allergens (such as dust, garbage, dust mites, pet dander, etc.) to prevent
them from emitting into the air.
• If the cleaning time or the time period between two cleaning sessions is too
short, the auto-empty station may not empty the dust box automatically.
• The emptying function will not be activated if you have selected the Do-
Not-Disturb mode in the eufy Clean app.
• Certain noise may exist when the auto-empty station is working. You are
recommended to place the device in a proper location or select the Do-
Not-Disturb mode in the eufy Clean app to prevent noise interference.
Attach RoboVac to the auto-empty station by aligning its charging pins.
RoboVac starts charging automatically.
If RoboVac has finished a round of cleaning (more than 15 minutes), it will empty
the dust box automatically by default when it returns to the auto-empty station.

18 EN EN 19
LED Indicator
Status of Auto-Empty Station
Steady white, with 50%
brightness Standby
Flashing white slowly Working normally
Flashing white quickly
Working abnormally
(Refer to the "Troubleshooting" section in this manual
for solutions)
• Turn off the main power switch if RoboVac will not be used for a long
period of time. To preserve the battery's lifespan, recharge at least once
every 6 months.
Store Accessories
Store your frequently-used accessories in the storage compartment of the auto-empty
station, such as the filter, side brush, dust bag, and cleaning tools. To prevent any damage
or unpleasant smells, things that are damp should not be stored inside the auto-empty
station.
Use Your RoboVac with the eufy Clean App
To enjoy all the available features, it is recommended to control your RoboVac via the eufy
Clean app.
Before you start, make sure that:
• Your smartphone or tablet is running iOS 10.0 (or above) or Android 5.0 (or above).
• The 2.4GHz band wireless signal is enabled on your wireless router.
• RoboVac is attached to the auto-empty station to ensure it has enough power during
setup.
eufy Clean
eufy Clean
1
Download the eufy Clean app from the App Store (iOS devices) or Google Play
(Android devices).
2
Open the app and create a user account.
3
Tap the “+” icon to add RoboVac to your eufy Clean account.
4
Follow the instructions in the app to set up the Wi-Fi connection.
After connecting successfully, you can control RoboVac via the app.
With the app, you can select a cleaning mode, set the time, schedule a cleaning,
adjust suction power, view system status, receive notifications, and access
additional features.
Slowly flashing blue Waiting for connection
Rapidly flashing blue Connecting with your wireless router
Steady blue Connected with your wireless router
• If RoboVac gets stuck in any space, tap Find My Robot in the app to find
the device.

20 EN EN 21
Restore Factory Settings
Press and hold on RoboVac for 10 seconds to restore factory settings if necessary.
You will hear a voice prompt when the settings have been reset and the Wi-Fi
status light will slowly flash blue. Now you can follow the Wi-Fi instructions in the
eufy Clean app to set up the Wi-Fi connection.
Schedule Cleaning
With the eufy Clean app, you can schedule RoboVac to start cleaning at a particular time.
• You can set the time and customize the cleaning schedules from Sunday to
Saturday on the eufy Clean app. This function is only available on the app.
Start / Pause Cleaning
• Make sure the main power switch at the side of RoboVac is turned on
before use.
• You can also start or pause cleaning via the eufy Clean app.
1
Press on RoboVac to start cleaning in Auto-Cleaning mode.
2
Press again to pause cleaning.
Select a Cleaning Mode
• You can also select the cleaning mode via the eufy Clean app.
Auto-Cleaning Mode
After startup, RoboVac moves from the auto-empty station and automatically determines
its cleaning route, following a Z-shaped cleaning path. When the cleaning is finished,
RoboVac automatically returns to the auto-empty station.
Press to start cleaning in Auto-Cleaning mode.
• In the eufy Clean app, RoboVac can be set to return to the auto-empty
station automatically if the battery level becomes low. Once recharged,
RoboVac will resume cleaning.
• By default, RoboVac starts in Auto-Cleaning mode when it is turned on.

22 EN EN 23
Spot Cleaning Mode
RoboVac intensively cleans a specific area in a spiral pattern, which is useful if there is a
concentrated area of dust or debris. In Spot Cleaning mode, RoboVac will stop cleaning
after 2 minutes.
•Press on RoboVac to start cleaning in Spot Cleaning mode.
Select a Suction Power Level
In the eufy Clean app, select a suction power level according to your needs:
•Quiet
•Standard (Default)
•Turbo
•Max
• When RoboVac starts cleaning next time, it will clean according to the
suction power level you previously selected.
Select BoostIQ™ feature
In the eufy Clean app, select the BoostIQ™ feature according to your needs. RoboVac will
automatically increase suction power if it detects that stronger power is needed to ensure
the best clean. BoostIQ™ is ideal for cleaning thicker carpets and hard-to-sweep messes,
which will reduce the total cleaning time but increase the noise level. If the vacuuming
noise caused by BoostIQ™ disturbs you, you can disable this feature.
Use Mopping System
• The mopping mode is only intended for a clean floor without stubborn stains
or liquids. To avoid staining floors, do not use the mopping function when
dust is mixed with liquids such as coffee or ink.
• Mopping system cleans best on smooth hard surfaces and may not perform
so well on uneven tiles, heavily waxed floors or rough surfaces like slate or
brick, which may snag the mopping module.
• The mopping mode is not recommended for use when no one is at home.
• Do not use the mopping mode on a carpeted floor. It is recommended to set
a physical barrier to avoid cleaning the carpeted area.
1
Before mopping, install the protective pad under the auto-empty station to protect
the floor.
2
Remove the mopping module.

24 EN EN 25
3
Wet the mopping cloth and wring it until it does not drip, then attach the cloth to
the mopping module.
Use either washable or disposable cloth for mopping. The disposable mopping cloth
is for single use only.
4
Remove the water tank.
5
Open the water inlet cover to fill with water, then close the cover.
• Do not use any cleaning solution, as your floor may become slippery and
therefore affect the cleaning effect.
6
Install the water tank and the mopping module under RoboVac with a click.
• The mopping mode is only intended for a clean floor without stubborn stains.
To achieve a better mopping effect, it is recommended to clean the floor with
RoboVac three times before mopping.
7
Start cleaning. RoboVac will automatically vacuum and mop. During mopping, you
can choose among three water levels via the eufy Clean app.
8
When RoboVac finishes cleaning, remove the mopping module.

26 EN EN 27
9
Remove the dust box and the water tank.
10
Clean the dust box and water tank, empty any remaining water, and clean the
mopping cloth to prevent mildew or unpleasant smells. For how to clean and
maintain the components, refer to the “Cleaning and Maintenance” section in this
manual.
Use RoboVac with Amazon Alexa / The Google Assistant
Amazon Alexa or the Google Assistant is a smart voice control device that enables you to
control RoboVac with your voice.
Before you start, make sure that:
• RoboVac is attached to the auto-empty station to ensure there is enough power.
• RoboVac is connected with the eufy Clean app.
• You have an Amazon Alexa-enabled device (i.e. Amazon Echo, Echo Dot, Amazon Tap,
Echo Show, or Echo Spot) or a device enabled with the Google Assistant (i.e. Google
Home, Google Home Mini). These devices are sold separately.
• The Amazon Alexa app or Google Home app is already installed on your smart device,
and you have created an account.
To control RoboVac with Amazon Alexa or the Google Assistant:
1. Open the eufy Clean app and find “Smart Integrations” in the top left.
2. Follow the on-screen instructions to complete the setup.
• Currently, this feature only supports a few languages including English,
German, French, Portuguese, and Spanish. For more supported languages,
check https://www.eufylife.com/support/.
Cleaning and Maintenance
Prior to cleaning and maintaining, turn o the device and unplug the power cord.
For optimal performance, follow the instructions below to clean and maintain RoboVac
regularly. The cleaning and replacement frequency will depend on your RoboVac
usage habits.
Recommended Cleaning and Replacement Frequency
RoboVac Part Cleaning Frequency Replacement Frequency
Dust Box and
Water Tank
(2-in-1)
Dust Box: Once a week
Water Tank: After each use -
Washable
Mopping Cloth After each use -
Dust Collector Once a week -
Filter Once a week
(Twice a week if you have a pet)
Every 6 months or after every
50 rounds of cleaning
Side Brush Once a month Every 3-6 months (or when
visibly worn)
Brush Guard Once a month Every 3-6 months (or when
visibly worn)
Rolling Brush Once a month Every 6-8 months
Sensors Once a month -
Charging Pins Once a month -
Swivel Wheel Once a month -
Dust Bag - Every 60 days
Clean the Dust Box, Water Tank, and Filter
1
Press the release button to remove the dust box and water tank.

28 EN EN 29
2
Open and empty the dust box.
3
Remove the filters.
4
Tap the filters to remove dust.
5
Rinse the dust box, water tank, and filters thoroughly with water.
1 min
• Do not use a brush, hot water, or any detergent to clean the filter.
6
Air-dry the dust box, water tank, and filters completely before next use. You may
use another filter if the original one is not dry.
24h
• Do not use the filters if they are not completely dry, otherwise it may affect
the cleaning performance.

30 EN EN 31
7
Place the filters back into the dust box and the auto-empty station.
8
Push the dust box and water tank back into the main unit.
Clean the Rolling Brush
1
Pull on the release tabs to unlock the brush guard, as shown.
2
Lift the rolling brush to remove.
3
Clean the rolling brush with the cleaning tool.
4
Reinstall the rolling brush by inserting the fixed protruding end first.
5
Press down to snap the brush guard into place.
1 2
3
54

32 EN EN 33
Clean the Side Brush
Foreign substances, such as hair, can easily get tangled in the side brush, so it is best to
clean it regularly.
1
Remove the side brush.
2
Carefully unwind and pull off any hair or substances that are wrapped between the
main unit and the side brush.
3
Use a cloth dampened with warm water to remove dust from the brush or to
gently reshape it.
• Only use the side brush when it is completely dry.
Replace the Side Brush
The side brush may become bent or damaged after being used for a period of time.
Follow the instructions below to replace it.
• Pull off the old side brush and snap the new one into place until you hear a click.
Clean the Sensors and Charging Pins
To maintain the best performance, clean the sensors and charging contact pins
regularly.
• Dust off the sensors and charging contact pins using a cloth or cleaning brush.

34 EN EN 35
• Clean the path tracking sensor with a soft, dry cloth.
• Be careful not to touch the path tracking sensor with your hands.
• Do not clean the path tracking sensor with sharp-pointed objects, as it may
damage the sensor.
Clean the Swivel Wheel
Hair or dust particles can easily get entangled in the swivel wheel. Be sure to clean the
swivel wheel periodically and as needed.
Wheel
Axle
1
Pull out the swivel wheel with a tool (such as a screwdriver).
2
Clean any hair or debris wrapped around the wheel or entangled inside the wheel
cavity.
3
Reinstall the wheel and push it in until it clicks into place.
• Do not clean the swivel wheel with water.
Clean the Mopping Cloth
It is recommended to clean the washable mopping cloth after each use.
24h
1
Remove the mopping cloth from the mopping module.
2
Rinse the mopping cloth thoroughly with water.
3
Air-dry the mopping cloth completely to prevent mildew or unpleasant smells.

36 EN EN 37
Replace the Dust Bag
1
Lift open the top cover.
2
Remove the dust bag.
1
2
3
Discard the used dust bag.
4
Install a new dust bag.
1
2
5
Press down to close the top cover.