Euro chef Mg900 User manual

Meat Grinder

MG900

User Manual

[Revision 2.0 July 2020]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE

AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may

vary in appearance, assembly, inclusions, specifications, description and packaging.

Meat Grinder – MG900

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

•Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

•Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

•Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

•Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

•Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

•This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

•Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

•Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

•The equipment is designed for domestic

use only.

•Handle the equipment safely and carefully.

•Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

•Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

•Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

•Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

•The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and care,

see Equipment Safety.

Meat Grinder – MG900

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

•Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and safety

codes.

•Wherever possible, use a residual current

device (RCD).

•High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

•Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

•Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift, move or

carry equipment.

•Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

•Do NOT attempt any maintenance or repair

work not described in this manual.

•After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories or performing repair or

maintenance.

•Do NOT adjust while the equipment is

running.

•Perform service related activities in suitable

conditions, such as a workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Meat Grinder Safety

When using electrical appliances, basic safety precautions should always be followed including the following:

•Read all instructions.

•To protect against risk of electrical shock do not put house body in water or other liquid.

•Close supervision is necessary when any appliance is used near children.

•Unplug from outlet while not in use, before putting on or taking off parts, and before cleaning.

•Avoid contacting moving parts. Never feed food by hand. Always use food pusher.

•Do not operate the appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. Return

appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment.

•The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury.

•Do not use outdoors, household use only.

•Do not let cord hang over edge of table or counter.

•Do not use fingers to scrape food away from discharge disc while appliance is operating. Cut type injuries may result.

•This appliance has a polarized plug (one blade is wider than the other) to reduce the risk of electric shock. This plug will fit in a polarized outlet

only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug

in any way.

•SAVE THESE INSTRUCTIONS.

Meat Grinder – MG900

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Meat Grinder – MG900

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Meat Grinder – MG900

Table of Contents

Safety .............................................................................................................................................................2

Safety Symbols...........................................................................................................................................................4

Parts Identification .......................................................................................................................................7

Assembly.......................................................................................................................................................8

Operation.......................................................................................................................................................9

Mincing / Grinding.......................................................................................................................................................9

Unblocking the Appliance ...........................................................................................................................................9

Making Kibbe ..............................................................................................................................................................9

Making Sausages .....................................................................................................................................................10

Disassembly and Cleaning ........................................................................................................................11

Specifications .............................................................................................................................................11

Meat Grinder – MG900

Parts Identification

No. Name No. Name

1 Kibbe set 13 Mincing head

2 Kibbe plate 14 Food dish

3

Sausage attachment set

15

Mincing head attachment hole

4

Sausage attachment (large)

16

Locker

5

Sausage attachment (medium)

17

Reverse button

6

Sausage attachment (fine)

18

OFF button

7 Mincing plate (medium) 19 ON button

8 Locking ring 20 Main body

9 Mincing plate (fine) 21 Plug and cord

10

Mincing plate (large)

22

Hopper plate

11

Cutting blade

23

Mandrel / Food pusher

12

Shaft

EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF

Meat Grinder – MG900

Assembly

BEFORE FIRST USE: Check if the voltage indicated on the rating label corresponds to the mains

voltage in your home. Wash other parts except for the body (motor housing) in warm soapy water. 

Before plugging in, ensure the rotary button is in the OFF position.

1. Hold the mincing head

and insert it into the

housing as shown (fig.

1), then press the

locker. Next, move the

mincing head anti-

clockwise to fasten it

tightly to the main body

(fig. 2).

2. Insert the shaft into the

mincing head, long end

first, and turn to feed

the shaft slightly until

it’s set firmly in the

mincing head (fig. 3).

3. Place the cutting blade

onto the mincing head

with the blade facing

the front, as shown (fig.

4). If it’s not fitted

properly, meat will not

be grinded.

4. Place the required

attachments (mincing

plate, sausage tube,

etc.) against the cutting

blade (fig.5).

5. Hold the attachments in

place, then screw on

(rotate right) the locking

ring firmly by hand. Do

not overtighten (fig. 6).

6. Insert the hopper plate

on top of the mincing

head and push it down

so it’s firmly attached

(fig. 7).

After assembling the meat

grinder, place the unit on a flat, stable surface. Air passage around the motor housing should be kept clear and

unblocked.

EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF

Meat Grinder – MG900

Operation

Mincing / Grinding

Always use the appliance on a firm work surface. • Ensure that all appliance vents are not

blocked. • Always use the mandrel / food pusher to insert food into the appliance – never use

your fingers or other implements in place of the mandrel.

1. Before mincing, cut all food into pieces that will easily fit through the hopper feed tube (approximately 20 x

20 x 60mm is a recommended maximum). For best result, meats should be free of bone, sinew and fat.

2. Connect the appliance to the electrical supply and press the ON button to start the motor.

3. Place the food pieces into the hopper plate and use the mandrel to push it down through the feed tube.

When inserting food, try and be consistent with your feed rate and do not overload the machine.

4. After use, press the OFF button, then disconnect it form the electrical supply before disassembling, cleaning

and storing.

Unblocking the Appliance

If the mincing head becomes blocked:

1. Stop the appliance – press the OFF button and allow at least 30 seconds for the motor to cool.

2. Press the reverse button as required – food pieces may be pushed out through the hopper feed tube.

Release the button to stop the reverse function.

3. Disconnect the appliance from the electrical supply, then disassemble the mincing attachments and feed

screw, and clean/unblock them as required before using the appliance again.

Making Kibbe

Stuffing Recipe

Mutton 100g

Olive oil 1 ½ tbsp.

Onion (cut finely) 1 ½ tbsp.

Spices to your taste

Salt to your taste

Flour 1 ½ tbsp.

1. Mince mutton once or twice.

2. Fry onion until brown and add minces mutton, all spice, salt and flour.

Shell Recipe

Lean meat 450g

Flour 150-200g

Spices To taste

Nutmeg (cut finely) 1

Powdered red pepper to Taste

Pepper To taste

EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF

Meat Grinder – MG900

1. Mince the meat three times and mix all ingredients together in a bowl. Use more meat and less flour for

outlet cover to create better consistency and taste.

2. Grind the mixture three times.

3. Disassemble the unit by reversing steps 5 – 3 above and remove the mincing plate and cutting blade.

4. Place kibbe attachments onto the mincing head together, fitting the protrusions into the slots (fig.8).

5. Screw locking ring into place until tight. Do not over tighten (fig.9).

6. You can now make the shells (fig.10).

7. Form the kibbe as illustrated below and deep fry.

Making Sausages

1. When assembling the mincing head, insert the sausage tube.

2. Place the sausage skin on to the sausage tube and pinch or tie off the end of the skin.

3. Begin mincing. Use your fingers to hold the sausage skin, feeding it out so that the skin is adequately filled

but not to the point of bursting.

EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF

Meat Grinder – MG900

Disassembly and Cleaning

IMPORTANT! Do not wash this product or its parts in a dishwasher. Cleaning in a dishwasher

can damage the product and its parts.

•Make sure that the motor has stopped completely.

•Disconnect the plug from the power outlet.

•Disassemble the machine:

1. Pull the hopper off from the top of the mincing head.

2. Unscrew the locking ring (rotate left) and remove it.

3. Remove the attachments (sausage tube, mincing plate etc).

Note that it may be necessary to use a lever (screwdriver

etc) to pry the mincing plate from the end of the mincing

head.

4. Pull the cutter and feed screw from the mincing head tube.

5. Loosen (rotate left) the mincing head locking screw and

rotate the mincing head so that the arrows on it and the

machine body are aligned, then pull the mincing head from

the machine body.

•Remove all food particles from the parts.

•Thoroughly wash all parts (NOT the appliance body) in warm

soapy water, rinse and dry. Do not use bleach, caustic or harsh

solvents or abrasive as these may damage the surface finishes

or present a poison hazard.

•Lubricate the feed screw and attachments lightly with vegetable

oil.

•If required, clean the appliance body with a damp cloth. Do not use detergents or chemicals.

The appliance features a pressure relief valve for the motor

on top of the body. Occasionally, a small amount of oil may

be released through the valve – this is normal. Clean any oil from the valve

area. Ensure that food does not come into contact with any oil from the

appliance. When you receive the meat grinder, the relief valve comes in a

red, plastic screw (A) to prevent oil leakage when the meat grinder is in

transit. Please replace it with the metallic screw (B) provided in the

packaging once you have received and set-up your meat grinder.

Specifications

Material Brushed Aluminium body

Voltage 240V - 50/60Hz

Max. Power 2500W

Certifications SAA, CE and GS

Power Plug Australian Standard

A

B

EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF EUROCHEF

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Euro Chef MG900 User manual

Popular Meat Grinder manuals by other brands