EURO One Assembly instructions

Operator’s Instructions
Intruder Alarm System
NE NEplus
&
Euro-MERiDIAN

Page A1
You’ve Made the Right
Choice
Contents
Introduction A1-4
Using Euro-MERiDIAN with Code or Tag B1-5
Intelligent Setting B6-7
When Problems Arise C1-3
Setting Individual Area D1-3
Chime Facility E1
Omitting Zones E2-3
Keypad Personal Attack E4
Manager Menu F1-2
Omitting 24 hr Zones F3
Changing Date & Time F4
Change/Add Codes or Tags F5-10
Review History Log F11-12
SMS Phonebook F13
Walk Testing Detectors F14
Testing your Sounder F15
SMS Messaging System F16-17
Dial Out Menu F18
Allow Engineer Menu F19
Block Remote Set F20
Perform Anti-Code Reset F21
Service & Codeholder Records G1-2
Note the specification of Euro-MERiDIAN may vary
between models, and some facilities in the manual
may not be available. Check with your installer for full
details. This equipment may be used in systems
installed to a lower grade, which will be agreed with
your installation company.
© Castle Care-Tech 2006 (RINS1020) Issue 1

Page A2
You’ve Made the Right
Choice
Using your Euro-MERiDIAN Alarm
System just couldn’t be easier!
This is the Keypad from where
you control your Alarm
System*.
Note:
For your security, the keypad becomes
disabled for 90 seconds after 24 incorrect key-
presses, or after 6 attempts to present invalid
tags. It will subsequently be disabled again
after 7 further incorrect key-presses or after
another invalid tag is presented. Once a
correct code or tag has been registered, the
keypad is returned to normal operation.
*Please note that Keypad design may differ from that shown.

Page A3
The MERiDIAN Keypad
The display gives you any
important messages. It will alert
you if you need to call your alarm
installation engineer.
The 10 digit numeric keypad is
where you use your PIN code.
The A B C D keys help simplify use,
and will illuminate to highlight
your choice of security cover, or
flash if there is a problem.
This is where you present your
Tag .
MERiDIAN
TIME
:
MAINS
FAIL

Page A4
Warning Indications
All setting points (Keypads or Tag
Readers) have lamps to clearly
indicate what is happening.
The ‘Alert’ lamp will flash if there is
information available to you. Enter your
code to see the information. After a code
has been entered, one of the following
lamps will light: Alarm, tamper or fault.
The relevant detail of the problem will be
shown on the display. To clear the
display, press the ‘Yes’ key (or the display
will clear automatically after 3 minutes.)
The ‘Alarm’ lamp will flash after code
entry if an alarm occurs.
The ‘Tamper’ lamp will flash after code
entry if the wiring or equipment is
tampered with.
The ‘Fault’ lamp will light after code
entry to indicate if a technical fault
occurs.
The ‘Unset’ lamp will light for 5 seconds if
the panel is completely Unset (steady) or
if some areas remain Set (flashing). It will
also light during the setting procedure,
going off once set.
Alert Alarm Tamper Fault Unset

Page A5
Using Tags
Euro-MERiDIAN’s High Security
Proximity Tag (or Card) will set or
unset your Alarm system with the
minimum of fuss or complexity.
The Tag contains NO batteries and
is completely maintenance free.
Just touch the Tag to the fascia
below the logo to use.
The Keypad will BEEP to
acknowledge the TAG.

Using the
Keypad with
your PIN
Code or

Page B1
Security Checks
Before you set your system:
You must ensure all doors and
windows are securely closed and
any pets or people are excluded
from areas protected by
movement sensors.
Close Windows
Close Doors
Exclude Pets & People

Page B2
Leaving the Building
If you are leaving the building, go
to Keypad and key in your PIN
code, or present your Tag.
Exit tone Starts
The appropriate area (ABCD) keys
will illuminate.
(If flexi-set is enabled you will be able to
choose which areas you set, see page D2)
Leave by agreed Exit Route
Close and Lock the Final Exit
Door
Finally, press the ‘Push to Set’
button (if fitted) that is mounted
externally by the final exit door.
Exit tone will cease
Euro-MERiDIAN is now SET
SETTING [009]
OFFICE
Exit Timer
If your exit is timed,
you will see the above
screen.
If you use a Push-to-Set
button, or final-door-
set, you will see the
screen below.
MERiDIAN
TIME
:
L
eave v
i
a
Exit Route

Page B3
Faults when you Switch On
If when you key in your PIN code
(or present your Tag) a warning
tone sounds and the
fault lamp
comes on, the keypad display
will show the nature of the
problem.
An appropriate
A B C D key will
flash to indicate within which
area the fault exists.
The tone will cease after about
10 seconds.
Press the NO key
The system will remain unset, so
you can resolve the problem.
For example, you may have left a
door open, if so, close the door.
Now commence the setting
procedure again.
UNABLE TO SET
BACK
DOOR

Page B4
Faults when Leaving the
Building
If when you have closed the final
exit door (and pushed the
‘Push
to Set’
button if fitted ), the exit
tone continues to sound an
interrupted tone…
“beep – beep – beep – “
You have probably left a
protected door on the exit route
open.
Return to the keypad and note
the message on the display.
Stop the setting procedure with
your PIN code, or Tag.
Close the open door
Now commence the setting
procedure again (see B2).
EXIT VIA
HALLWAY

Page B5
Entering the Building
To enter the building you
must
use the agreed entry route and
go straight to the keypad.
Entry tone will be sounding
“beep – beep – beep –“
Key in your PIN code, or present
your Tag.
Entry tone will cease
To indicate that the system has
unset, the unset lamp will
illuminate for five seconds.
Euro-MERiDIAN is now UNSET
ENTRY [010]
TIME
**
ENTRY
[
020]
TIME

Page B6
Part-Setting the System
Intelligent Set (if programmed)
If you wish to set
Euro -MERiDIAN
and stay in the building (eg set
the alarm at night), the Euro-
MERiDIAN’s intelligent operating
system will realise which level of
security you require and will set
only part of the system.
You will NOT need to press a
Push-to-Set button if you set
only part of a system.
If intelligent set is not installed
on your system, you may part set
the system as described on
Pages D1-D2.

Page B7
Staying in the Building
Intelligent Set
To Part Set
Euro -MERiDIAN go to
the keypad and enter your PIN
code or present your Tag.
The appropriate
A B C D keys will
illuminate
Exit tone will start
Leave the protected area and
retire to the un-protected area
(eg upstairs).
Euro-MERiDIAN will detect you
have gone upstairs and set the
appropriate areas accordingly.
After a preset time the exit tone
will cease.
Euro-MERiDIAN is now Part Set

When
Problems
Arise, Just
Key in your
PIN Code or

Page C1
Silencing Alarms
If an Alarm tone sounds, the
Alert lamp will flash:
Just key in your PIN code or
Present your Tag.
The Alarm will stop sounding
The display will indicate the
problem.
Press the
‘YES’ Key
Euro-MERiDIAN will advise you on
any action that is needed. If the
‘Alert’ LED indication remains lit,
there is additional information
available. Enter your PIN or
present your Tag to view.
Call Engineer
Low Volts
Alarm Silenced
Low Volts

Page C2
Engineer Reset
When an alarm has been cancelled and
the Police have been notified by the
Alarm Receiving Centre, you will see the
following screen when you try to use
the system.
It is usually necessary for an engineer
from your installation company to
check the installation and reset the
system for further use.
But if you have
caused the alarm in error
your Alarm
Receiving Centre or Alarm Installation
Company may permit you to reset the
system without an engineer present.
You will be required to quote a 6-digit
code by telephone (advise them that
the system is a Castle Euro-MERiDIAN).
You will then be given a special code
which will reset the system
for that
one occasion
only.
Press ‘NO’
Enter the anti-code given to you by
your installation company.
You alarm in now restored and ready to
use.
This 6-digit code is also displayed in the
‘user menu’ – see page F21.
Q
uo
t
e
G19867
Anti-Code Needed
E
uro
-
MERiDIAN
TIME:
E
ng
i
neer
R
es
t
ore
Performed
Q
uo
t
e
G19867
Anti-Code Needed
E
n
t
er your
C
o
d
e
[* ]

Page C3
Automatic Inhibit
Euro-MERiDIAN is designed to
automatically disable certain
functionality. The factory default
settings are as shown below:
Intruder
Alarm Signal
After 3* unconfirmed
alarms in the same area or 1
confirmed alarm.
Tamper
Alarm Signal
After 3* unconfirmed
alarms in the same area or 1
confirmed alarm.
Keypad After 23 keypresses without
entering a valid code, keys
are disabled for 90 seconds.
After reinstatement, this will
be repeated after each 7
keypresses until a valid code
is entered.
Tag Reader
(or Tag at a
keypad)
After 6 presentations of an
invalid tag, the reader will be
disabled for 90 seconds. After
reinstatement, this will be
repeated for each invalid tag
until a valid tag is used.
* This figure is programmable by the
installing company

Setting
Individual
Areas

Page D1
The A B C D Keys
Sometimes your security needs
will be a little more complex and
you will need to use the
A B C D
keys.
Your Installer can also give
names to all four of the
A B C D
areas, so that you can easily
identify them.
For example:
A =Reception or A ll Set
B =Warehouse B edtime Set
C =Office C at in Lounge
D =Storeroom D og in Study
In addition, names can be given to
the whole system
‘ALL AREAS’
These will be displayed when
setting the system.
MERiDIAN
TIME
:
MERiDIAN
TIME
:
SETTING
ALL AREAS