Eurolux F12B User manual

3 Blade Industrial Ceiling Fan
F12B / CH / W
PRODUCT CODE
12
Mounting Bracket
Slotted Hole
Round Hole
Insert downrod into downrod yoke. Make sure to align
hole in downrod with the hole in downrod yoke.
Lift canopy and install yoke cross pin through yoke
downrod.
Insert clamp pin into cross pin until it snaps into place.
Tighten of set screw in yoke.
3
Clamp
Pin
Cross
Pin Set Screws
4Follow diagram above to connect wires.
Make sure that all exposed wiring is secured inside the
terminal block.
5
From Fan:
4 Pole
Connector
L - Block
N - Block
- Block
From House:
Power Supply
Neutral
Earth (Yellow/Green)
7
Carefully lift fan from mounting plate hook, making sure not to
break any wire connections. The canopy has 2 mating slots and 2
mating holes (see illustration). Position both slots in canopy
directly under and in line with 2 mounting plate screws and lock
washers lift fan until mounting plate screws are seated in
bottom of slots in canopy. Rotate clockwise until both
mounting screws drop into slot recesses. Tighten screws
securely. Install third and fourth screws with lock washer
into mating holes and tighten.
Mounting Slots
Mounting Slots
After fan is installed tighten Attach blades to top of motor using screws and
washers shown above.
true-balance canopy bolts with pliers or wrench to
eliminate wobble during operation.
NOTE: Over-tightening bolts may damage canopy.
8
DOWNROD INSTALLATION ONLY
9
ATTACHING THE BLADES
WALL CONTROL INSTALLATION WIRING GUIDE
Insert downrod and ball assembly into large opening in
canopy, making sure canopy tab engages notch in
downrod ball. Place true-balance clamp ring over down-
rod ball and install 3 true-balance bolts through the
bottom of the canopy and into clamp ring.
(These bolts will be tightened correctly in step #9) .
6
Clamp Ring
Canopy Tab
Ball Notch
1
2
3
Two Wires are required to operate the fan from the wall control.
1) “Actile” wire form lighting circuit of the fuse box, connected to
terminal A on the wall control.
2) “Fan Active” wire from the fan connects to F on the wall control.
10
L
3 2
1
AØ F
NOTE: Flushmouting will not require the downrod.
shock.
components
ENVIRONMENTAL PROTECTION
Waste electrical & Electronic equipment regulations requires that any of our products showing this
marking must not be disposed of with other household or commercial waste. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate any
such products from other waste types and recycle it responsibly at your local facilities.
ILLUSTRATIONS
Please read instructions before commencing installation and retain for
future reference.
Cape Town - 9 Racecourse Road, Milnerton, 7441
Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065
email: [email protected], web: www.eurolux.co.za

SPECIFICATIONS
F12B / CH / W attachments:
If the external exible cable or cord of this luminaire is damaged, it should be exclusively replaced
by the manufacturer or his service agent or a similar qualied person in order to avoid a hazard. To
ensure that you get maximum longevity and maximum use out of your luminaire, please observe
the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire
must be carried out by a qualied electrician, in accordance with SANS 10142. On completion
of installation, ensure that the Certicate of Compliance is updated.
• Before connecting this fan, ensure that voltage indicated on the rating label corresponds with
the mains voltage in your home.
• When cleaning, ensure that the power is turned off.
• This fan is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons,
caused by the incorrect use or installation of the fan.
• Should you be unsure of how to install this fan correctly, please consult a professional
electrician or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this fan, I.E. Using silicon sealers or incorrect cabling, will invalidate your
warranty. If one is not supplied within the carton, DO NOT use a solid speed control.
• Each blade set supplied is weighted and a complete set. If installing more than one fan,
DO NOT mix or add blades as this can cause your fan to wobble.
• Please check whether the connection of the power cord is safe and reliable before installation.
• Always ensure that the mains supply voltage is correct.
• Do not use the fan outdoors, in wet conditions or areas of high humidity.
• Do not insert objects or ngers through the bars of the grill.
• Always unplug the fan when cleaning or moving from one location to another.
• Always ensure that the fan is on an even, stable surface.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible
for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
IMPORTANT SAFEGUARDS
• The fan is operated by pull wall control:
High Speed
Medium Speed
Low Speed
Off
• Note: Fans move during operation which may cause some connections to come loose.
Check the supporting screws, brackets and blade attachments twice a year to ensure they are secure.
OPERATION
CLEANING
• Before cleaning always ensure the power supply is turned off and that the fan has been unplugged.
• Do not immerse the fan in water.
• No abrasive products, solvents, detergent may be used to clean this fan.
• Ensure that the fan does not come in contact with corrosive chemicals, etc.
• The motor bearings are permanently sealed and do not require additional lubrication.
•FittingMaterial: Pressed Steel
•Motor: 60W
•Voltage: 220 - 240V~ 5060Hz
•Protectionagainstelectricshock: Class 1. Requires earth connection
•IPRating: 20. Protected against solid foreign objects of 12.5mm Ø and greater, not protected
against water.
• Not for outdoor use or in wet conditions and areas of high humidity.
•Dimensions: (H)340mm x (Ø)1220mm
•Features: 3 Speed
•NumberofBlades: 3 Blades
Wall controller
2 Years Warranty
TROUBLE SHOOTING
CAUTION: Ensure power supply is turned off before attempting trouble shooting.
NOTE: This fan does not contain serviceable parts. DO NOT OPEN or TAMPER WITH THE MOTOR.
Should your fan not start:
1) Check fuses are in place in the switchboard.
2) Recheck the terminal strip connections.
3) Ensure the wall & direction switches are not stuck in a “middle” position. Should your fan be noisy:
1) Check all screws are sufciently tight: fan blades and fan holders, (if applicable) glass of the lamp
holder.
2) Allow at least 24 hours for the fan to settle.
Should your fan wobble:
In general, wobble is caused by the blades not cutting the air at the same point. Measure downwards
from the ceiling and make sure each blade is at the same height to the ceiling. See Figure 1. If they
are not, adjust by hand by slightly bending the blade and bracket.
If a major adjustment is needed, insert a washer as shown in Figure 2.
1) Check the blades are securely fastened to the holders.
2) Check the blade holders are tight on the motor.
3) Ensure the mounting bracket is properly screwed to the ceiling.
4) Interchange opposite blade sets if needed.
Should the light on your fan not work:
1) Check the terminal connections are tight.
2) Check if the lamp is blown.
Should the above fail, contact a qualied electrician for assistance.
Touching
Ceiling
Figure 1 Figure 2
Blade Brackets
Blade Tip Down:
Fan Blade
Blade Tip Down:
Fan Blade
Fan Wobbles: