Euromatic DF-EF1050AG2 User manual

Model Number DF-EF1050AG2
INSTRUCTION MANUAL
AFTER SALES SUPPORT
(AU) 1300 886 649 (NZ) 0800 836 761
AIR CIRCULATOR
Heating and Cooling

2After Sales Support
1300 886 649 | [e-mail]
Contents
03 Important Safety Instructions
06 Product Overview
08 Getting Started
09 Instructions
14 Other Useful Information

3
After Sales Support
1300 886 649 | [e-mail]
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this type
of product. The safety precautions enclosed herein reduce the risk of fire, electric
shock and injury when correctly adhered to. Make sure you understand all instruc-
tions and warnings. Keep the manual in a safe place for future reference, along with
the completed warranty card, purchase receipt and packaging. If you sell or transfer
ownership of this product, please pass on these instructions to the new owner.
Always follow basic safety precautions and accident prevention measures
when using an electrical appliance, including the following:
Electrical safety and cord handling
• Voltage: Before plugging in the appliance, make sure your outlet voltage and
circuit frequency correspond to the voltage stated on the rating label.
• Electrical circuit: Always plug this appliance into a separate wall outlet socket.
Use a safe socket with an earthed connection. To ensure you do not overload
the circuit, do not operate another high-wattage product on the same circuit.
• Connection: To insert the plug, grasp it firmly and guide it into the outlet.
• WARNING! No no extension cord: Do not use the appliance with a power
board, adaptor or extension cord, as these may overheat and create a fire risk.
• Protect the power cord:
– Do not operate the appliance with the cord coiled up; always fully unwind.
– Do not twist or kink the cord or let it touch heated surfaces.
– Do not put any stress on the cord where it connects to the product.
– Never pull/carry the appliance by the cord.
– Never place the cord under the appliance. Arrange the cord away from any
traffic areas so no one will trip over it.
– Do not run the cord under carpeting or cover it with rugs, runners, etc.
• WARNING! To reduce the risk of fire, electric shock or injury:
– Never touch the appliance with wet or damp hands or feet.
– Do not use the appliance if any part of it has become wet. Immediately call a
qualified service technician to inspect the appliance and replace any part of
the electrical system that has got wet.
– Never spill liquid into the appliance; never immerse the cord, plug or any part
of the appliance in water or other liquids.
– Do not reach for an appliance that has fallen into water. Switch off and unplug
immediately.
• Damaged cord: Check the power cord regularly for visible damage. If the cord
is damaged, it must be replaced by the manufacturer or appropriately qualified
personnel in order to avoid any hazards.
• WARNING! Damaged heater: Do not use this appliance if there are visible signs
of damage to the appliance, after it malfunctions, or after it has been dropped or
damaged in any manner.
Important Safety Instructions

4After Sales Support
1300 886 649 | [e-mail]
Important Safety Instructions (Cont.)
• Plug: It is normal for the plug to feel warm; however, a loose fit between the AC
outlet and plug may cause overheating and distortion of the plug. Contact a
qualified electrician to replace a loose outlet.
• After use: Switch off the appliance at the rocker switch and unplug it from the
power outlet when it is not in use and before cleaning, servicing, moving or
storing the appliance. To disconnect, switch off the appliance, then remove the
plug from the outlet. Grip the plug, do not pull the cord.
• Safety switch: Unless your home is already fitted with a residual current device
(safety switch), we recommend installing an RCD with a rated residual operating
current not exceeding 30mA, to provide additional safety protection when using
electrical appliances. See your electrician for professional advice.
Usage conditions and restrictions
• Domestic use only: This appliance is intended only for use as a heater or
cooling fan in indoor living spaces and only for domestic use. It is not suitable
for commercial, industrial or trade use.
• Space heating only: Do not use the appliance for drying or heating clothing,
shoes, pipes or any other item, or for any other purpose. Only use it as
described in this manual. Any other use may cause fire, electric shock or injury.
• No outdoor use: Do not use this appliance outdoors or on wet surfaces.
• Protect from moisture: This appliance is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never locate this appliance where
it may fall into a bathtub or otherwise become exposed to water. Never place
containers filled with liquid, such as drinking glasses, vases, etc. on the appliance.
• Ventilation: Only use this appliance in a well ventilated area.
• Keep openings clear: To prevent a possible fire, do not insert or allow objects,
or fingers, to enter any ventilation or exhaust openings. Do not block air intake
or outlet openings in any manner.
• WARNING! No external timer: Never operate the appliance on a program switch,
external timer switch or any other appliance for automatic operation, as there is a
risk of fire if the appliance is covered or positioned incorrectly. In order to avoid a
hazard due to inadvertent resetting of the thermal cut-out, do not connect it to a
circuit that is regularly switched on and off by your energy provider.
• WARNING! This appliance is not equipped with a device to control the room
temperature. Do not use this appliance as a heater in small rooms when they
are occupied by persons not capable of leaving the room on their own, unless
constant supervision is provided.
• Children should be supervised to ensure that they do not play with the
appliance. Close supervision is necessary when any appliance is used by or
near children. Do not let children operate this appliance.
• WARNING! Do not leave unattended during use.

5
After Sales Support
1300 886 649 | [e-mail]
Important Safety Instructions (Cont.)
WARNING! Do not cover!
In order to avoid overheating and creating a fire risk,
do not cover the heater in any manner.
• Usage restriction: This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been given supervision or instruction con-
cerning the use of the appliance by a person responsible for their safety.
• Location: Place the appliance on a horizontal and stable surface; do not place it
on a soft surface such as on a bed, sofa or long pile carpet, as this could cause
the appliance to tip over.
• Do not use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
• WARNING! To avoid creating a fire risk, do NOT use this appliance:
– In front of or immediately below an electrical socket outlet
– Close to a radiant heat source
– Behind a door
– On long pile carpet or a flokati rug
– Near a window where it may get splashed with rain
– In areas where petrol, paint or other flammable liquids are stored (e.g. in a garage
or workshop), as the heater has hot and arcing parts inside which may spark
• WARNING! To reduce the risk of fire, keep textiles, curtains, or any other
flammable material a minimum distance of 1m from the air outlet. Do not place
towels or other objects on the heater.
• CAUTION! Personal safety: Avoid contact with moving parts. Never insert
fingers, pencils or any other objects through the grilles when the appliance is
running. Keep hair and loose clothing well away from the product when it is in use.
• CAUTION: Hot! In heating mode, some parts of this appliance can become very
hot during use and remain hot for some time afterwards. To avoid burns, do
not let bare skin touch hot surfaces. Be particularly careful when children and
vulnerable persons are present. Always let the heater cool down before touching
it, even if it is unplugged.
• Misuse: Improper use or installation may result in the risk of fire, electric shock
and/or injury. We accept no responsibility for any eventual damage or injury
caused by improper use or incorrect handling.
• Service: This appliance contains no user-serviceable parts inside. Do not
attempt to open and/or repair the appliance yourself. Components should only
be serviced by a qualified technician. In case of malfunction, disconnect the
plug immediately and contact our after sales support centre for advice.
• Assembly: This product comes fully assembled. It cannot be used without a
base and must be placed horizontally for operation.

6After Sales Support
1300 886 649 | [e-mail]
Product Overview
Air circulator - heating and cooling
1 Front grille
2 Blade (behind the grille)
3 Upper base
4 Control panel with LED display (see page 7 for details)
5 Lower base
6 Remote control
7 ON/OFF switch
8 Dust filter (behind the rear cover)
9 Rear cover
Angled front view
Angled rear view
Documentation (not shown)
Instruction manual
Warranty certificate
Scope of delivery
7
1
2
3
4
5
6
9
8

7
After Sales Support
1300 886 649 | [e-mail]
Product Overview (Cont.)
NOTE: Due to continued product improvement, images and illustrations in this manual
may vary slightly from the product purchased. All images in this manual are for
reference purposes only. They are not necessarily pictured to scale.
Remote control
Control panel
Operation buttons and indicators
Power/Standby
Wind speed adjustment: strong, high, medium, low
Timer: 1h, 2h, 4h, 8h
Oscillation: motorised horizontal swing around 80 degrees;
manual tilt upward around 90 degrees
Heating: High (2000W), Low (1000W), Eco
Sleep mode (in Fan mode only)
46

8After Sales Support
1300 886 649 | [e-mail]
Getting Started
Unpacking
• Packaging: This product has been packaged to protect it against
transportation damage. Unpack the appliance and keep the original packaging
in a safe place. It will help prevent any damage if the product needs to be
transported in the future, and you can use it to store the appliance when it is
not in use. In the event that the packaging is to be disposed of, please recycle
it where possible.
• Plastic wrapping can be a suffocation hazard for babies and young children,
so ensure all packaging materials are out of their reach and disposed of safely.
• Check for damage: Visually inspect the power supply cord and plug, and
all other parts of the appliance, for damage. Check and ensure that no
foreign material is blocking the air inlet and outlet. Do not use the appliance
if anything appears to be damaged or not working properly.
• Documentation: Make sure you have read and understood all instructions
and warnings in this manual. Refer to the Product Overview on pages 6–7
to familiarise yourself with the product and identify all parts. Pay particular
attention to the safety instructions on the previous pages.
• Assembly: The appliance comes fully assembled.
Using the remote control
• The appliance comes with a remote control, which is powered by a CR2032
3V lithium button cell (supplied inside). Before use, please pull out the small
plastic flap that separates the contacts.
• During use, point the remote control towards the infrared receiver at the front
of the appliance. Make sure there are no obstructions along the path of the
signal as these will hinder the performance of the remote.
• Handle the remote control with care. Do not drop it to the ground.
• The remote control may be placed in the holder at the back of the appliance
for easy accessibility.
WARNING!
Keep batteries out of reach of children. Swallowing may lead
to serious injury or death in as little as 2 hours due to internal
burns. If swallowed, go straight to a hospital emergency
room. Dispose of used batteries immediately.

9
After Sales Support
1300 886 649 | [e-mail]
Instructions
Features
• The appliance can be operated as a heater or as a cooling fan.
• It can be operated either manually using the control panel on the upper base,
or remotely via the supplied remote control.
• The appliance is equipped with four wind speeds
(strong, high, medium, low), an off-timer with four
settings (1h, 2h, 4h, 8h), and horizontal oscillation
(80°). It can also be manually tilted upwards 90
degrees, as pictured.
• When used as a heater, you can select a low
(1000W) or high (2000W) heat setting.
Set-up location requirements
• Place the heater in an upright position on a flat,
stable, dry and heat resistant surface, taking into
consideration all relevant safety information on
the previous pages. Make sure it is not subject to
vibrations or movement.
• To exclude the risk of fire, maintain minimum clearances of 50cm above,
behind and at each side of the heater, and 100cm at the front.
• Do not place the appliance in a hot, wet or very moist environment, or in the
vicinity of flammable materials.
• The mains power socket must be easily accessible so that, in an emergency,
the mains power cable can be easily disconnected.
• Select a location where the flow of hot air is not directly aimed at people,
animals or plants.
First use
When turning on the heater for the first time, it is normal for the heater to emit
a ‘new heater’ smell, or a little smoke. This is not harmful and will stop after a
short while. Please ensure meanwhile that there is sufficient ventilation.
Connection
• Make sure the ON/OFF [ I / O ] switch at the back of the appliance is in the
OFF [ O ] position, then plug the mains plug into an appropriate electrical
outlet and switch on power to the outlet.
• Always use a separate socket that has no other high wattage appliances
connected at the same time – do not plug it into a power board or socket
adaptor; do not use an extension cord.

10 After Sales Support
1300 886 649 | [e-mail]
Instructions (Cont.)
Wind speed
On first starting up, the appliance runs in low gear and on the LED display,
the wind speed indicator and [ 1 ] are shown.
• Press the WIND SPEED button, repeatedly, to increase the speed to
medium [ 2 ], high [ 3 ] or strong [ 4 ], and then back to low [ 1 ]. The LED
display will show the wind speed indicator and the corresponding
numbers.
Timer
The heater has an eight-hour timer with which you can set the required
operating time for 1 hour, 2 hours, 4 hours or 8 hours. The appliance switches
off automatically once the operating time has expired. You can set the timer
when the appliance is operating.
• Press the TIMER button, repeatedly, to set the required operating time:
1h, 2h, 4h or 8h hours. The respective indicator will illuminate.
• If you have set a 4h timer, after two hours have elapsed, the [ 4h ] indicator
will change to the [ 2h ] indicator. At the end of the set operating time, the
appliance will switch to standby automatically.
Switching on/standby
• Set the rocker switch at the back of the appliance to the ON [ I ] position to
set the heater into standby mode. Once electricity is supplied, the heater will
emit two short beep sounds.
In standby mode, only the POWER/STANDBY button will be operational.
All other buttons will be ineffective.
• Press the POWER/STANDBY button (on the remote control or control
panel) to switch on the heater. It will start in default mode (low wind speed,
no heat, no swing, no timer).
• When the heater is operating, press the POWER/STANDBY button to
switch the heater to standby. It will continue to run and then switch to
standby after a few seconds.
NOTE: The appliance will continue to consume power in standby mode.
• To switch the appliance off completely, set the rocker switch to OFF [ O ] and
unplug the cord from the power supply.
LED indicators
All indicators will be dimmed 80% when there is no operation for one minute.

11
After Sales Support
1300 886 649 | [e-mail]
Instructions (Cont.)
Oscillation (swing)
The appliance has an oscillation (swing) function, which you can set to help
distribute the air over a larger area. It will work in any mode. Always switch off
the oscillation function before you tilt the appliance upwards and before you
switch off the appliance.
• Switch on the appliance and select the wind speed, as described
previously.
• To start oscillation, press the OSCILLATION button.
• While the appliance is oscillating horizontally, press the OSCILLATION
button to stop oscillation.
Heating
The appliance can be operated on two power levels for heating (1000W or
2000W), or in ECO mode, where the appliance automatically selects the
appropriate setting.
• Low (1000W):
Press the HEATING button for the first time to run the appliance on
the low (1000W) heat setting. The heating indicator will illuminate on the
display and the appliance will start running with medium [ 2 ] wind speed.
• High (2000W):
Press the HEATING button a second time to run the heater on the
high (2000W) heat setting. The heating indicator will change position and
the appliance will start running with high [ 3 ] wind speed.
• ECO: Press the HEATING button a third time to run the heater on the
ECO setting. On this setting the appliance works automatically:
– When the room temperature is below 18°C, the appliance will run on the
high (2000W) heat setting.
– When the room temperature is between 18°C and 22°C, the appliance
will run on the low (1000W) heat setting.
– When the room temperature is higher than 22°C, the appliance will stop
running: first the heating function will stop and 10 seconds later also the
fan function.
• Turnoheating:
Press the HEATING button a fourth time to turn off the heating
function. The warm wind will stop and the appliance returns to fan only
operation (the wind speed remains unchanged in middle gear).

12 After Sales Support
1300 886 649 | [e-mail]
Instructions (Cont.)
• In heating mode:
– The product runs in the following cycle order:
cold wind / low-gear --- warm wind / high-gear --- warm wind / ECO
function --- medium speed / cold wind --- low-gear / warm wind ... ...
– The wind speed is fixed to middle gear, you cannot adjust it; pressing the
WIND SPEED button is ineffective.
– The timer and oscillation functions can work normally.
– The fan will continue to run for about 10 seconds after switching off.
Sleep function
The appliance has a sleep function, which can be selected in fan only mode.
Depending on the wind speed selected, the appliance will maintain that
wind speed for the first 30 minutes and then reduce it gradually to maintain
comfortable conditions when going to sleep.
• Press the SLEEP function button to activate this function, the
corresponding indicator will illuminate on the display.
– When you are running the fan with LOW wind speed and activate this
function, a low natural wind speed will be maintained during the night.
– When MEDIUM wind speed is selected, the appliance will run with
medium wind speed for 30 minutes before switching to low speed.
– When HIGH wind speed is selected, the appliance will run with high wind
speed for 30 minutes, then with medium speed for 30 minutes and then
switch to low speed.
• Press the SLEEP mode button to turn off the sleep function.
NOTE:
– The sleep function cannot be turned on in heating mode.
– Pressing the HEATING button while the sleep function is selected will
cancel the sleep function.
Switchingo(tostandby)
• Press the POWER/STANDBY button to switch the appliance to standby.
(If the appliance was run in heating mode, the fan will continue running for
approximately 10 seconds before coming to a standstill.)
• If you are not going to use the appliance for a while, do not leave it in
standby mode. Turn it off by setting the ON/OFF switch at the back of the
base to the [ O ] position and unplug it from the power supply.

13
After Sales Support
1300 886 649 | [e-mail]
Instructions (Cont.)
Safety features
Overheat protection and prevention
An internal overheat protection system will shut down power to the appliance
if the internal parts get too hot (above 70˚C). All indicators will extinguish and
all functions will stop. The internal temperature must have dropped to a safe
level before the heater will restart.
While this features provides additional safety in case of overheating, first and
foremost you should make sure to eliminate all potential reasons that can lead
to overheating and create a fire risk.
If the overheat protection has been triggered, switch off the appliance, unplug
it from the electrical socket and let it cool for at least 10 minutes until all
surfaces are safe to touch. Eliminate the cause of the overheating (for
example, excessive dust in the appliance, or the air outlet is covered). Start
the appliance up again. If after eliminating the cause you still cannot switch
the appliance back on, or if the overheating protection circuit switches on
without an apparent reason, please contact our after sales support centre.
IMPORTANT!
• A common cause of overheating is deposits of dust and fluff entering
the heater. Ensure these deposits are removed regularly by unplugging
the heater, allowing it to cool and cleaning it, as described in the
“Cleaning and maintenance” section.
• Also make sure that the appliance can sufficiently dissipate the heat
generated. This is particularly important in case the overheat protection
has been triggered. Ensure there is sufficient room all around the heater,
and nothing is covering or obstructing the air outlet or intake.
Tilt protection (tip-over safety switch)
This appliance is equipped with a tip-over safety switch, which switches the
appliance off in the event that it is knocked over or tilted to a position where
safe operation is in jeopardy. If this occurs, we recommend you switch off the
appliance manually before standing it upright again. Make sure to place the
appliance on a flat, level surface before turning it on again.

14 After Sales Support
1300 886 649 | [e-mail]
Other Useful Information
Battery replacement
When the button cell in the remote control needs to be replaced, pull out the
button cell holder and insert a fresh button cell with the (+) marking facing
upwards. Then push the holder with the button cell back into the unit.
General battery precautions
WARNING: Keep out of reach of children! Children often cannot assess
dangers correctly and are injured as a result. Please therefore ensure that the
remote control is kept out of children’s reach as it contains batteries. If batteries
are swallowed, seek immediate medical assistance.
WARNING: Danger of explosion! To prevent a risk of explosion, batteries
must not be charged (unless they are rechargeable ones), heated or disposed
of by burning. Never throw batteries into a fire or subject them to high
temperatures. Only dispose of batteries when they are fully discharged.
Do not dispose of used batteries in household waste. Dispose of them in
accordance with statutory regulations.
WARNING: Avoid contact with battery acid! If battery acid has leaked, avoid
contact with skin, eyes and mucous membranes to prevent injury. In the event
of contact with the acid, rinse the affected areas immediately with plenty of
clean water and contact a doctor at once.
CAUTION: Avoid damage to the appliance! Make sure to insert the batteries
correctly according to the polarity markings. Only use fresh batteries of the
required size and type. Do not open the batteries or short-circuit them. Do not
mix old and new, or different types of battery.
WARNING!
Keep batteries out of reach of children. Swallowing may lead
to serious injury or death in as little as 2 hours due to internal
burns. If swallowed, go straight to a hospital emergency
room. Dispose of used batteries immediately.

15
After Sales Support
1300 886 649 | [e-mail]
CAUTION!
• Before attempting any maintenance or cleaning the appliance, always
switch the appliance off, disconnect it from the mains power supply and
let it cool down until all surfaces are safe to touch.
• Do not attempt to open the appliance and repair it yourself. Any repairs
must be carried out by a qualified technician.
Cleaning and maintenance
To ensure your appliance gives you lasting service, you should clean it
regularly. If excessive dust, dirt or other foreign matter is clogging up the rear
parts of the appliance, its effectiveness and safety as a fan and heater will be
compromised. We therefore recommend you clean the appliance at least once
every two months.
• Switch the appliance off and allow it to cool. Disconnect the electricity
supply to the appliance.
• If the outside of the appliance needs cleaning, wipe it with a soft, damp
cloth and then wipe it dry with a dry cloth. Allow some time for the
appliance to dry thoroughly before reconnecting it to the power supply.
• Do not use caustic or abrasive cleaning powders or furniture polish, as
thiscandamagethesurfacenish.
• CAUTION: Never immerse the cord, plug or appliance in water or
other liquid for cleaning. Do not allow water to enter the interior of the
appliance.
• Dust from around the grilles can often be removed by using a vacuum
cleaner with a soft brush attachment.
• The foam dust filter at the back of the appliance can be
removed for cleaning. It sits behind the rear cover, which
can be removed by taking off the three screws at the
back of the cover.
• Shake out and clean the filter thoroughly. If washing the
filter, please ensure it is completely dry before reuse.
Reinstall the filter before refitting the rear cover. Tighten
the screws.
Other Useful Information (Cont.)

16 After Sales Support
1300 886 649 | [e-mail]
Troubleshooting
If your appliance fails to operate, or you experience any other problem with
the appliance, contact our after sales centre for advice. Before phoning for a
service, please ensure that the appliance is properly plugged in and the outlet
and circuit breaker or fuse are working properly.
Other Useful Information (Cont.)
Storage
• If you are not going to use the appliance for an extended period of time,
please unplug it at the power point.
• Clean the cool appliance as described above, then store it in a cool and dry
place, out of children’s reach.
We recommend you store the appliance in its original carton to protect it from
dust. Alternatively, cover the assembled appliance with a plastic bag or some
material to protect it from dust.
Service, repair and spare parts
If the appliance is damaged, do not attempt to repair it yourself. Do not
disassemble or modify the appliance. Except for the remote control battery and
dust filter, the appliance contains no user-serviceable parts within.
Our after sales support centre stocks spare remote controls and dust filters for
the appliance. To purchase a spare part, or if the appliance requires a service or
repair, please contact the centre using the details at the bottom of the page.

17
After Sales Support
1300 886 649 | [e-mail]
Technicalspecications
Model DF-EF1050AG2
Rated power Heating 2000W
Fan only 45W
Voltage 220–240V~, 50Hz
Dimensions (approx.) 260mm (L) × 250mm (W) × 375mm (H)
Weight approx. 4kg
Remote control button cell DC 3V CR2032
CLASS II - DOUBLE INSULATED APPLIANCE
This symbol indicates that the appliance has been designed in such a way
that it does not require a safety connection to electrical earth (ground).
Other Useful Information (Cont.)
Responsible disposal
• At the end of its working life, make the appliance unserviceable by
unplugging it from the power outlet and cutting the power cord.
• Do not throw this appliance out with your household rubbish. Electrical
and electronic products, and batteries, contain substances that can have
a detrimental effect on the environment and human health if disposed of
inappropriately. Observe any local regulations regarding the disposal of
electrical consumer goods and dispose of it appropriately for recycling.
Contact your local authorities for advice on recycling facilities in your area.
Compliance
This product has been fully tested and meets all requirements as set out by
standards AS/NZS 60335.1 and AS/NZS 60335.2.30.
The RCM Mark (Regulatory Compliance Mark) indicates that the product
complies with the relevant guidelines of the ACMA as well as corresponding
government requirements for the safety of electrical devices.
E209

18 After Sales Support
1300 886 649 | [e-mail]
This page has been left blank intentionally.

19
After Sales Support
1300 886 649 | [e-mail]
This page has been left blank intentionally.

After Sales Support
1300 886 649 | [e-mail]
Warranty returns
Should you for any reason need to return this product for a warranty
claim, make sure to include all accessories with the product.
Product does not work?
If you encounter problems with this product, or if it fails to perform
to your expectations, make sure to contact our After Sales Support
Centre on (AU) 1300 886 649 or (NZ) 0800 836 761 for advice.
Distributed by Tempo (Aust) Pty Ltd ABN 70 106 100 252
PO BOX 6056 Frenchs Forest, Australia NSW 2086
Customer Helpline:
(AU) 1300 886 649 (NZ) 0800 836 761
Email: [email protected]
For an electronic copy of this manual, please contact our after sales support centre.
IM Version No: V1.1 Issue: December 2019