Eurotops 25963 User manual

USER MANUAL
360° Turbo Fan Heater
Cat. No.: 25963
Please read this manual before using.

Warning
1. This heater is for general indoor home heating only.
2. Place heater in a well ventilated area away from flammable
materials and air cans.
3. Place the heater on a steady and even floor. Do not hang or
install on wall.
4. Please use individual socket if the output rated current is more
than 10A. Do not use the same socket with other equipment to
avoid overloading. Make sure plug is properly inserted into the
socket.
5. Supervise usage when in use with children and elderly.
6. Unauthorized disassembly, modification, repair are prohibited.
7. Do not operate or touch the plug with wet hands.
8. Use 230-240V~ AC power.
9. Ensure filters are clear and properly cleaned.
10. Do not move the heater when operating.
11. Do not cover the heater or the air vents.
12. Be careful the device will be very hot when in operation.
13. Please unplug the device when not in use.
14. Do not use any aerosols near the device when in operation.
15. If there is a burning smell, stop using and unplug the power cord.
Contact your retailer.
16. Do not use in the batch room or near water.
17. Do not allow children to play with this heater.

Product Diagram
1. LCD Display
2. Control Panel
3. Remote Controller
4. On/Off button
5. Hand grip
6. Metal gauze
7. Mica heating element
8. Power cord
Instructions
1. Remove the packaging and place on a flat and dry area.
2. Plug the heater's power cord, by using the specified connect
230-240V~ 50Hz power output.
3. Turn on the heater by pressing the On/Off button (item 4 above).
4. Insert the button battery correctly into the Remote Control

1. Power on
Plug in the power supply, press the ON button . The LCD
screen displays all the icons in two seconds . Then
entering into the standby mode, the heater will show the ambient
temperature (0-50 degrees) and a time digit 00:00 ( )
on the screen, 00:00 will keep flashing. The Mica heater is ready for
Timer setting
“+”Temperature & Timer control”up”
“-“Temperature & Timer control “Down”
“Mode”Mode setting
ON/OFF

operation.
2. Operation mode setting:
Press button on control panel or remote controller to enter
the Power Saving mode the display gives a default temperature 38℃
(flashing 2-3 seconds), then it will significantly show the ambient
temperature. Press “MODE” button to select the modes, there are
four operating modes: A) Power Saving mode, B) Sleeping mode, C)
Standard mode, D) Frosting mode; the mode selection will be
displayed for a duration of 5 seconds after pressing the MODE
button.
3. Temperature:
Press “MODE” button once to enter the temperature setting: The
temperature digit flashes, press “+”(Temperature increase setting)
and “-“(Temperature decrease setting) to adjust the temperature.
A) Power Saving/ Sleeping/ Standard modes: the default setting is
38℃which is the highest temperature you can set up to.

B) Frosting mode: the constant temperature is 7℃, the temperature
cannot be adjusted; When the room temperature is ≤ 5℃, heater
will run automatic to increase up to 7℃; When the room
temperature ≥7℃, it will stop automatically.
All mode settings will be automatically set after five seconds.
In Power Saving, Sleeping and Standards modes, when the ambient
temperature is ≤ 1℃of set temperature, heater will increase the
heat; when the ambient temperature ≥2℃of set temperature,
heater will stop.
4. Timer:
Press Timer button to enter the pre-set Timer On setting mode, the
time digit flashes. The setting time can be from (00:01) 1 minute to
(23:59) 23 Hours and 59 minutes. Press “+” button for setting the
Hour increase (1 –23 Hours) and press “-“button for setting the
Minute increase (1 –59 Minutes). After five seconds, the counting
will be started automatically. After set Timer On mode, heater will

not operate until the set time started.
In the process of pre-set Timer On or Off setting mode, you can press
button to change the heating mode.
A) Power saving mode
B) Sleeping mode ,

C) Standard mode
D) Frosting mode ; time out working is completed
after the screen display “End”, and the heater will stop. We
can always cancel the timer setting by pressing button
on control panel or remote controller.
Overheating Protection
Heater is equipped with a safety system. It will shut down when
overheat or when air vent is blocked.
Please allow the device to cool and ensure vent is clear before
turning on again.
Automatic power-off
The heater will stop when the device falls over.
Maintenance
1. Unplug the device when it requires repair or during maintenance.

2. Do not handle the device when it is still hot.
3. Gently wipe the dirt on the housing with a soft damp cloth.
4. Please do not attempt to repair the device yourself. Always
send it back to the retailers.

Possible remedial actions before contacting the retailers for repair:
Problem
Actions
Heater will
not turn on
1. Check that the device is properly plugged in.
2. Check the power source is 230-240V AC
3. Make sure the device is on a flat and horizontal
surface
4. Check if the set temperature is higher than room
temperature.
Remote
control
without
reaction
1. Remote control with low battery level
2. Out of range
3. Obstructions affecting the reception

Specifications
Voltage:
230-240V~
Frequency:
50Hz
Power:
2000W
Dimensions:
298(L) x 280(W) x 548(H)mm
G.W.(KGS)
4.8
N.W.(KGS)
3.7

DISPOSAL：
The packaging material is reusable. Dispose of the packaging in an environmentally friendly way by
putting it in the appropriate recyclable waste collection containers.
Dispose of the product and the batteries in view of the environment if you want to
separate. The device and the batteries must not be thrown in with domestic waste.
Take them to a recycling center for used electrical and electronic devices. For
more information you can consult your local government. Remove batteries first.
Eurotops Versand GmbH
Elisabeth-Selbert-Straße 3
40764 Langenfeld, Germany
If technical support is needed, please call ...
in Germany 0180 . 530 63 63* or [e-mail]
in Austria 01 . 230 60 43 12 or [e-mail]
in Switzerland 044 . 28 36 125 or [e-mail]
in the Netherlands 026 . 37 36 333 or [e-mail]
in France 0892 . 700 470** or [e-mail]
* 14 Cents/minute via German landline, max. 42 cents/minute via mobile phone network
**34 Cents/minute via French landline
A possible return of products should be addressed to the return address stated on your invoice.
The manual only reflects the technical conditions available under printing. Any changes in
technology and equipment are reserved.
© 26.04.2013