EverFocus EPN4122i Plus: User manual




EPN Series
IP Speed Dome
Quick Installation Guide


Copyright©EverFocusElectronicsCorp,
ReleaseDate:April,2013


EPNSeries
1
1. Overview
TheEPNseriesIPSpeedDomecomesintwotypes:Indoor(EPN4122i/4220i)andOutdoor(EPN4122/
4220).

No.ItemNameNo.ItemNameNo. ItemName
1TopHousing2OuterHousing 3CameraMainBody

PackingList
Themainboxcontains3largeboxesandasmallbox.Eachboxcontainstheitemsaslistedbelow.Please
checkthatthereisnomissingiteminthepackagebeforeinstalling.
Box1:Tophousingwithanetworkconnectorandtoolpacket
Toolpacket(Indooronly):Includes6PlasticAnchorsand6Screws.
Box2:Cameramainbodywithatoolpacket
Toolpacket:Includes1pairofGloves,3DesiccantPacksand1PowerTerminalBlock.
Box3:Outerhousing
SmallBox:Poweradapter
SoftwareCD
QuickInstallationGuide
Note:
1. Equipmentconfigurationsandsuppliedaccessoriesvarybycountry.Pleaseconsultyourlocal
EverFocusofficeoragentsformoreinformation.Pleasealsokeeptheshippingcartonforpossible
futureuse.
2. Contacttheshipperifanyitemsappeartohavebeendamagedintheshippingprocess.

2. SystemRequirement
Beforeinstalling,pleasecheckthatyourcomputermeetsthissystemrequirement.
OperatingSystem:MicrosoftWindowsXP/Vista(32‐bit)/7(32‐bit)
MicrosoftInternetExplorer7orabove

 EPNSeries
2
3. CablesandI/OTerminalBlock
CableDescriptions

NoNameandDescriptionsNoNameandDescriptions
1RS‐485+(Yellow):ConnectstoanRS‐485device.5AudioIn:Connectstoamicrophone.
2RS‐485‐(Orange):ConnectstoanRS‐485device.6AudioOut:Connectstoaspeaker.
324VAC~:Connectstothepoweradapter.7RJ‐45Cable:Connectstothenetwork.
4Test‐OutCable:ConnectstoaDVRormonitor.
Note:Microphoneswithexternalpowersuppliesarerequired.

I/OTerminalBlock
TheI/Oterminalblock,locatedontherearpaneloftheBaseBoard,canbeusedtodevelopapplications
foralarminputandoutput,motiondetection,PTZcontroloravarietyofotherfunctions.
PinAssignment
No.FunctionsNo. Functions
1GND(Ground)7ALM_NC_A(AlarmOutputNormalCloseA)
2ALM_NO_B(AlarmOutputNormalOpenB)8GND(Ground)
3ALM_COM_B(AlarmOutputCommonB)9ALMIN1(AlarmInput1)
4ALM_NC_B(AlarmOutputNormalCloseB)10GND(Ground)
5ALM_NO_A(AlarmOutputNormalOpenA)11ALMIN2(AlarmInput2)
6ALM_COM_A(AlarmOutputCommonA)12GND(Ground)

 EPNSeries
3
4. OptionalAccessories
EPTZ‐PBOX(Externalpowerconnectionbox)

Cornermountadapter

Polemountadapter

Indoorceilingpendantmountbracket

Outdoorsunshield

Indoorrecessedmountbracket
Wallmountbracket

Indoorconcreteceilingmountadapter

EKB500(RS‐485keyboard)

EKB200(USBcontrollerkeyboard)


5. Installation
ThisinstallationguideprovidesthebasicinstructionsoninstallinganEPNseriesIPcamera.Fordetails,
refertotheEPNSeriesIPSpeedDomeUser’sManualinthesoftwareCD.

Note:Installationshouldbehandledbyaqualifiedserviceagentandcompliedwithalllocalregulations.

ReplacingtheDesiccantBags/InsertingaMicroSDCard
Beforeinstalling,insertamicroSDcardintothemainbodyandreplacethedesiccantbagsinsidethetop
housing.Itishighlyrecommendedtoreplacethedesiccantbagseverytimewhenyouopenthecamera.




 EPNSeries
4
Toreplacethedesiccantbags:
1. OntheTopHousing,slightlypresstheblackplasticsocketbackwardandliftupthebaseboard.

2. Removethedesiccantbagsfromthetophousing.
3. Stickthesupplied3newdesiccantbagsinsidethetophousing. Placebackthebaseboard.

Note:EnsureNottoplacethedesiccantbagsunderthepositionofthefan.



ToinsertamicroSDcard:
1. Unscrewthefourscrewsonthecameramainbodytoremovetheblackhousing.

2. InsertthemicroSDcardtothecardslot.Screwbacktheblackhousing.




 EPNSeries
5
InstallingOutdoorModels(EPN4122/4220)
Twomountingtypesareavailablefortheoutdoormodels:WallMountandCeilingMount.

WallMount
1. Drill4screw‐depthholesforthebracketbaseplateandthendrillathrough‐wallholeforthecamera
cables.Youcanoptionallydrillasecondthrough‐wallholetoseparatecablefeeding(seeStep4).
2. Attachthewaterproofsiliconpadtothebracketbaseplateforwaterproofing.
3. Feedthecamera’scablesthroughtheconduitinthewallmountbracket.

4. Connectthecamera’scablestotherelateddevices.Feedthecablesoftherelateddevices,suchasthe
speaker,throughthewallandthenthroughtheholesofthebracketbaseplate.

5. Screwthebracketbasetothewallusingthe4screws.
6. Screwthewallmountbrackettothebracketbaseusingthe4longscrews.
7. Putonthesuppliedgloves.Lineuptheredtriangles andthenpushthemainbodyupwardtothe
tophousing.Pushthemainbodyupwardintothetophousinguntiltheorangecatchesonbothsides
clickintoposition.
 
Note:Toreleasethemainbody,pressthetwoorangereleasebuttonsonbothsides.

8. Screwthehousingcovertothetophousingslowlybytwistingitclockwise.
Waterproof
siliconpad
Bracketbaseplate

 EPNSeries
6
CeilingMount
ItisrequiredtousetheoptionalIndoorRecessedMountBracketandSurfaceRingtoattachthecamerato
theceiling.
1. Cutaholeontheceilingusingthesuppliedtemplate.
2. Slightlyturnthesurfaceringandremoveitfromthebracket.

3. Placeandthenscrewthecamera’stophousingonthetopdiskofthebracketusingthe3shortscrews.

4. Useacableorothermechanismtohangthebracketontheceiling.Screwthe3rotationclipsofthe
bracketontheceilingusingascrewdriver.

5. Putonthesuppliedglovesandthenpushthemainbodyupwardtothetophousing.SeeStep7inWall
Mount.
6. Screwthehousingcovertothetophousingslowlybytwistingitclockwise.
7. Slidethesurfaceringtothefillisteronthebracket.
Note:Whenyouturnonthepower,thecamerawillenterself‐inspectionmodeandrunaself‐testing
program.Oncethisiscomplete,youwillbeabletooperateitviaanyIPnetwork.



 EPNSeries
7
6. NetworkConnections
Youcanuseoneofthemethodsbelowtoconnectthecameratothenetwork.

RouterorLANconnection
ThisisthemostcommonconnectioninwhichtheIPcameraisconnectedtoarouterandallowsmultiple
usersonandoffsitetoseetheIPcameraonaLAN/WAN(Internet).ThecameramustbeassignedanIP
addressthatiscompatiblewithitsLAN.Bysettingupportforwardingontherouter,youcanviewcameras
fromoutsideoftheLANviatheInternet.ToremotelyaccesstheWebinterfaceoftheIPcamera,please
referto7.3.2DDNSintheUser’sManual.Tosetupportforwarding,pleaseconsultthemanualofthe
router.





























Straight‐throughLANpatchcable
Right:Pinoutofastraight‐throughcable.

 EPNSeries
8
DirectHigh‐SpeedConnection
InaDirectHigh‐SpeedConnection,thecameraconnectsdirectlytoamodemwithouttheneedforarouter.
YouneedtosetthestaticordynamicWANIPaddressassignedbyyourISP(InternetServiceProvider)inthe
camera’sconfigurationwebpages.Toaccessthecamera,justtype“http://xxx”,wherexxxistheIPaddress
givenbyyourISP.IfyouhaveadynamicIPaddress,thisconnectionmayrequirethatyouuseDDNSfora
reliableconnection.Pleasereferto7.3.2DDNSintheUser’sManual.











One‐to‐oneConnection(DirectlyfromPCtoIPCamera)
Youcanconnectdirectlywithoutusingaswitch,routerormodem.However,onlythePCconnectedtothe
camerawillbeabletoviewtheIPcamera.YouwillalsohavetomanuallyassignacompatibleIPaddressto
boththecomputerandtheIPcamera.UnlessthePChasanothernetworkconnection,theIPcamerawill
betheonlynetworkdevicevisibletothePC.Seethediagrambelow:




Pinoutofstraightpatchcable      
4.AssignIPAddress




Right:Pinoutofacrossed‐overcable.

  EPNSeries
9
7. CheckingtheDynamicIPAddress
YoucanlookuptheIPaddressandaccesstheWebinterfaceofthecamerausingtheIPUtility(IPU)
software,whichisincludedinthesoftwareCD.
1. InstallandthenstarttheIPUprogram .Thefollowingdialogboxappears.

2. IPUwillautomaticallysearchthecamerasconnectedintheLAN.Thedefaultnetworkvaluesofthe
cameraswillbedisplayed.Bydefault,thenetworkprotocolofthecameraisDHCP.
3. Toconfigurethenetworksettings,selectacameraandthenclickLogin/MultiLogintologin.

4. TypetheuserIDandpassword.ClickOK.
Note:
1. ThedefaultuserIDisuser1andthedefaultpasswordis11111111.
2. IfyouselectmorethanonecamerathathasthesameuserID/password,youwillbeabletolog
inseveralcamerasatonce.




  EPNSeries
10
5. TochangetheIPsettings,double‐clickthevaluesinthecolumnandtypethenumbersorselectan
option.ClickSetIPAddresstosavethesettings.

Note:MostnetworkssupportDHCPprotocol,butifyouareunsureofyournetworkprotocol,please
consultyourIPadministratorfornetworkconfigurationdetails.
6. Toaccessthecamera,highlightthecameraandclickConnecttoSelectedIP.TheInternetExplorer
windowpopsup.
7. TypetheuserIDandpasswordtologin.TheLiveViewwindowofthecameraappears.

Note:
1. YoumightberequiredtodownloadActiveXforviewingthecamerafeed.Ifasked,clickYes.
2. ToenableRemoveLiveView,FirmwareUpgradeandActiveXPromptonInternetExplorer,some
settingshavetobecomplete.Pleasereferto4.2SettingsforMicrosoftInternetExplorerinthe
User’sManual.




  EPNSeries
11
8. UpgradingFirmware
Youcanupgradecamera’sfirmwareusingtheIPUtilitysoftware,whichisincludedinthesoftwareCD.

1. FollowStep1toStep4in7.CheckingtheDynamicIPAddresstologinthecamera.
2. ChecktheboxtoselectthecameraandthenclickUpgradeFirmware.Abrowsingwindowappears.

3. Selectthefirmwarefile(.evb)andthenclickOpen.TheIPUtilitywillautomaticallyupgradethe
firmware.


Thecamerawillrebootoncetheupdateiscomplete.ClickFindDevices,thenewfirmwareversionshould
bedisplayedinthelastpartoftheMachineName.






EverFocusElectronicsCorp.

EverFocusTaiwan:
12F,No.79,Sec.1,Shin‐TaiWuRoad,
Hsi‐Chih,Taipei,Taiwan
TEL:+886226982334
FAX:+886226982380
www.everfocus.com.tw
[email protected]
EverFocusEurope‐Germany:
Albert‐Einstein‐Strasse1,D‐46446
Emmerich,Germany
TEL:+49282293940
FAX:+492822939495
www.everfocus.de
[e-mail]
EverFocusChina‐Beijing:
Room609,TechnologyTradeBuilding,
ShangdiInformationIndustryBase,
HaidianDistrict,Beijing100085,China
TEL:+861062973336~39
FAX:+861062971423
www.everfocus.com.cn
[email protected]
EverFocusChina‐Shenzhen:
4F,No.2,D4Building,WanYelong
IndustrialPark,TangtouRoad,Shiyan,
Baoan,Shenzhen,Guangdong518101,China
TEL:+8675527651313
FAX:+8675527650337
www.everfocus.com.cn
[email protected]
EverFocusUSA‐California:
1801HighlandAvenue,UnitA,Duarte,CA91010,USA
TEL:+16268448888
FAX:+16268448838
www.everfocus.com
[email protected]
EverFocusUSA‐NewYork:
415OserAvenue,UnitS,Hauppauge,NY11788,USA
TEL:+16314365070
FAX:+16314365027
www.everfocus.com
[email protected]
EverFocusJapan:
5F,KinshichoCityBuilding,2‐13‐4Koto‐Bashi,Sumida‐Ku,
Tokyo,130‐0022,Japan
TEL:+81356258188
FAX:+81356258189
www.everfocus.co.jp
[e-mail]
EverFocusEurope‐UK:
Unit12,SpitfireBusinessPark,
HawkerRoad,CroydonSurrey,CR04WD,UK
TEL:+442086499757/+448454309999
FAX:+442086499907
www.everfocusuk.co.uk
[email protected]
EverFocusIndia:
Suite803,HousefinBhavan,C‐21,
BandraKurlaComplex,Bandra(East),
Mumbai400051,India
TEL:+912261288700
FAX:+912261288705
www.everfocus.in
[email protected]





Y
our EverFocus product is desi
g
ned
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605PP4122B010A‐Ver.E