EverFocus EZA1240 eZ.HD Series User manual

EZA1240 eZ.HD Series
1080p FHD IP66 IR Bullet Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: April, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1
1. Introduction
EverFocus eZ.HD series cameras – EZA1240 deliver 1080p full HD image quality.
The model provides 3.6mm fixed lens with ICR. Featured with Digital Wide
Dynamic Range (D-WDR), the camera can provide clear images even under
backlight circumstances where intensity of illumination can vary excessively.
The EZA1240 supports both NTSC and PAL scanning systems and is IP66
certified.
1.1 Packing List
Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 3
User Manual x 1
1.2 Features
Equipped with 1080p Full HD CMOS sensor to deliver stunning image
quality
3.6mm fixed lens with ICR to capture the desired field of view
Extended IR range of up to 25m / 82ft. with 20 LEDs (depends on scene
IR reflectivity)
D-WDR to improve the visibility under high contrast scene
The flexible angle viewing with its 3-Axis rotation design allows wall or
ceiling mounting
IP66-rated with metal housing
Supports UTC function: Control camera OSD settings directly from DVR
end

2
1.3 Dimensions
70mm / 2.76"
157mm / 6.18" 66mm / 2.6"
1.4 Optional Accessory
BA-E310
Color / Material: White / Metal
Size (Φx H): 101 x 52mm / 3.98”x 2”
Weight: 540g / 1.2lb
1.5 Cable Description
Power Cable
Video Output Cable
1
2
No. Name Descriptions
1 Power Cable Connects to a 12VDC power source.
2 Video Output 1080p output, using 75 Ohm BNC-type coaxial cable.
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 3 screw
positions. Drill 3 holes on the surface and insert the supplied 3 Screw
Anchors into the screw holes. If you want to run the cable through the
surface, drill a hole within the 3 screw area.

3
2. To mount the camera to the surface, screw the Camera Base to the surface
using the supplied 3 Screws.
Mounting
Surface
Screws Screw Anchors
Camera Base
3. Connect the Power Cable to a 12VDC power source. Connect the Video
Output Cable to a monitor or DVR.
4. You can use the Joystick on the cable to configure camera OSD settings or
switch to different video formats. Remove the Protection Cap from the
Joystick before using it.
UP
DN
Switching Video Format:
•Push the joystick up for 5 sec. to switch to
AHD.
•Push the joystick right for 5 sec. to switch
to TVI.
•Push the joystick down for 5 sec. to switch
to CVI.
•Push the joystick left for 5 sec. to switch to
CVBS.
Configuring OSD Settings:
•Push the Joystick up / down to select
among menu items.
•Push the Joystick left / right to adjust the
level of the selected item.
•Press the Joystick to enter the submenu or
exit the OSD Setup Menu.

4
5. You can optionally adjust camera angles. To do so, loosen the Rotate Screw
on the bracket using the supplied L-Type Wrench to adjust camera angles.
After adjusting camera angles, tightly screw back the Rotate screw.
Rotate Screw

5
3. Configuration in the OSD Menu
No
Main
Sub Menu
Sub Menu / Function
1 AE
Brightness
0-100
Exposure
Mode
Global
Center
FLC
BLC
0-7
Return
2 AWB Mode
ATW
Gray World
MWB
R Gain
0-63
B Gain
0-63
Return
3 Day/Night Mode
Auto
Gain Day/Night
Low/Middle/High
Gain Night/Day
Low/Middle/High
Color
B/W
Return
4 Image
Enhance
Contrast
Auto/Manual
0-20
Sharpness
Auto/Manual
0-20
Saturation
Auto/Manual
0-20
3DNR
Auto/Manual
0-20
2DNR
Auto/Manual
0-20
DWDR
Close/Open
Return
5 Video
Setting
AHD
1080P25/1080P30/720P25/720P30
TVI
1080P25/1080P30/720P25/720P30
CVI
1080P25/1080P30/720P25/720P30
CVBS
PAL/NTSC
Apply & Reboot
Return
6
Language
ENG/CHN/CHN(T)/RUS/SPA/FRA/POL/ITA/POR/JAP/KOR/GRE
7 Function
Privacy
Mode
On/Off
Area 0-3
Display
On/Off
X Position Start
0-100
Y Position Start
0-100
Width
0-100
Height
0-100
Return
Color
Red/Green/Blue
Transparency
On/Off
Return
Motion
Mode
On/Off
Area 0-3
Display
On/Off
X Position Start
0-100
Y Position Start
0-100
Width
0-100
Height
0-100
Return

6
Color
Red/Green/Blue
Transparency
On/Off
Return
Return
8
Version
9
Reset
10
Save & Exit
11
Exit