EverFocus eZ.HD Series User manual

EBA1280 eZ.HD Series
1080p FHD IP66 IR Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: May, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1
1. Introduction
EverFocus eZ.HD series cameras – EBA1280 deliver 1080p full HD image quality.
The model provides 2.8-12mm lens with ICR. Featured with Digital Wide
Dynamic Range (D-WDR), the camera can provide clear images even under
backlight circumstances where intensity of illumination can vary excessively.
The EBA1280 supports both NTSC and PAL scanning systems and is IP66
certified.
1.1 Packing List
Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 4
User Manual x 1
1.2 Features
Equipped with 1080p Full HD CMOS sensor to deliver stunning image
quality
Varifocal 2.8-12mm with ICR to capture the desired field of view
Extended IR range of up to 30m / 98ft. with 24 LEDs (depends on scene
IR reflectivity)
D-WDR to improve the visibility under high contrast scene
The flexible angle viewing with its 3-Axis rotation design allows wall or
ceiling mounting
IP66-rated with metal housing
Supports UTC function: Control camera OSD settings directly from DVR
end

2
1.3 Dimensions
98mm / 3.86"
120mm / 4.72"
60.2mm / 2.37"
1.4 Optional Accessory
BA-
E320
Color / Material: White / Metal
Size (Φx H): 138 x 54mm / 5.43”x2.13”
Weight: 700g / 1.5lb
BA-
EB45
Color / Material: White / Metal
Size (W x D x H): 245x160x163mm / 9.65”x6.3”x6.42”
Weight: 2.1kg / 4.63lb
1.5 Cable Description
Power Cable
Video Output Cable
1
2
No. Name Descriptions
1 Power Cable Connects to a 12VDC power source.
2 Video Output 1080p output, using 75 Ohm BNC-type coaxial cable.

3
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 4 screw
positions. Drill four holes on the surface and insert the supplied 4 Screw
Anchors into the screw holes. If you want to run the cable through the
surface, drill a hole within the 4 screw area.
2. Unscrew the Outer Housing by twisting it counterclockwise and then
remove it from the Camera Base.
Outer Housing
Camera Base
Camera Body
3. Screw the Camera Base to the surface with the supplied four Screws.
a. If you want to wire the cables from the Side Cut on the Camera Base:
Attach the Camera Body to the Camera Base and run the cables through
the Camera Base first, and then place the cable under the Side Cut.
Finally, screw the Camera Base to the surface with the supplied 4
Screws.
Side Cut
Wall
Camera Base
Camera Body

4
b. If you want to wire the cables through the surface:
Attach and screw the Camera Base to the surface with the supplied 4
Screws, and then attach the Camera Body to the Camera Base.
Wall
Camera Base
Camera Body
4. Screw back the Outer Housing and adjust the camera angle
simultaneously.
360°
180°
180°
5. Connect the Power Cable to a 12VDC power source. Connect the Video
Output Cable to a monitor or DVR.
6. For the first time installation, check whether the camera is properly
focused. If not, you can optionally adjust camera zoom and focus by
adjusting the Zoom Screw or Focus Screw using a slotted screwdriver.
Zoom
Focus

5
7. You can use the Joystick on the cable to configure camera OSD settings or
switch to different video formats. Remove the Protection Cap from the
Joystick before using it.
UP
DN
Switching Video Format:
•Push the joystick up for 5 sec. to switch to
AHD.
•Push the joystick right for 5 sec. to switch
to TVI.
•Push the joystick down for 5 sec. to switch
to CVI.
•Push the joystick left for 5 sec. to switch to
CVBS.
Configuring OSD Settings:
•Push the Joystick up / down to select
among menu items.
•Push the Joystick left / right to adjust the
level of the selected item.
•Press the Joystick to enter the submenu or
exit the OSD Setup Menu.

6
3. Configuration in the OSD Menu
No
Main
Sub Menu
Sub Menu / Function
1 AE
Brightness
0-100
Exposure
Mode
Global
Center
FLC
BLC
0-7
Return
2 AWB Mode
ATW
Gray World
MWB
R Gain
0-63
B Gain
0-63
Return
3 Day/Night Mode
Auto
Gain Day/Night
Low/Middle/High
Gain Night/Day
Low/Middle/High
Color
B/W
Return
4 Image
Enhance
Contrast
Auto/Manual
0-20
Sharpness
Auto/Manual
0-20
Saturation
Auto/Manual
0-20
3DNR
Auto/Manual
0-20
2DNR
Auto/Manual
0-20
DWDR
Close/Open
Return
5 Video
Setting
AHD
1080P25/1080P30/720P25/720P30
TVI
1080P25/1080P30/720P25/720P30
CVI
1080P25/1080P30/720P25/720P30
CVBS
PAL/NTSC
Apply & Reboot
Return
6
Language
ENG/CHN/CHN(T)/RUS/SPA/FRA/POL/ITA/POR/JAP/KOR/GRE
7 Function
Privacy
Mode
On/Off
Area 0-3
Display
On/Off
X Position Start
0-100
Y Position Start
0-100
Width
0-100
Height
0-100
Return
Color
Red/Green/Blue
Transparency
On/Off
Return
Motion
Mode
On/Off
Area 0-3
Display
On/Off
X Position Start
0-100
Y Position Start
0-100
Width
0-100
Height
0-100
Return

7
Color
Red/Green/Blue
Transparency
On/Off
Return
Return
8
Version
9
Reset
10
Save & Exit
11
Exit