evertz CP-2272E User manual

CP-2272E
Control Panel
User Guide
© Copyright 2012
EVERTZ MICROSYSTEMS LTD.
5288 John Lucas Drive,
Burlington, Ontario, Canada
L7L 5Z9
Phone: [phone]
Sales Fax: [phone]
Tech Support Phone: [phone]
Tech Support Fax: [phone]
Internet: Sales: [e-mail]
Tech Support: [email protected]
Web Page: http://www.evertz.com
Version 1.0, May 2012
The material contained in this manual consists of information that is the property of Evertz Microsystems and is
intended solely for the use of purchasers of the CP-2272E. Evertz Microsystems expressly prohibits the use of
this manual for any purpose other than the operation of the device.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz
Microsystems Ltd. Copies of this guide can be ordered from your Evertz products dealer or from Evertz
Microsystems.

This page left intentionally blank

IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “Dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (Servicing) instructions
in the literature accompanying the product.
•Read these instructions.
•Keep these instructions.
•Heed all warnings.
•Follow all instructions.
•Do not use this apparatus near water
•Clean only with dry cloth.
•Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
•Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
•Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
•Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
•Only use attachments/accessories specified by the manufacturer.
•Unplug this apparatus during lightning storms or when unused for long periods of time.
•Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC –
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
WARNING
DO NOT EXPOSE THIS EQUIPMENT TO
DRIPPING OR SPLASHING AND ENSURE THAT NO
OBJECTS FILLED WITH LIQUIDS ARE PLACED ON THE EQUIPMENT.
WARNING
TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE
POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE.
WARNING
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE.

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to the European Union EMC directive. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s
authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface
cables with the shield connected to the chassis ground of the device must be used.

CP-2272E
Revision 1.0 Page i
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 First Release May 2012
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof
nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning
performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The
only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order
confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no
warranty is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or
order confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If
you encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make
changes in equipment design or specifications.

CP-2272E
Page ii Revision 1.0
This page left intentionally blank

CP-2272E
Revision 1.0 Page iii
TABLE OF CONTENTS
1. OVERVIEW .......................................................................................................................1
2. INSTALLATION.................................................................................................................2
2.1. REAR PANEL..................................................................................................................2
2.1.1. Serial Connections .............................................................................................2
2.1.2. Joystick ..............................................................................................................2
2.1.3. QLINK 1 / 2 ........................................................................................................2
2.1.4. USB Control .......................................................................................................2
2.1.5. Ethernet Connection...........................................................................................3
2.1.6. Power Connections ............................................................................................4
2.2. MOUNTING......................................................................................................................4
3. TECHNICAL DESCRIPTION.............................................................................................5
3.1. SPECIFICATIONS ...........................................................................................................5
3.1.1. Control................................................................................................................5
3.1.2. Electrical.............................................................................................................5
3.1.3. Physical..............................................................................................................5
3.1.4. Compliance ........................................................................................................5
4. FRONT PANEL CONTROL...............................................................................................6
4.1. FRONT CONTROL PANEL .............................................................................................6
4.2. MAIN MENU.....................................................................................................................7
4.2.1. Setup..................................................................................................................7
4.2.1.1. Setting the IP Address of the Control Panel.......................................7
4.2.1.2. Setting the Netmask...........................................................................8
4.2.2. Setting the Broadcast Address...........................................................................8
4.2.3. Setting the Gateway...........................................................................................8
4.2.3.1. Saving Changes.................................................................................9
4.2.3.2. Undo Changes ...................................................................................9
4.2.3.3. Exit.....................................................................................................9
4.2.4. Performing a SHAFT Test..................................................................................9
4.2.5. Exit.....................................................................................................................9
4.2.6. Performing a KEY Test.....................................................................................10
4.2.7. Performing a GPI Test......................................................................................10
4.2.8. Performing a TFT Test.....................................................................................10
4.2.9. Controls............................................................................................................10
4.2.10. Exit Control.......................................................................................................11
4.2.11. Reboot Control .................................................................................................11
4.2.12. Shutdown Control.............................................................................................11

CP-2272E
Page iv Revision 1.0
5. SYSTEM CONFIGURATION .......................................................................................... 12
5.1. UPGRADING THE CP-2272E PANEL ...........................................................................12
5.1.1. System Requirements......................................................................................12
5.1.2. Identifying the IP Address.................................................................................12
5.1.3. Upgrading Firmware on the CP-2272E.............................................................12
5.1.4. Navigating to the Panel Configuration Page.....................................................15
Figures
Figure 1-1: CP-2272E Control Panel ................................................................................................................1
Figure 2-1: CP-2272E Rear Panel....................................................................................................................2
Figure 4-1: CP-2272E Front Control Panel.......................................................................................................6
Figure 5-1: CP2272e Main Screen .................................................................................................................12
Figure 5-2: Uploading Progress Window........................................................................................................13
Figure 5-3: Upgrade the CP2272e..................................................................................................................13
Figure 5-4: Upgrading Progress Window........................................................................................................14
Figure 5-5: Successful Firmware Upgrade .....................................................................................................14
Figure 5-6: CP-2272E Configuration Interface in EQX Server .......................................................................16
Figure 5-7: Type Drop Down Menu.................................................................................................................17
Figure 5-8: Populated Control Panel Interface................................................................................................18
Figure 5-9: Moving Buttons using Drag and Drop...........................................................................................19
Figure 5-10: Control Buttons...........................................................................................................................19
Tables
Table 2-1: Standard RJ-45 Wiring Colour Codes.............................................................................................3
Table 5-1: Type Drop Down Menu..................................................................................................................18

CP-2272E
Revision 1.0 Page 1
1. OVERVIEW
The CP-2272E remote control panel features two small high resolution color LCD displays alongside
an array of 72 full color dynamic LCD buttons, all of which are fully programmable. The two LCD
displays intelligently interact with the panel's buttons and rotary controls, updating automatically as
different operation facilities are selected.
Each of the 72 LCD buttons is capable of displaying a multiple character text string. They can also be
configured with a menu structure which allows quick navigation through the systems. When a menu
button is pressed some or all of the buttons change their function and legend. Their operation is then
defined by the configuration setup for this new menu. The selection of a new menu can also be
configured to change the graphical display of one or both the LCD screens.
The CP-2272E within the Evertz's MAGNUM control system, can interface with automated tielines and
pathfinding, and advanced breakaway routing while still supporting basic routing concepts like levels
and categories. The CP-2272E requires the EQX SERVER/MAGNUM Control System for router
control.
The CP-2272E is a very sophisticated advanced panel that allows you to create a very powerful and
very simple interface to your entire system. It is ideal for applications where a panel design with more
LCD buttons is critical based on number of sources, destinations, levels to control etc. is desired. This
makes it perfect in many different environments including Production areas, Technical Director areas,
"Tape" areas etc. Considering its small foot print the CP-2272E is perfect for use as an advanced
system control panel in truck and mobile applications.
Figure 1-1: CP-2272E Control Panel
Features:
•Flexible feature or menu driven configurations providing quick and simple access
•Two small high quality LCD displays which dynamically react with the panels buttons and rotary
controls
•Easily reconfigured for regularly changing environments
•Advanced control system interface
•Fully programmable buttons

CP-2272E
Page 2Revision 1.0
2. INSTALLATION
2.1. REAR PANEL
Figure 2-1 shows the rear view of the CP-2272E control panel. The CP-2272E is a 2RU panel with
various connection ports. Sections 2.1.1 to 2.1.5 describe the function of the connectors on the rear
panel.
Figure 2-1: CP-2272E Rear Panel
2.1.1. Serial Connections
SERIAL: Serial port 1, female 9 pin D connector that is used as the RS-232 console port.
2.1.2. Joystick
This male DB9 connector is used for connection to a camera control unit to allow the joystick push
buttons to override the router.
2.1.3. QLINK 1 / 2
These ports are not used at this time
2.1.4. USB Control
This USB 2.0 Port is used for USB-based firmware upgrades of the CP-2272E.

CP-2272E
Revision 1.0 Page 3
2.1.5. Ethernet Connection
The panel uses 10Base-T (10 Mbps), 100Base-TX (100 Mbps) twisted pair Ethernet cabling systems.
Ethernet Port A and Port B are not bonded redundant network connections. Only one Ethernet can be
connected at one time. When connecting for 10Base-T systems, category 3, 4, or 5 UTP cable as well
as EIA/TIA – 568 100ΩSTP cable may be used. When connecting for 100Base-TX systems, category
5 UTP cable is required. The cable must be “straight-through” with an RJ-45 connector at each end.
Establish the network connection by plugging one end of the cable into the RJ-45 receptacle of the
card and the other end into a port of the supporting hub.
The straight-through RJ-45 cable can be purchased or can be constructed using the pin-out
information in Table 2-1. A colour coded wiring table is provided in Table 2-1 for the current RJ-45
standards (AT&T 258A or EIA/TIA 258B colour coding shown). Also refer to the notes following the
table for additional wiring guide information.
Pin
1
Pin #
Signal
EIA/TIA 568A
AT&T 258A or
EIA/TIA 568B
10BaseT
or 100BaseT
1
Transmit +
White/Green
White/Orange
X
2
Transmit –
Green/White or White
Orange/White or Orange
X
3
Receive +
White/Orange
White/Green
X
4
N/A
Blue/White or Blue
Blue/White or Blue
Not used (required)
5
N/A
White/Blue
White/Blue
Not used (required)
6
Receive –
Orange/White or Orange
Green/White or Green
X
7
N/A
White/Brown
White/Brown
Not used (required)
8
N/A
Brown/White or Brown
Brown/White or Brown
Not used (required)
Table 2-1: Standard RJ-45 Wiring Colour Codes
Note the following cabling information for this wiring guide:
•Only two pairs of wires are used in the 8-pin RJ-45 connector to carry Ethernet signals.
•Even though pins 4, 5, 7 and 8 are not used, it is mandatory that they be present in the cable.
•10BaseT and 100BaseT use the same pins (a crossover cable made for one will also work with
the other).
•Pairs may be solid colours and not have a stripe.
•Category 5 cable must use Category 5 rated connectors.
The maximum cable run between the router and the supporting hub is 300 ft (90 m). The maximum
combined cable run between any two end points (i.e. router and PC/laptop via network hub) is 675 feet
(205 m).
Devices on the Ethernet network continually monitor the receive data path for activity as a means of
checking that the link is working correctly. When the network is idle, the devices also send a link test
signal to one another to verify link integrity. The rear panel is fitted with two LEDs to monitor the
Ethernet connection.
100:This Amber LED is ON when a 100Base-TX link is last detected. The LED is OFF when a
10Base-T link is last detected (the LINK LED is ON). Upon power-up the LED is OFF as
the last detected rate is not known and therefore defaults to the 10Base-T state until rate
detection is completed.

CP-2272E
Page 4Revision 1.0
LN/ACT: This dual purpose Green LED indicates that the card has established a valid linkage to its
hub, and it identifies whether the module is sending or receiving data. This LED will be
ON when the module has established a good link to its supporting hub. This gives you a
good indication that the segment is wired correctly. The LED will BLINK when the module
is sending or receiving data. The LED will be OFF if there is no valid connection.

The Ethernet ports on the CP2272E are not redundant. Only one port should be
wired and active
2.1.6. Power Connections
The CP-2272E power supply operates on a +12V and automatically senses the input voltage. Power
should be applied by connecting a 3-wire grounding type power supply cord to the power entry module
on the rear panel. The power cord should be minimum 18 AWG wire size; type SVT marked VW-1,
maximum 2.5 m in length.
The IEC 320 power entry module combines a standard power inlet connector, two 5 x 20 mm fuse
holders and an EMI line filter.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, GROUNDING OF THE
GROUND PIN OF THE MAINS PLUG MUST BE MAINTAINED
2.2. MOUNTING
The CP-2272E is equipped with rack mounting angles and fits into a 19.04 inch by 3.47 inch by 3.911
inch (483.62 mm x 88.14 mm x 3.911 mm) rack space.
Cooling is achieved by fan-assisted convection. Air is drawn into the right side of the chassis and
expelled as hot air from the left side of the chassis.

When installed in the equipment rack, ensure that the air flow from the right and left
side vents is not blocked or restricted.

CP-2272E
Revision 1.0 Page 5
3. TECHNICAL DESCRIPTION
3.1. SPECIFICATIONS
3.1.1. Control
•Joystick Parallel contact closure TTL levels, D9 male
•Ethernet 10/100 base T, RJ45 connector
3.1.2. Electrical
Voltage: +12V
Power: 24 Watts maximum
Fuse Rating: 2A
3.1.3. Physical
Height: 3.47” (88.14mm)
Width: 19.04” (483.62mm)
Depth: 3.911” (99.34mm)
Weight: 3lbs (1.36kg)
Operating Temp: 0-40°C
3.1.4. Compliance
Safety: ETL Listed, complies with EU safety directives
EMI/RFI: Complies with FCC Part 15 Class A regulations
Complies with EU EMC directive

CP-2272E
Page 6Revision 1.0
4. FRONT PANEL CONTROL
4.1. FRONT CONTROL PANEL
The CP-2272E has both rotary encoders and programmable LED buttons on its front panel. There are
4 rotary shaft encoders and a total of 72 programmable LED buttons. Rotary encoders are used to
access and adjust panel settings. There are two display windows which are used to display source,
destination and level information.
Figure 4-1: CP-2272E Front Control Panel
Please note that the blue labels in Figure 4-1 will NOT be displayed on the front panel of your CP-
2272E device. The labels listed above are for reference purposes only when describing the panel
controls in the following sections of the manual. The following chart describes the label and function of
the associated button.
Labels
Description
T1
Top Rotary encoder
M2
Middle 1 Rotary encoder
M3
Middle 2 Rotary encoder
B4
Bottom Rotary encoder
B1 to B72
1 to 72 programmable LED buttons
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
B63
B64
B65
B66
B67
B68
B69
B70
B71
B72
T1
M2
M3
B4

CP-2272E
Revision 1.0 Page 7
4.2. MAIN MENU
To enter the setup menu of the CP-2272E control panel press and hold the top (T1) and bottom (BM4)
rotary encoders on the far right side of the panel for approximately 6 seconds. The control panel
configuration options will appear on the button located on the right side of the panel. The user can
toggle through the menu options by pushing the button with the menu item name.
The menu items are outlined in the following table:
Menu Item
Menu Description
SETUP
Configuring the network setup
SHAFT Test
Tests the rotary encoders
CONTROLS
Intensity and font controls
KEY Test
Tests the LED buttons
GPIO Test
Tests the General Purpose Inputs
TFT Test
Tests that the TFTs are all functioning properly
EXIT
Exits the Configuration menu
REBOOT
Reboots the control panel
SHUTDOWN
Shuts down the control panel
4.2.1. Setup
The user can access the setup menu by pushing the Setup option by pushing the button called Setup.
The Setup menu will enable the user to set various network parameters. The changes to the settings
can be done with a single Save and Exit, user does not need to Save and Exit after each change.
The following parameters can be modified from this screen:
Menu Item
Menu Description
IP Addr
Enables the user to set and change the IP Address of the control panel
Netmask
Enables the user to set the Netmask Address of the control panel
Broadcast
Enables the user to set the Broadcast Address of the control panel
Gateway
Enables the user to set the Gateway Address of the control panel
Save and Exit
Pushing this option will save any changes made to the setup menu
Exit
Pushing this option will revert all changes and exit to the setup menu
Undo
Pushing this option will revert all changes
4.2.1.1. Setting the IP Address of the Control Panel
The IP Addr menu item is used to set the IP address of the CP-2272E control panel.
The IP address is displayed in the following format:
aaa.bbb.ccc.ddd
To change a value, push the button containing the value you want to change and use top level rotary
encoder to change the IP Address values. To change the value, rotate the encoder clockwise or
counter-clockwise. To move to the next three digits of the address, push the next button containing the
value you want to change.

CP-2272E
Page 8Revision 1.0
Once the IP address is set, use the Save and Exit button to save the changes and return to the top
level Setup menu.
4.2.1.2. Setting the Netmask
The Netmask menu item is used to set the netmask address of the CP-2272E control panel.
The netmask is displayed in the following format:
aaa.bbb.ccc.ddd
To change a value, psuh the button containing the value you want to change and use top level rotary
encoder to change the Netmask values. To change the value, rotate the encoder clockwise or counter-
clockwise. To move to the next three digits of the address, push the next button containing the value
you want to change.
Once the Netmask is set, use the Save and Exit button to save the changes and return to the top level
Setup menu
4.2.2. Setting the Broadcast Address
The Broadcast menu item is used to set the broadcast address for the CP-2272E control panel.
The broadcast address is displayed in the following format:
aaa.bbb.ccc.ddd
To change a value, push the button containing the value you want to change and use top level rotary
encoder to change the Broadcast Address values. To change the value, rotate the encoder clockwise
or counter-clockwise. To move to the next three digits of the address, push the next button containing
the value you want to change.
Once the Broadcast address is set, use the Save and Exit button to save the changes and return to
the top level Setup menu.
4.2.3. Setting the Gateway
The Gateway menu item is used to set the gateway address for the CP-2272E control panel.
The gateway address is displayed in the following format:
aaa.bbb.ccc.ddd
To change a value, push the button containing the value you want to change and use top level rotary
encoder to change the Gateway Address values. To change the value, rotate the encoder clockwise or
counter-clockwise. To move to the next three digits of the address, push the next button containing the
value you want to change.
Once the Gateway address is set, use the Save and Exit button to save the changes and return to the
top level Setup menu.

CP-2272E
Revision 1.0 Page 9
4.2.3.1. Saving Changes
Once all the appropriate changes have been made in the setup menu, push Save and Exit button to
save the changes.
4.2.3.2. Undo Changes
The Undo Changes option can be used when changes have been made in the setup menu but the
user no longer wants to apply these changes and wishes to revert to the original settings. As long as
the changes have not been saved, the user can revert back to the original settings by pushing the
Undo Changes button.
4.2.3.3. Exit
The Exit option can be used to exit the setup menu without saving or reverting changes
4.2.4. Performing a SHAFT Test
Entering the SHAFT Test mode enables the user to test the rotary encoders on the front of the CP-
2272E control panel. To enter Shaft Test mode, push the SHAFT Test button.
The two last button columns on the right side of the panel display 0s. The following is a list of the items
displayed on the second screen. Each row corresponds to a shaft encoder; the following table
identifies the corresponding row and shaft encoder:
Screen Display
Shaft Encoder
Shaft Test
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
Top Encoder (1)
Middle Encoder (2)
Middle Encoder (3)
Bottom Encoder (4)
The purpose of this test is to check the general functionality of each individual encoder. Watch the
display as you turn and push each encoder; the values on the screen should change for the
corresponding encoder. Rotating the encoder knob will increase (clockwise) and decrease (counter-
clockwise) numbers displayed in the column and row for the selected encoder. Pushing the encoder
knob in will increase the value of the first and second digits in increments of one.
4.2.5. Exit
Pushing any button on the CP2272E will exit the SHAFT Test menu.

CP-2272E
Page 10 Revision 1.0
4.2.6. Performing a KEY Test
Entering KEY Test mode enables the user to test that all 72 LCD buttons are functioning properly on
the front of the CP-2272E control panel. To enter Key Test mode, push the KEY Test button from the
main menu.
After pressing the KEY test button, all 72 LCD buttons should continuously flash and illuminate to
indicate that all buttons are functioning properly.
To test each individual button, push one of the buttons and the flashing test should stop. The user can
now test the functionality of each individual button. Pressing a button should illuminate it and key
information for that button will be shown in the second display screen.
For example,
Key Test
4 down 1 - indicates button ID #4 has been pushed down 1 time
4 up 1 - indicates button ID #4 has been depressed 1 time
To exit this test mode, push in the top right rotary encoder and you will return to the main engineering
menu.
4.2.7. Performing a GPI Test
Entering GPI Test mode enables the user to view and test the presence of the General Purpose
Inputs. To enter GPI Test mode, push the GPI Test button from the main
A list of GPIs will appear on buttons in the top, middle section of the panel. GPI button status colour will
change as each GPI is triggered from the joystick port.
To exit this test mode, press button Back button and you will return to the main menu.
4.2.8. Performing a TFT Test
To enter TFT Test mode, push the LED Test button from the main menu. TFT test mode enables the
user to check that the two TFTs are functioning properly. The user can toggle through different states
to ensure the TFTs will be illuminated properly during normal operation. Each TFT will have buttons
that trigger different tests for the TFT. Push a button with the test name you want to perform to trigger
the test.
To exit the TFT Test, push the Exit button.
4.2.9. Controls
To enter the Controls Mode, push the Controls button from the main menu. The Controls mode
enables the user to adjust LCD Intensity, TFT Intensity, Invert Text, Big Font, LCD Bold.
To change a value, push the button containing the value you want to change and use top level rotary
encoder to change the value.

CP-2272E
Revision 1.0 Page 11
Menu Item
Menu Description
LCD Intensity
Sets the intensity level for the LCD buttons
TFT Intensity
Sets the intensity level for the TFTs
Invert Text
Inverts the text on the LCD buttons
Big Font
Uses all 3 lines for mnemonics that do not exceed 5
characters
LCD Bold
Sets text to bold
4.2.10. Exit Control
Selecting the EXIT option from the main engineering menu will return the user to the regular operation
of the system.
4.2.11. Reboot Control
Selecting the REBOOT option from the main engineering menu will shut down and restart the panel.
4.2.12. Shutdown Control
Selecting the Shutdown option from the main engineering menu will completely shut down the panel

CP-2272E
Page 12 Revision 1.0
5. SYSTEM CONFIGURATION
5.1. UPGRADING THE CP-2272E PANEL
5.1.1. System Requirements
1. The user must have a laptop or PC connected to the same network as the CP-2272E.
2. In order to run the EQX / MAGNUM, you must have one of the following browsers installed on
your machine: Firefox, Chrome or Safari.
5.1.2. Identifying the IP Address
The IP Address can be identified using the procedure outlined below or by referring to section 4.2.1.1.
1. To identify the IP address, hold down the top and bottom rotary encoders (T1 and BM4) for
approximately 6 seconds.
2. When the main engineering menu appears, push to the SETUP menu button.
3. Next, select the IP Addr option and push in the Menu rotary encoder once again. Obtain the IP
address, which will appear on the third display screen.
4. At this time, ensure that one of the above mentioned browsers from section 5.1.1 is installed on
your machine.

Please note that the CP-2272E and the PC must be on the same network.
5.1.3. Upgrading Firmware on the CP-2272E
1. To upgrade firmware using the web interface, open a firefox web browser and enter the IP
address of the CP-2272E into the address field, and then press the <enter> key. The CP-2272E
Web Updater screen will appear, as shown in Figure 5-1.
Figure 5-1: CP2272e Main Screen